with the FG 504 set at start freq 10, stop freq 40, multiplier at 10^2, sweep off, measured on my 2445b, Sine freq 982.3 Hz, Sawtooth 975.9 Hz and Square wave 24.5 mHz. The square wave is an

HI! A german Tektronix fan constructed three plugins: 1) RO510 10MHz Rubidium Oszillator. Two protoypes were built. http://w140.com/tekwiki/wiki/RO510 2) DP512: A 12GHz 1:1000 prescaler. One

I’m not sure about folks outside of the US but if it were me I’d take a side panel down to the paint store and have them color match it. I’ve used this method on my house where it works well,

I believe at one time a company called Spectracom built a TM500 rubidium frequency standard plug-in.

Yes, and no... You know what the values should be, and you know relatively where they exist in the calibration file, but you have no idea how, or where, they exist in the 2K RAM. Tektronix went out

I am interested in the 7J20/J20 for light source spectrometry. I have an Ocean Optics fiber-optic one that works for what I usually need, but hey, one that works with my Tek 7000-series scopes would

What exactly don't you understand about the Bluebase 79126 reference? I am guessing here, but I think you might have a difficulty in understanding the technology of making a particular color

It takes a brave person to admit to liking and using an 11k-series scope :) I have a couple and "like" them in remote-controlled applications, but hands-on operation is a different matter. The

Here’s a quick review of what’s important to know about the wide assortment of scopes and scope features available today. https://prezhost.com/2020/06/25/how-to-select-an-oscilloscope/

Hi guys! I opened exerciser 2 on my scope and copied all the data from 00 to ff by looping through all of them as I was recording a video. If I input the said data in my programmer and flash a new

There has been communication on Tek blue paint ever since I joined this Forum. May I respectfully suggest that you have a search through the past posts to find all you can. There is a lot of

Hi Dave, Abc Xyz did not report back so far, so the scope can be yours. I will send you a PM to clarify details. Chris @Abc Xyz: Sorry, but even in 'modern' times where salutations and signatures in

I notice something I didn’t pay attention to before. That is TP1486 should go from 15V to 75V depending on the position of the Intensity control knob. However, mine goes from 15V to only 31V with

Hi to All, Inspired by the 7J20 and J20 scarcity remarks.There are other items. Seldom seen. Sometimes only once. Recently many overpriced 067-XXXX-99 Fixtures pop up on eBay and also TekWiki has a

I think if you find one of those, that it will be protected by unicorns. According to Dennis Tillman in TekWiki, there were only about 40 made. If I understand correctly from past discussion on this

Hello Saroj, Another thing popped into my mind: Before putting the transformer back, if you have another scope and a sine generator, you could verify the fase of the windings. And another

Hi Saroj, Could very well be. The Kaptan comes as sheets of foil, as self adhesive tape, etc. I believe it's also used as solder mask and as protection during manufacturing. See this partial wiki

Digikey lists it as available in tape form. YMMV In matters of style, float with the current. In matters of Principle, stand like a rock. “. — Thomas Jefferson —

Hi Joe, From a German eBay Member (I assume a former Tektronix Germany employee) I got the following answer: "Guten Tag, ja ich weiß es, es sollte mal einen Eigenbau eines Prescalers bis 14 GHZ

Hi Satbeginner Thanks for the information. Is kapton a sheet that we put in the pcb to protect components while hot airing the pcb? To day I put the 1-2 winding. The number of turns came out to be