Hi all, to complete a Vectra PC I am looking for the proper HP-HIL keyboard 46030 - with 2 groups of 4 function keys above and a group of function keys at the left..With US-ASCII or German layout. Thi

All this talk about disk formats and disk images etc. and trying to bring disk units up has brought back memories and gotten my attention as I go deeper into my gear. I recall proprietary disk format

The following files have been uploaded to the Files area of the VintHPcom@groups.io group. /HP9000 Series 200 300/Software/uEMACS.zip By: Anders Description: MicroEMACS work disk. A HP9134A image. Boo

There does not seem to exist a decent editor on CP/M 68K, but I found a copy of uEMACS that someone ported to CP/M68 and it runs on the 9816 after some tweaking. Not entirely sure if I should just kee

I tried out CP/M 68K on a 9920 and found that it will not boot with the MMU CPU however it does work with the original 68000 CPU cvard with memory. These same CPU cards are used in 9826 and 9836. I al

Hi all, I made a performance comparison with my 1000E (2113B) and 1000F (2117B) machines, using the simple assembler program of Mike Loewen, keyed in on the front panel and without any OS loaded. 100

The following files have been uploaded to the Files area of the VintHPcom@groups.io group. /HP9000 Series 200 300/Software/CPM68K_1_2.zip By: Anders Description: CP/M 68K v 1.2 for the HP98x6. HP9134A

Hello group members, my 7978B 1/2" Tape Drive drive is throwing a 5354 error during startup, which corresponds to 'Failure while forcing one track in error' (whatever this exactly means ;-) ). The las

hi, I had not seen these 2 'different' HP 9100 schematics before: http://www.bitsavers.org/pdf/hp/9100/ perhaps of use to 9100 fans ? wish there were more. Rik

Ie: http://bitsavers.org/bits/HP/HP_9000/cpm-68k/ There are TD0 files and IMG files that I assume are conversions thereof, but they all start booting on my 9816, then error out with "Unexpected use of

I have a 9836A but no monitor for it, and have been hoping to get video out to an LCD. I’ve looked at Tony Duell’s schematic which says on page 7 that in addition to video out and ground, it has “Int”

The following files have been uploaded to the Files area of the VintHPcom@groups.io group. /HP9000 Series 200 300/Software/CPM68K_Images.zip By: Anders Description: CP/M 68K for the series 200. Flat i

The following files have been uploaded to the Files area of the VintHPcom@groups.io group. /HP9000 Series 200 300/Software/CPM-68K For Hewlett-Packard Series 200 Computers/00_CPM-68K_HP_BoxedSet_READM

rmb_guru added folder /HP9000 Series 200 300/Software/CPM-68K For Hewlett-Packard Series 200 Computers

Hi all, in one of my 21MX power supplies the power transistor Q1 on the PSU mainboard has failed. HP part number is 1854-0869. According to HP Bench Briefs this is a GX55220A of General Semiconductor

The FORMAT command is very laconic. Usage: format disk [interleave] But FORMAT B: 9122 does not seem to work. What should I specify for disk type?

Hello Friends After some time collecting and fixing series 300 computers, I have decided to make a website on that series. Please take a look here: https://www.hp-series300.net. Feedback is most welco

Has anyone, Ansgar perhaps seen this puppy? For some reason has my HP1632D, started issuing those: [5F 1][3F 1][54 1][20 1][MLA][68 1][16 0][ 0 0] AM:Wakeup[3F 1][3F 1][54 1][20 1][MLA][68 1][ 3 0][ 0

I was working on my HP Integral and noticed that some programs were not executing today that used to run just fine a few months back. When I start some programs a window will begin to launch with the

Correction to subject - I have the small (but heavy) HP 9826 which is a 9000 226 (not 236). The service manual gives the row/column for each key, all my dead ones are either row 3, row 5 or column 12