Date   

Re: I'm hoping to be out portable on 23cms Tomorrow

Bob_G1ZJP
 

Phil, Paul

I'll be QRV from home tonight and looking for you both.

73
Bob, G1ZJP / M1MHZ


Re: 13cm beacons

Martyn G3UKV
 

Excellent news for 13cm.
3cm is the Cinderella now . . . . .
73 Martyn G3UKV

On 16/09/2019 19:02, John Worsnop wrote:
And GB3BSS will be on its way back to the beacon keeper tomorrow with shiny new GPS locking and JT4G sequence!
Your UkuG subs being put to good use again. 

73 John

On Mon, 16 Sep 2019, 17:40 Barry Lewis via Groups.Io, <barryplewis=btinternet.com@groups.io> wrote:
Folks,
GB3FNM back up and running on 2320.920 MHz from 15:20 today.
73
Barry G4SJH


Re: 13cm beacons

Ralph
 

Receiving it here at about 31-419 through fine misty rain

 

Thanks and 73

 

Ralph G4ALY

 

Sent from Mail for Windows 10

 

From: Barry Lewis via Groups.Io
Sent: 16 September 2019 17:40
To: UKMicrowaves@groups.io
Subject: Re: [UKMicrowaves] 13cm beacons

 

Folks,
GB3FNM back up and running on 2320.920 MHz from 15:20 today.
73
Barry G4SJH

 


Virus-free. www.avg.com


Re: 13cm beacons

John Worsnop
 

And GB3BSS will be on its way back to the beacon keeper tomorrow with shiny new GPS locking and JT4G sequence!
Your UkuG subs being put to good use again. 

73 John

On Mon, 16 Sep 2019, 17:40 Barry Lewis via Groups.Io, <barryplewis=btinternet.com@groups.io> wrote:
Folks,
GB3FNM back up and running on 2320.920 MHz from 15:20 today.
73
Barry G4SJH


Re: 13cm beacons

John Lemay
 

Many thanks Barry – another shilling in the meter was needed ?

 

I’ve just added a Cluster spot.

 

John G4ZTR

 

 

From: UKMicrowaves@groups.io [mailto:UKMicrowaves@groups.io] On Behalf Of Barry Lewis via Groups.Io
Sent: 16 September 2019 17:41
To: UKMicrowaves@groups.io
Subject: Re: [UKMicrowaves] 13cm beacons

 

Folks,
GB3FNM back up and running on 2320.920 MHz from 15:20 today.
73
Barry G4SJH


Re: I'm hoping to be out portable on 23cms Tomorrow

Phil Guttridge G3TCU
 

I'll also be out portable on 23cm tomorrow evening so I'll look for you
Paul (from IO91 near Guildford)

I'll be on 'KST

Strangely, I didn't receive Nick's original message that you replied to?

73, Phil G3TCU

On 16/09/2019 06:03, PAUL NICKALLS via Groups.Io wrote:
Correction - Tuesday evening for the UKAC.

G8AQA

On 15/09/2019 21:53, PAUL NICKALLS via Groups.Io wrote:
Hoping to be out on 23cms from IO82 Long Mynd tomorrow.
07967 272 185
KST
Zello


On 15/09/2019 16:07, Nick Gregory G0HIK via Groups.Io wrote:
As per the header.

I'll be out with 23cms and 2mtrs tomorrow from one of the Lake
district fells. Mainly to work Andrew G4VFL/P, but happy to work anyone.

I'll have Zello, but internet is flakey on Kirkby Moor, so a Text
may be better 07955635646.

Nick G0HIK

<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
Virus-free. www.avg.com
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>


<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>


Re: 13cm beacons

Barry Lewis
 

Folks,
GB3FNM back up and running on 2320.920 MHz from 15:20 today.
73
Barry G4SJH


Re: I'm hoping to be out portable on 23cms Tomorrow

Paul G8AQA
 

Correction - Tuesday evening for the UKAC.

G8AQA

On 15/09/2019 21:53, PAUL NICKALLS via Groups.Io wrote:
Hoping to be out on 23cms from IO82 Long Mynd tomorrow.
07967 272 185
KST
Zello


On 15/09/2019 16:07, Nick Gregory G0HIK via Groups.Io wrote:
As per the header.

