I tried JLCPCB and was well pleased, however can i ask what you all use to design your pcbs, i have been brought up with Sprint but wonder if something else is better, however i'am not sure i want to learn Kicad. i don't need schematic capture

cheers

Geoff

GI0GDP

On Saturday, 2 July 2022, 11:57:53 BST, Andy G4JNT <andy.g4jnt@...> wrote:

Ok All, tnx

I've placed a test order with JLC PCB as they seem to be the one most mentioned here.   I didn't compare any of the others - that may come later with another test.

The price really was ridiculous at $2 for my 5 35x70mm boards - pity the delivery charge was very much more :-(

The speed with which the uploaded Gerbers were shown as a view was really quite impressive.   PCB Train / Newbury never offered that instant view facility

Lets see what arrives in a few days / week or so

Andy

www.g4jnt.com

On Sat, 2 Jul 2022 at 08:50, Dave - G4RQI <io93ir@...> wrote:

I've only used JLC PCB twice in 2021 and I thought the quality and service was excellent. My first batch of boards designed in Kicad were uploaded on a Saturday lunchtime and thanks to DHL arrived at my door on the Thursday. The 2nd batch took a couple more days but it’s still good service.

David -G4RQI

Get Outlook for iOS

---

From: UKMicrowaves@groups.io <UKMicrowaves@groups.io> on behalf of Lou Blasco <vk3alb@...>
Sent: Friday, July 1, 2022 10:36:30 PM
To: UKMicrowaves@groups.io <UKMicrowaves@groups.io>
Subject: Re: [UKMicrowaves] Low volume PCB manufacture

 

I use Seeed and find the quality great. In batches of 10 to 20 small boards the cost of manufacture is almost insignificant compared to the shipping costs. Still, at 1-2 dollars per board landed cost I'm happy with the service.

 

Regards

Lou

VK3ALB

On Sat, Jul 2, 2022 at 4:50 AM Colin G4EML <colin@...> wrote:

I have done a lot of orders, both large and small, with PCBWay and have never had a problem. 

Quality is excellent. When I have had a query the customer service has been good. 

I always opt for DHL delivery and the boards normally arrive in about 10 days. For a small order the delivery can cost more than the boards but the total cost can still be reasonable. 

Colin G4EML. 

On 1 Jul 2022, at 17:50, Andy G4JNT <andy.g4jnt@...> wrote:

As much as I prefer to make my own PCBs, it's about time I tested out the low volume low cost commercial jobbies.  So  I've laid out a test board (*), digital and audio frequencies, ready to give one of them a try.   It's double sided with plated through holes, although the underside is just a ground plane.   Needless to say, all SMT components.

What PCB manufacturers do people use when you only want a 'few' off at any time?  WHo has any experience; good or bad, delivery times, cost etc? Based on responses here I'll try out the one that looks most suitable.

This is more of an experiment to see what low cost commercial suppliers can do.

(*)  The PCB is a for a PIC used as a low frequency DDS, programmed via either a slowed down SPI bus, or generating one of up to 128 prestored frequencies using parallel addressing.  The dual quadrature sine output is generated from its onboard PWM generators.   The output is a baseband I/Q pair from [minus] -2800Hz to +2800Hz, delivered as a pair of differential lines for direct connection tio a quad upconverter chip. DC coupling is used throughout so it won't suffer from any holes in the middle of the output waveform  On board resistors are selected to optimise drive voltage levels to whichever DUC chip is used.

Being a PIC, it can of course be programmed to do anything else.   This code generates based on a 1024 bit sine lookup, with 10 bits of amplitude.   A third order opamp antialias filter removes clock and alilas components

Andy

www.g4jnt.com