Date   

Re: First Satellite Contact

K6LCS <clintbrad4d@...>
 

OK. I did find a reference on a TX tone at ...

http://www.amsat.org/amsat-new/echo/index.php

BUT it also states - right above the frequencies -

"AO-51 Operational Frequencies- The following are the announced frequencies for AO-51. Please check the schedule before transmitting to AO-51 ... "

- and provided a link to the Control Team status page.

But I sure had to DIG to find that page!

If a visitor to amsat.org just looks on the left and chooses ...

Satellite Information
-status, frequencies
and satellite history

... they will be taken to the best-available info!

Clint


Re: First Satellite Contact

K6LCS <clintbrad4d@...>
 


Re: First Satellite Contact

ed palmer <flhtci97@...>
 

How about that?! I got that particular info from the Amsat website on the Echo project page.
 
Ed N0EHQ
 


--- On Mon, 11/30/09, K6LCS wrote:

From: K6LCS
Subject: [Work-Sat] Re: First Satellite Contact
To: Work-Sat@...
Date: Monday, November 30, 2009, 7:14 PM

 
>> ... made my first satellite contact ... AO-51 ... FT-817ND ... Arrow ...

Congratulations! Now on to SO-50 ... AO-27 ... (grin)

>> ... I did find out however it definitely works best if one has the PL tone set for the uplink.....DUH! !

NO - We are NOT using CTCSS on AO-51. Haven't for almost three years. And if you find a site with that mis-information, please write the owner top advise ... it means they haven't updated their info for three years!

Clint Bradford
AMSAT area coordinator



Re: First Satellite Contact

K6LCS <clintbrad4d@...>
 

... made my first satellite contact ... AO-51 ... FT-817ND ... Arrow ...
Congratulations! Now on to SO-50 ... AO-27 ... (grin)

... I did find out however it definitely works best if one has the PL tone set for the uplink.....DUH!!
NO - We are NOT using CTCSS on AO-51. Haven't for almost three years. And if you find a site with that mis-information, please write the owner top advise ... it means they haven't updated their info for three years!

Clint Bradford
AMSAT area coordinator


Re: First Satellite Contact

w6zkh@...
 

Now you'll get the FEVER, Ed !!  Welcome to Satellites....

John W6ZKH
DM06


----- Original Message -----
From: "flhtci97"
To: Work-Sat@...
Sent: Monday, November 30, 2009 4:01:55 PM GMT -08:00 US/Canada Pacific
Subject: [Work-Sat] First Satellite Contact

 

Hello Everyone,

Well I finally made my first satellite contact this evening on AO-51 using the FT-817ND and the Arrow II yagi.

I did find out however it definitely works best if one has the PL tone set for the uplink.....DUH!!

All I can say now is this satellite stuff is pretty doggone cool.

73 Ed N0EHQ


First Satellite Contact

flhtci97 <flhtci97@...>
 

Hello Everyone,

Well I finally made my first satellite contact this evening on AO-51 using the FT-817ND and the Arrow II yagi.

I did find out however it definitely works best if one has the PL tone set for the uplink.....DUH!!

All I can say now is this satellite stuff is pretty doggone cool.

73 Ed N0EHQ


Re: Which BNC-to-SMA Adapter?

K6LCS <clintbrad4d@...>
 

As long as the adapter "mates" well with the radio's case, it will provide some protection.

I like the design and finish of the Diamond you cited - here's a photo ...

http://rfparts.com/diamond/bncj-smap.html

I'll keep on using Stephen's adapters, 'cause I like the guy (grin). AND because he has done his research and has different adapters for different radios for us.

THANKS for the tip, Ed!

Clint


Re: Which BNC-to-SMA Adapter?

ed palmer <flhtci97@...>
 

I have found another SMA to BNC adapter that works well with the VX-8R. It is the BNCJ-SMAP adapter from Diamond Antenna. I don't know how it would work for other handhelds so your mileage may vary.
 
The adapter is wide at the base and mates up well with the rubber gasket around the SMA jack on the VX-8R. The last half turn will require one to hold on to the rubber gasket around the SMA when tightening down the adapter to keep the gasket from spinning. 
 