I'll be out with 23cms and 2mtrs tomorrow from one of the Lake district fells. Mainly to work Andrew G4VFL/P, but happy to work anyone.

I'll have Zello, but internet is flakey on Kirkby Moor, so a Text may be better 07955635646.

Nick G0HIK


Virus-free. www.avg.com


Re: I'm hoping to be out portable on 23cms Tomorrow

Paul G8AQA
 

Hoping to be out on 23cms from IO82 Long Mynd tomorrow.
07967 272 185
KST
Zello


On 15/09/2019 16:07, Nick Gregory G0HIK via Groups.Io wrote:
As per the header.

I'll be out with 23cms and 2mtrs tomorrow from one of the Lake district fells. Mainly to work Andrew G4VFL/P, but happy to work anyone.

I'll have Zello, but internet is flakey on Kirkby Moor, so a Text may be better 07955635646.

Nick G0HIK


Virus-free. www.avg.com


Re: milling copper

Neil Smith G4DBN
 

For really nasty copper, I have used a heavy spring to pre-load the table against the leadscrew and bolted huge lumps of lead to the table, and even in one case, made a 3kg collar for the collet holder to give lots more rotational inertia. That was trying to fly-cut at 3 inch radius though.  I gave up and used two passes with an 80mm shell mill with just two polished carbide neutral inserts with a chip-breaker and used paraffin spray mist coolant in a Noga-Cool Mini.  Then I ditched C101 and moved to C111 and use normal tools and speeds/feeds without problems.  Janky material makes for janky finishes. Using neutral or negative rake and lots of tool pressure is supposed to help, and in fact with drilling, it does.  I use spiral-point taps on through-holes bigger than M4, and thread-rolling taps with some brown waxy cutting compound for M4/3/2.5

In other news, I have two 6 x 7 inch slabs of 3/8th inch mill-finish C101 which I'm trying to face flat and parallel for some French half-kW SSPAs on 23cm. Totally horrible. Harmonics and wavy chatter are making this job very ugly.  I should have superglued it to an inch-thick ally slab right from the start. I am an idiot.

Neil G4DBN

On 15/09/2019 18:20, geoffrey pike via Groups.Io wrote:
Thanks all, i will give a 2 flute mill a try, this 4 flute is digging in, oh and more rpm
cheers
Geoff
GI0GDP

On Sunday, 15 September 2019, 07:47:07 BST, DougF <uwaves@...> wrote:


Greetings to all.

My experience is that I have met my copper drilling/tapping/milling
needs by way of purchase of drill bits, taps and milling cutters which
are intended for use in cutting copper.  They do exist!  They also are
great when trying to work with brass, some alloys of which are tough and
likely to break whichever tool is in use.

FWIW.....

--Doug Friend, VK4OE.

On 15/09/2019 3:51 pm, Mike Willis wrote:
> Best solution, find someone else to do it who can do it properly.
> Otherwise you get a poor finish, or a tap breaking and getting stuck
> just as you tap the last of 20 holes.
> Mike G0MJW



Re: I'm hoping to be out portable on 23cms Tomorrow

Dave - G4RQI
 

Hello Nick

 

I currently have 23cm up but I am only QRV after 5:30pm so what time are you going to be out and what is your locator going to be?

 

73 David – G4RQI

Sent from Mail for Windows 10

 


From: UKMicrowaves@groups.io <UKMicrowaves@groups.io> on behalf of Nick Gregory G0HIK via Groups.Io <nickg0hik@...>
Sent: Sunday, September 15, 2019 4:07:25 PM
To: UKMicrowaves@groups.io <UKMicrowaves@groups.io>
Subject: [UKMicrowaves] I'm hoping to be out portable on 23cms Tomorrow
 
As per the header.

I'll be out with 23cms and 2mtrs tomorrow from one of the Lake district fells. Mainly to work Andrew G4VFL/P, but happy to work anyone.

I'll have Zello, but internet is flakey on Kirkby Moor, so a Text may be better 07955635646.

Nick G0HIK


Re: milling copper

geoffrey pike
 

Thanks all, i will give a 2 flute mill a try, this 4 flute is digging in, oh and more rpm
cheers
Geoff
GI0GDP

On Sunday, 15 September 2019, 07:47:07 BST, DougF <uwaves@...> wrote:


Greetings to all.

