There is a 2466BHD for bid on the auction site; seller is in Nara, Japan. I've never seen one of these for sale before, only read about them on TekWiki. The auction title is "Tektronix 2466BHD HDTV SC

I purchased a 7514 with, among other plugins, a 7B50 and 7B51. After noticing the sweep speeds did not track correctly in the 7B50 and inspecting the cam's leaf switches, I noticed that a few of them

Starting a new thread as although this is on the same scope, this is a different question and I want to avoid another long thread. I looked in the 455 service manual and in the Tektronix 'Troubleshoot

Tektronix 7F10 optical-input vertical plug-in, 700 nm to 1550 nm optical wavelength Optical bandwith 10 kHz to 750 MHz in a 7104, and works in78xx, 79xx mainframes. Detailed info on TekWiki. Scarce to

After successfully calibrating my 2465B, it reports "All tests passed" on start up. The question marks are all gone! My issue is with the parametric measurement of frequency. When I attempt to measure

I have a 5440 in my collection that happens to be an "option 01" scope. That is it doesn't have CRT readout. The controls for readout are on the front panel. However, the readout circuit board and som

I have just acquired a 2467 in very good cosmetic condition both internally (I'd even say pristine!) and externally, but it falls over at switch-on. Front panel lights flash on, then off and the TRGD

Entra? -- El software de antivirus Avast ha analizado este correo electrónico en busca de virus. https://www.avast.com/antivirus

asdfghjk -- El software de antivirus Avast ha analizado este correo electrónico en busca de virus. https://www.avast.com/antivirus

Hello all: I have a TEK 7L5 with tracking OPT 25 in Paris. I need to test it out, but I have no mainframe...Anyone in or near Paris that has of know of a working 7000 eg 7603, 7704? We could RDV meet

A few 475's and 475A's have landed on the bench of healing to see if I can breath life in to them again. I am starting with a unit that was owned by IBM and has the DM44 on the top. cosmetically the u

I came across these 11A32s. Are they pre-production? https://groups.io/g/TekScopes/album?id=275323

I noticed my 547's square wave response had deteriorated. There was a large long-duration overshoot, risetime had slowed from 7ns to 10ns, and bandwidth was 35MHz instead of 50MHz. There was no change

Hi all- just acquired a 2335 ( cute little bugger, excellent cosmetics), no raster, all voltages good( no ripple), except problem on the a15 board Z axis, near TP130 voltage was wrong, problem found-

I've been pondering asking this question for I know this is likely to be a "new to curve tracing" question but here goes. For reference, pictures here: https://groups.io/g/TekScopes/album?id=252850 Fo

After years of wanting one, I've finally bought a 576 which I believe is currently sitting in customs 20 minutes from my place. Like quite a few people out there I'm mainly planning to use this for me

On 2022-05-21 4:25 p.m., toby@... wrote: > Hi all > > I have a loose 604 crt so I thought I'd ask on the offchance that > someone has a 604 parts unit - hopefully lacking little more than the > crt, b

I just acquired a Tek 3001GPX with all the goodies (keyboard, three P6490 acquisition probes, and 2 extra probe lead assemblies for the P6490s). It powers on, passes all it's self tests, says that it

Hi all, I have come across a Tektronix/Sony CM360 Oscilloscope Checker and was trying to find any manuals or information on this equipment. Unfortunately, the internet seems a bit lacking in any real

Hi all, I've recently purchased a 7A16A, working, looks new, S/N B138015. Probably the previous owner has tried to calibrate the HF response in a badly manner: risetime was 3 ns with very rounded fron