73 Ed N0EHQ

 
 

--- On Sun, 11/22/09, K6LCS wrote:

From: K6LCS
Subject: [Work-Sat] Which BNC-to-SMA Adapter?
To: Work-Sat@...
Date: Sunday, November 22, 2009, 11:32 AM

 
From my In Box ...

>> ... I have a large antenna with BNC male connector that I did not use because I need to get a adapter for the bnc so it can fit on my SMA radio ...

Please consider either a NCG/Comet HB-05 BNC female to SMA male 18-inch jumper, or the Stephen Gulyas adapter. Either will protect your radio's SMA jack and center pin from stress.

The HB-05 is available from fine ham radio stores nation-wide. Info on the Gulyas adapters available at ...

http://www.work- sat.com

Clint



Re: Which BNC-to-SMA Adapter?

K6LCS <clintbrad4d@...>
 

Great points - thanks!

Clint


Re: Which BNC-to-SMA Adapter?

Andy
 

I have Stephen Gulyas's adapter, and think it's pretty good for
mounting a BNC whip on the radio. I much prefer it to the straight
metal-only adapters. Highly recommended.

On the other hand, I think it is slightly inconvenient for adapting a
stiff or fat cable to the radio that has a BNC on its end (or perhaps
a UHF plug on which you've attached a UHF-BNC adapter). For that
situation, I'd probably recommend one of the short pigtail atapter
cables. The short length helps isolate the fatter cable's stiffness
from the little SMA jack, and is easier to attach and remove.

Andy


QSL Cards

K6LCS <clintbrad4d@...>
 

A couple folks have asked me where I had my QSL cards made.

I used Carl at ...

http://www.iqslusa.com/

Wasn't the "cheapest" source, but the quality and service was excellent.

Clint
909-241-7666


Re: Work SO-67!

K6LCS <clintbrad4d@...>
 

... How do I set my FT-60R up for SO-67?? Its only one freq isn't it?
Watch the sat's operating schedule for updates ...

http://www.amsatsa.org.za/

Last week, they had a cross-band repeater set up for many.

Uplink: 145.875MHz
Downlink: 435.345MHz
CTCSS 233.6

As with other FM sats, please program to compensate for the Doppler effect on the receive side.

Clint Bradford, K6LCS


Re: More Mods to Arrow Satellite Antenna

K6LCS <clintbrad4d@...>
 

... I have been using the Arrow and have been pondering such an addition, but I didn't have any design in mind. Now I do. I see you drilled a hole just behind the first element to put in a screw and wingnut. How far does the duplexer extend IN the handle?
You can actually slip the duplexer out and see ... There's about an inch if clearance 'tween my wing nut and the end of the duplexer.

Clint


AO-51 Performance 11/20/09 00:42 GMT

K6LCS <clintbrad4d@...>
 

I wrote last week ...

"Don't know exactly how to explain it, but the pass today at 4:42PM Pacific Standard Time didn't exhibit the "normal" silencing, then faint voices, then stronger voices. It plainly BLASTED into discernible conversations, and we we were able to work it much sooner than "normal." We were not hidden behind foothills. It was a pretty clear shot South to AOS. It really floored me - in a most positive way. It was dramatic."

And AMSAT's VP of Operations replied ...

"The power on the repeater downlink is a bit higher than normal at 760
mw. It shouldn't be a dramatic difference from our recent 500-600mw, but
noticeable to a observant operator ... - 73, Drew KO4MA

Well, my aging ears cannot take the credit ... I was using my standard setup - Arrow Sat Antenna and FT-60R.

Clint


Better Whip - or ELK / Arrow Antenna?

K6LCS <clintbrad4d@...>
 

... I am considering either the Elk or Arrow sat antennas. Are they going to be that much better than the Smiley 270A?
It's a tremendous difference! You can experience the gain improvement by making a simple Yagi yourself. There are a few articles here ...

http://www.work-sat.com

... including making a Yagi out of a steel tape measure ... or an old umbrella!

