1. UKMicrowaves@groups.io
Topics

Pin layout on Jupiter GPS modules

Denis Stanton G0OLX
 

Can some one please confirm how the pins are on a Jupiter TU35-410-041 Is it pin 2 is oposite 1, pin 4 oposite pin 3 ETC. or do they run like an IC 1 to 10 then back up the other way
11 to 20 many thanks
Denis G0OLX
Mark GM4ISM
 

see below  Full manual available  1.4Mb so i wont attach it here

On 05/02/2021 15:59, Denis Stanton G0OLX wrote:
Can some one please confirm how the pins are on a Jupiter TU35-410-041 Is it pin 2 is oposite 1, pin 4 oposite pin 3 ETC. or do they run like an IC 1 to 10 then back up the other way
11 to 20 many thanks
Denis G0OLX

Virus-free. www.avg.com

Mark GM4ISM
 

Sorry I forgot to say the manual is for the T30 flavour, but most info including pinout should be the same

On 05/02/2021 15:59, Denis Stanton G0OLX wrote:
Can some one please confirm how the pins are on a Jupiter TU35-410-041 Is it pin 2 is oposite 1, pin 4 oposite pin 3 ETC. or do they run like an IC 1 to 10 then back up the other way
11 to 20 many thanks
Denis G0OLX

Virus-free. www.avg.com

Denis Stanton G0OLX
 

Mark
Thank you very much 
None of the info downloaded off the web identified the other pins
Best 73’s
Denis



On 5 Feb 2021, at 16:08, Mark GM4ISM via groups.io <gm4ism@...> wrote:



Sorry I forgot to say the manual is for the T30 flavour, but most info including pinout should be the same

On 05/02/2021 15:59, Denis Stanton G0OLX wrote:
Can some one please confirm how the pins are on a Jupiter TU35-410-041 Is it pin 2 is oposite 1, pin 4 oposite pin 3 ETC. or do they run like an IC 1 to 10 then back up the other way
11 to 20 many thanks
Denis G0OLX

Virus-free. www.avg.com

Dave G8KHU
 

The TU35 datasheet just shows pin 1 and offer no clues but I've just buzzed out the ground connections( - pins 10 and 13 -) on a TU35-D410-041 (note te extra D if thats of any significance) and the orientation is as shown in Mark's TU30 document.

73 Dave
Dave G8KHU
 

The data-sheet I have is LA010065A dated August 4, 2003. I can forward off group if you'd like it.
FYI the mating connection is a Samtec SQW-110-01-L-D  - Farnell 1668192

73 Dave
DF6NA Rainer
 

Hi,

don't know if that helps:
Jupiter 12 Pinout
Pin     Name     Description
1     PREAMP     Antenna Preamp voltage input.
2     PWRIN     Primary +3.3/5 VDC power input.
3     VBATT     Battery backup voltage input.
4     PRWIN     Primary +3.3/5 VDC power input.
5     M_RESET     Master reset (active low).
6     GPIO     General Purpose I/O or Gyro input for DR
7     GPIO     General Purpose I/O or NMEA protocol Select/Reverse gear sensor for DR
8     GPIO     General Purpose I/O or EEPROM default select
9     GPIO     General Purpose I/O or Speed indication (wheel tick input) for DR.
10     GND     Ground.
11     SDO1     Serial data output port 1.
12     SDI1     Serial data input port 1.
13     GND     Ground.
14     SDO2     Serial data output port 2.
15     SDI2     Serial data input port 2.
16     GN     Ground.
17     GND     Ground.
18     GND     Ground.
19     TMARK     1 PPS time mark output
20     10KHz     10 KHz clock output.

73, Rainer


Am 05.02.2021 um 17:20 schrieb Denis Stanton G0OLX:

Mark
Thank you very much 
None of the info downloaded off the web identified the other pins
Best 73’s
Denis



On 5 Feb 2021, at 16:08, Mark GM4ISM via groups.io <gm4ism@...> wrote:



Sorry I forgot to say the manual is for the T30 flavour, but most info including pinout should be the same

On 05/02/2021 15:59, Denis Stanton G0OLX wrote:
Can some one please confirm how the pins are on a Jupiter TU35-410-041 Is it pin 2 is oposite 1, pin 4 oposite pin 3 ETC. or do they run like an IC 1 to 10 then back up the other way
11 to 20 many thanks
Denis G0OLX

Virus-free. www.avg.com

Denis Stanton G0OLX
 

Thanks for all the replies
Pin one is shown marked pin two is opposite pin 3 is next then pin 4 opposite pin 3 not like an Ic layout
Best 73’s


On 5 Feb 2021, at 16:42, DF6NA Rainer <df6na@...> wrote:


Hi,

don't know if that helps:
Jupiter 12 Pinout
Pin     Name     Description
1     PREAMP     Antenna Preamp voltage input.
2     PWRIN     Primary +3.3/5 VDC power input.
3     VBATT     Battery backup voltage input.
4     PRWIN     Primary +3.3/5 VDC power input.
5     M_RESET     Master reset (active low).
6     GPIO     General Purpose I/O or Gyro input for DR
7     GPIO     General Purpose I/O or NMEA protocol Select/Reverse gear sensor for DR
8     GPIO     General Purpose I/O or EEPROM default select
9     GPIO     General Purpose I/O or Speed indication (wheel tick input) for DR.
10     GND     Ground.
11     SDO1     Serial data output port 1.
12     SDI1     Serial data input port 1.
13     GND     Ground.
14     SDO2     Serial data output port 2.
15     SDI2     Serial data input port 2.
16     GN     Ground.
17     GND     Ground.
18     GND     Ground.
19     TMARK     1 PPS time mark output
20     10KHz     10 KHz clock output.

73, Rainer


Am 05.02.2021 um 17:20 schrieb Denis Stanton G0OLX:
Mark
Thank you very much 
None of the info downloaded off the web identified the other pins
Best 73’s
Denis



On 5 Feb 2021, at 16:08, Mark GM4ISM via groups.io <gm4ism@...> wrote:



Sorry I forgot to say the manual is for the T30 flavour, but most info including pinout should be the same

On 05/02/2021 15:59, Denis Stanton G0OLX wrote:
Can some one please confirm how the pins are on a Jupiter TU35-410-041 Is it pin 2 is oposite 1, pin 4 oposite pin 3 ETC. or do they run like an IC 1 to 10 then back up the other way
11 to 20 many thanks
Denis G0OLX

Virus-free. www.avg.com

1 - 8 of 8