I just joined this group. I've had a 2215 since new, but recently picked up an 2465 at an estate sale. It "works", except that the "world's most complicated fan" is dead. (I didn't realize this, and w

I know this is not on topic. I wanted to say how humbled I was to have a professor from Stanford ask me about the failure of parts. Someone of his stature, knowledge, skill, employment. etc. made me f

Hi all, I just finished to fully reconditioning my beloved 564. Fully recapped, a new CRT from a more recent 564B (with good efficiency), and all tubes replaced (the original from 1968 were still ther

I have a 475A power supplies are good I am trying to do an alignment on it when the scope is cold it runs all right for a while then all sweeping and triggering stops. Power supply voltages are good a

Has anyone pulled the battery/batteries from a DS1650Y used in TDS544A and other TDS's and if so remembers if it is done from the top or bottom ? /Håkan

Hello, I'm new to the group. I'm a railroad signalman, though I used to be a Simpson meter technician, and I'm still a ham and electronics tech. My major passion is antique radio restoration. I recent

One of the 5600pF feedthrough capacitors in the line input filter of my 7514 developed leakage sufficient to blow the line input fuse. Unfortunately, that capacitor is not an individually-listed part

Hi all,ive just brought a 465+DM44 for spares or repair,the seller says the trace will only adjust to halfway across the screen,any ideas where to start looking?.TIA.

I have for sale two brand new Tektronix 7D15 Counter Timers in original Tektronix packaging. Details are here: https://groups.io/g/Test-Equipment-For-Sale-Wanted-or-Exchange/message/3289 Contact me of

Hi, Does anyone have a scan for the Tektronix 465B vertical mode switch board A5 schematic. This is denoted as sheet <4> but is missing from all the online scans I can find. Attempting to chase a shor

Greetings, all --- I've just joined the group. I have recently acquired a mostly-working 492p --- unusual test-gear for a hardened computer-wizard, but I' retuired now, and it looked like fun! Initial

"My recently-acquired 576 seems to mostly work, save for some very dirty contacts in the pushbutton switches. But I noticed an irregular horizontal "throbbing" in the curves. Looking around a bit, I f

Hello all, I have a AA501 plug in that's missing all its plastic retaining latches on the side covers. The side covers use the same light grey 1/4 turn retaining latch that all TM500 series plugins ha

Hi guys, Another question for you on my TDS540 repair mission; When switched on from cold the traces are all off the bottom of the screen, but the trace indicator icon is in the right place. Over the

Does anyone know, where this https://groups.io/g/TekScopes/album?id=276319 unknown CRT impl. shield fits, or what Tek number it has? Dimensions: 4,791×3,998×0,100″ (121,70×101,55×2,55mm) (Doesn't fit

Hi all, I acquired a 7L13 in a 7613 frame in an unknown state. After replacing the electrolytic bulk capacitors in the 7613 PSU the spectrum analyzer is now partially working. So far I have identified

Ken, I would be interested in buying the Tektronix AFG5101 and PS5010. I'm in Southern California; Paul de Jonckkheere 16160 Suttles Drive Riverside CA 92504 Thank you, Pual 951-279-3750

Hello everyone, I am working on getting my Tek 495P and 2753P Spectrum analyzers fixed, running and calibrated. Has anyone here used the Prologix GPIB configurator by KE5FX (John Miles) to talk to the

Ballantine 6125B oscilloscope calibrator option MOD 14. Unit is in excellent condition. Great scope calibrator that covers everything except fast rise pulse and leveled sine wave. It works well, pleas

Tektronix PS5010 power supply for sale, very good cosmetic. Unit is untested. Photos on request or see ad in Test equipment for sale group Asking C$95 or best offer plus shipping from Vancouver, BC