A friend in Texas has over 9,000 contacts with his Icom IC-W32a HT and the Anli/Pryme AL-800 antenna ... So you can certainly stick with your current setup!

This reminds me of when I purchased my little FT-817 - INSTEAD of, say, the FT-857. I mean, ANYONE can make long-distance contacts with 100W TX power. But something about only having 5W appealed to me ... a little more patience and finesse is involved ... (grin). Same with these FM satellites: Definitely workable with an HT and Smiley antenna ... but more easily worked with the gain priovided by an efficient Yagi or log-periodic antenna.

Clint


USB Hub Suggestions

K6LCS <clintbrad4d@...>
 

... I have been running a FT-817 and SatPC32 and sometimes HRD. I now want to add my FT-857 and run dual radio mode. I am using a Vista laptop. with a USB cable from two radios and one from a rotor control. It is a nightmare every time I unhook the laptop. Can you recommend a USB hub to connect all of this stuff to or a proper method. I am no computer whiz!

I'd stick with a name-brand for reliability ... and one that has an AC wall wart, so your USB lines get all the energy they expect.

I use a Kensington K331118A ...

http://us.kensington.com/html/6495.html

Belkin also makes quality powered USB hubs.

Macally makes a couple models of external hard drive enclosures which I have found to be great - but I am not sure if they currently offer powered USB hubs.

Clint


New Ham Antenna on ISS

K6LCS <clintbrad4d@...>
 

ARISS US Hardware Manager Lou McFadin, W5DID says that all the
teamwork and effort to expand the ARISS amateur radio station
aboard the ISS were successful this weekend when the new dual
band 2m/70CM antenna was installed on the outside of ESA's
Columbus module.

Lou congratulated the team, "This is an example of what can be
achieved by volunteer hams working closely with a space agency.
This antenna project was funded entirely by AMSAT-NA and volun-
teers who built the antennas for both an ESA experiment and for
ARISS. I am very proud of all the teamwork and effort that has
gone into this project."

The new ARISS antenna is very similar to the antennas already on
the Russian service module. Once the antennas are in place the
ARISS team will be working to bring amateur radio to the Columbus
module.

In conclusion Lou noted the tremendous contribution from ESA for
the experiment, the launch and the EVA making this expansion of
amateur radio aboard the ISS possible.

[ANS thanks Lou McFadin, W5DID for the above the information]


Which BNC-to-SMA Adapter?

K6LCS <clintbrad4d@...>
 

From my In Box ...

... I have a large antenna with BNC male connector that I did not use because I need to get a adapter for the bnc so it can fit on my SMA radio ...
Please consider either a NCG/Comet HB-05 BNC female to SMA male 18-inch jumper, or the Stephen Gulyas adapter. Either will protect your radio's SMA jack and center pin from stress.

The HB-05 is available from fine ham radio stores nation-wide. Info on the Gulyas adapters available at ...

http://www.work-sat.com

Clint


SO-67 Ops Notes from K8YSE

K6LCS <clintbrad4d@...>
 

From the FM-SATs group ...

Audio for the SO-67 eastern USA pass on 21Nov09
is on my webserver:

http://www.papays.com/SO-67_21Nov2009_143116z.mp3

Now that it is understood that there is a 3 second
tail after each transmission and audio will cut off
after that time has expired, ways to get around the
problem can be devised.

I found that when called by another station, if you start
transmitting before that station releases their transmitter,
you will be able to answer and not be cut off after 3 seconds.
This is because the "tail" never started. However, if this
continuous transmission goes on for 30(?) seconds, the next
timer will shut down the transmitter. Waiting for the tail
to expire, when the bird is over the USA with many stations
trying to get in, will not work. There will always be someone
who keys up during the 3 second tail.

Signals were loud as usual right down to the horizon. The extra
transmitter power will enable many new users to get on this bird.
Thanks to all of those who had a part in launching this satellite!

73,
John K8YSE


Re: How to program the FT-51R

K6LCS <clintbrad4d@...>
 

Well, Yahoo won't let me upload a file larget than 5MB - So tell me which email address to send this .pdf to - and I'll get it to you!

Clint

6461 - 6480 of 6575