My experience is that I have met my copper drilling/tapping/milling
needs by way of purchase of drill bits, taps and milling cutters which
are intended for use in cutting copper.  They do exist!  They also are
great when trying to work with brass, some alloys of which are tough and
likely to break whichever tool is in use.

FWIW.....

--Doug Friend, VK4OE.

On 15/09/2019 3:51 pm, Mike Willis wrote:
> Best solution, find someone else to do it who can do it properly.
> Otherwise you get a poor finish, or a tap breaking and getting stuck
> just as you tap the last of 20 holes.
> Mike G0MJW



I'm hoping to be out portable on 23cms Tomorrow

Nick Gregory G0HIK
 

As per the header.

I'll be out with 23cms and 2mtrs tomorrow from one of the Lake district fells. Mainly to work Andrew G4VFL/P, but happy to work anyone.

I'll have Zello, but internet is flakey on Kirkby Moor, so a Text may be better 07955635646.

Nick G0HIK


Re: Looking for a 1N78BR detector diode

Rien Eradus PA0JME
 

Hi Arved, found 1N78BAR in my "junkbox" sealed in lead shroud, usefull?

My guess the R is for reversed, I did not test it with an ohm-meter since these diodes are known to be fragile.

I kept them for possible 24 GHz experiments, made my first qso there with Hans PA0DBQ, next month 40 years ago hi

Nowadays more modern stuff is at hand.

Best regards Rien

Op 14-9-2019 om 23:17 schreef Arved M0KDS:


Here are some pictures of the diode itself: 





Re: Millimetre Contest 15th September

Roger Ray
 

Slight change of plan.
First location IO91BL16 Clyffe Pypard
second IO91CL35 Hackpen
third if possible. IO91DL68

talk back 144.390, kst, mob: 07900 261121
Difficult to predict moving times, although only expect to be at the first location for an hour or so.

Roger
G8CUB


Re: milling copper

DougF VK4OE
 

Greetings to all.

My experience is that I have met my copper drilling/tapping/milling needs by way of purchase of drill bits, taps and milling cutters which are intended for use in cutting copper.  They do exist!  They also are great when trying to work with brass, some alloys of which are tough and likely to break whichever tool is in use.

FWIW.....

--Doug Friend, VK4OE.

On 15/09/2019 3:51 pm, Mike Willis wrote:
Best solution, find someone else to do it who can do it properly. Otherwise you get a poor finish, or a tap breaking and getting stuck just as you tap the last of 20 holes.
Mike G0MJW


Re: milling copper

Mike Willis
 

Best solution, find someone else to do it who can do it properly. Otherwise you get a poor finish, or a tap breaking and getting stuck just as you tap the last of 20 holes.
--
Mike G0MJW


Re: milling copper

Peter G3SMT
 

Hi Geoff,

Not sure which type is better but I have found that lubrication of the cutter with either kerosene or white spirit improves the cut and reduces the "stickiness" of the copper.

73

Peter    G3SMT


On 14/09/2019 22:12, geoffrey pike via Groups.Io wrote:
Is it any better to use a 2 flute mill instead of a 4 flute end mill to cut slots in copper plate
said slot is for LDMOS device to be soldered in,
cheers
Geoff
GI0GDP

--
Peter G3SMT


Re: milling copper

Neil Smith G4DBN
 

I use a 2-flute polished (uncoated) slot drill. With a 10mm cutter, I run 1200rpm and 75mm/minute, with WD40 lubricant.  I have used a three-flute carbide end mill as well, but the fast-helix cutters designed for high-rate machining of aluminium work best for me.

Top trick though is to avoid C101 and use C111 (or C109 if you can find it). C111 machines with nice short chips, doesn't tear, isn't gummy and doesn't build up on the tool edge like 101.

Neil G4DBN

On 14/09/2019 22:12, geoffrey pike via Groups.Io wrote:
Is it any better to use a 2 flute mill instead of a 4 flute end mill to cut slots in copper plate
said slot is for LDMOS device to be soldered in,
cheers
Geoff
GI0GDP


Re: Looking for a 1N78BR detector diode

Arved M0KDS
 


Here are some pictures of the diode itself: 




13241 - 13260 of 64937