Hi Bill , Imagenation are the guys that produced the cards I have , CX100 is the ISA card I have used and PXC200 is the PCI card , now replaced by the PXC200A . The software drivers etc are all still

Hi Bill , I have several of these video camera's but not the Tek frame grabber or software . I have a Cortex frame grabber which works very well and some Cortex s/w available on their website some yea

Hi Michael and others on this thread , just to add my few pennies worthSeveral years ago when postal charges were more reasonable I bought over a short period 3 Tek 7k scopes 7854,7834 and a 7104 from

Hi Bruce , I would join . My logic analysers are all very old . 308 , 7D01 , 7D02 and DAS9100 also HP1615A so would likely need more help than I might be able to give ;I dont have enough free time to

Hi Raymond , I have several 7A19's and so far not blown one of the input fuses , I hope I dont ever as I gather that they are rather hard to find , fortunately all the 7A19's I have purchased have had

Hi Raymond , I have a couple of TDS's , a 744 original version and a 420A . Both are protected on the 50R input setting so I would expect all others to be the same . I have noticed this behaviour when

Hi , sorry to but in but I think Tek have got it right . The scope has no idea if the voltage measured is from a hi-impedance current limited source or a low-impedance constant voltage source with lit

Hi GerhardMine does the same , or it did before the power supply went into tick mode , not had time to fix that yet . I put it down to expectations of a bi-stable screen like that in a 564 or a 549 bu

Hi Dan I have downloaded a copy of the Define Mnemonics section 7 . It has pointed the way through what I was thinking was some kind of fault having developed on my DAS . The menu's I was seeing did n

Hi Dan Thankyou for letting me know its there . Sneaky addition to the command set that shift key . I have V1.11 in my DAS and I have been worried that something was wrong as the Define Mnemonics menu

Hi Dan Refering back to my original problem with the DC100A cartridges , I am beginning to wonder if they were just too cold when I put them in the drive ? . The room temperature might have been quite

Hi Dan I have just looked at my spare A2 pcb its an -02 as yours is and it looks like the same connections are made . I have not looked at the service manual or removed the heatsink plate from the bac

I have seen on Ebay scopes that have smasked bezels around the crt and broken knobs etc , to say nothing of scratches and dents in the cabinet -- described as GOOD CONDITION ?????? I wouldnt have the

Dan , a miss-type in my mail -- 7D20 should be 7D02 Brian

Hi Dan , nice to hear from you . I hope you are well and avoiding this virus . I was surprised at how easy it seemed using GPIB with the DAS , mush easier than with some early instruments . The damage

Hi Dan ,as a result of your last message I have looked elsewhere for a user manual for the DAS , bitsavers were a good choice . The copy I had was incomplete , section 12 was only about 25% complete .

Hi Dan , I will re-read that section of the manual . When I read it before I got the impression that all the mnemonics command did was read the data from the tape in the drive and acqmem again involve

Hi , I have some experience taking waveform data via GPIB from my 7D20 and also interfacing with my TDS744 and TDS420A . The main problem with the DAS9100 is that none of the manuals I have actually s

Hi Dan , I'll be most grateful for any information regarding use of the RS232 or GPIB ports for data transfer . I have only the one DAS so my hope is purely to be able to save setups and pnemonic file

Hi Raymond , I found the group on groups.io and I have also found the articles covering the DC100A cartridges , many thanks for that . Brian