The following files have been uploaded to the Files area of the TekScopes@groups.io group. /EIP 101A_201A Ops_Svc OCR.pdf By: ChrisBeee <chrisbeee@...> Description: searchable Operating and Service ma

Hi all, I'm thinking of building my own version of the 067-0625-00 Peak-to-Peak Detector, and I am hoping someone has one that they can take a few decent photos of each side (maybe even with a ruler f

Hey y'all, I have a 2465 (in-line for recap) and a 2467. At some point there was a 2467B that came up for sale locally, which was tempting. However, after looking at the differences between my 2467 an

I have TM506 that I have had for some time. I have a PG506 that works but it shows terrible distortion on the top and bottom of the square wave when installed in any compartment the TM506. Just as a t

Anyone had to locate replacement batteries for this unit. Only marking on the battery is 1A. Original Tektronix description is: 1.5V, 650MAH, Alkaline-Manganese Dioxide Tektronix 067-0625-00 Peak to P

What do you guys think of this curve tracer compared to other “real” Tek ones? What would it compare to in the official Tek line? Is it worth it? I’ve never used a curve tracer before, and I don’t own

Rebonjour a tous: Same low SN B062 2465B has extrême CH1,2 compression on lower part of display. CH 3, 4 are perfect and normal. Photo Album: 2465B CH1,2 compression Taken with 100 kHz triangle on CH

I have noticed that much of the Tek gear we all seem interested in has no electrical safety approval of any kind. the same is true for HP gear. at what point did Tek actually incorporate equipment saf

https://www.ebay.com/itm/Tektronix-6R1A-Nixie-Tube-Display-tubes-sockets-biasing-resistors/143944707131 I guess someone is parting one out... the destructive way... You certainly won't be recovering t

I just joined here, having been a member of Yahoo! group some years ago. After checking with the moderator, apparently I am allowed to post that I have a 7854 working scope with 7A26, 7A16P, 7B80 and

Hello, Does anyone know the chemical composition of the dark deposits on IC pins that are close to leaking SMD caps? What is the best way to clean them? Litmus paper shows base (hard to tell because i

Here is a 1A5 in a 132 for $85. Looks pretty nice but no pictures of it working. Still a good price. https://www.ebay.com/itm/Tektronix-1A5-Differential-Amplifier-in-a-Tek-132-Power-Unit-Vintage/32448

I have a 465B that is looking good and running well, except that the coupler for ch 2 amplitude var coupler is broken. Check these two tweets in a twitter thread for images of the broken part includin

Hi all, just joined. Owner of a Rigol 1054z, satisfied user for what I am currently doing (especially for the price!) . Being a 50/100MHz with 1Gs/s bw scope, I wanted to explore other options to incr

Hi all, I don't know if I made a mistake during alignment or if I just didn't notice it before, but the step generator is no longer working properly. In NPN mode it gives a constant +30V, in PNP it lo

Hi folks, I have 2445B for quite many years, thanks to this awesome group and some super helpful members like Siggy or Chuck and others I dealt with leaky caps on the A5 board, backed up and copied ca

Hello I am new to this group. Recently I restored 2465B and which works well. While fine tuning the CRT focus and I notice following things. CRT cathode volt of mine is -1960V which higher from schema

Since I'm going to be working on this 3T77A plug-in for a while, an extender is necessary. Some years ago I acquired a pair of Amphenol connectors with the intention of building my own extender, but n

I’ve just realized that for a long time I’ve been using 75ohm-20’´ long coax for my calibration procedures are for mostly everything when coax cables are required. I trusted the place I bought these f

Hello, I just spotted some TDS5054B-NV-AV variant of the TDS5054, but after some googling it seems I can't find any information about what that NV-AV variant is about... Anyone can shed some light on