Date   
tpp1000 on 2465b

James Theonas
 

is the tpp1000 probe compatible with the 2465b?
Thanks to everybody!

Re: tpp1000 on 2465b

John Williams
 

It looks like a $1000+ 1ghz probe might be overkill on a 2465b. However I see no reason why it wouldn’t work.

Re: tpp1000 on 2465b

David DiGiacomo
 

On Sat, Nov 16, 2019 at 11:58 AM James Theonas via Groups.Io
<jamestheonas=yahoo.com@groups.io> wrote:

is the tpp1000 probe compatible with the 2465b?
No, there would be no way to adjust the compensation.

(Not that the compensatable scope input capacitance range is specified.)

Re: Air filters for 500 series.

Keith
 

My 5 series Tek appears to use a very typical 45w Howard Industries fan. These are nothing but glorified refrigerator evaporator fans, and equivalent models are still commonly available.

It looks to me like it would be easy to up the motor wattage a notch while staying in the same frame size. One could then pitch the OEM aluminum fan blades a little steeper by hand (not that hard to do - I've done it on other fans) and maybe tighten up the dimension of the fan flange with some plastic trim or something similar. (That's where the efficiency of these fans really suffers, and the tighter the fit, the better the efficiency. Of course, if the bushings get loose, a tight tolerance fan will hit, but hey...that's why you're supposed to replace those bushings when they "become worn" just as it says in the manual. :-)

FWIW, if anyone is experiencing inadequate airflow, IMO it would be pretty easy to gain 15-20% airflow increases while keeping an original look by doing these or similar steps.

Filter oil - yeah, ditto on the K&N oil. Works great as long as it lasts, which is quite a while in reasonably clean environments.

Finally, similar shredded wheat metal filter material is available from restaurant supply houses. (Grease traps use a similar material) and the C channel that makes up the filter frame is common as well. This, just in case someone wants to fabricate a "near correct" filter for their 5 series. FWIW

Cheers

TEK 494P 1st LO mixer

kmatus4365@...
 

Hi to all members of the group. I'm new here though I have read many post in silence. Today I turn to you b/c I am looking for a 1st LO mixer 119-1017-00 or, alternatively for a 119-1353-00. No way to get one here in Vienna/Austria. Any replies greatly appreciated. Karl

Re: TEK 494P 1st LO mixer

John Williams
 

Hi Karl glad to see you here. I can’t help you,but hopefully someone in the group can. Regards, John

Re: Air filters for 500 series.

Chuck Harris
 

Overheating of the 500 series scopes, including the 555, was not
a problem. Not at all.

Overheating of the lab the scope was in, well that was a different
story.

Why fix it if it isn't broken?

Your mod may increase the airflow, assuming the filter isn't so
restrictive that the fan is working up against a wall, but it
will also increase the noise. Something most people don't need or
want.

You say that the fan is nothing but a glorified refrigerator
evaporator fan, given that tek spec'd these fans in the late 1940's,
and late 1940's refrigerators didn't have evaporator fans, are
you sure that refrigerator evaporator fans aren't really nothing
but glorified oscilloscope fans? ;-)

-Chuck Harris

coolblueglow@... wrote:

My 5 series Tek appears to use a very typical 45w Howard Industries fan. These are nothing but glorified refrigerator evaporator fans, and equivalent models are still commonly available.

It looks to me like it would be easy to up the motor wattage a notch while staying in the same frame size. One could then pitch the OEM aluminum fan blades a little steeper by hand (not that hard to do - I've done it on other fans) and maybe tighten up the dimension of the fan flange with some plastic trim or something similar. (That's where the efficiency of these fans really suffers, and the tighter the fit, the better the efficiency. Of course, if the bushings get loose, a tight tolerance fan will hit, but hey...that's why you're supposed to replace those bushings when they "become worn" just as it says in the manual. :-)

FWIW, if anyone is experiencing inadequate airflow, IMO it would be pretty easy to gain 15-20% airflow increases while keeping an original look by doing these or similar steps.

Filter oil - yeah, ditto on the K&N oil. Works great as long as it lasts, which is quite a while in reasonably clean environments.

Finally, similar shredded wheat metal filter material is available from restaurant supply houses. (Grease traps use a similar material) and the C channel that makes up the filter frame is common as well. This, just in case someone wants to fabricate a "near correct" filter for their 5 series. FWIW

Cheers



475 repair parts

 

All,
I rescued a 475 the other day. I met the guy at a gas station and handed him 20 bux. It in the back of his pickup on top of a load of firewood. Anyway I cleaned it up and have a couple of caps on the way. One of the trigger level/polarity pots didn’t survive the ride. I’m looking for a 311-1192-00 trigger level pot with switch

Thanks
Chris W9RP

Re: Air filters for 500 series.

John Williams
 

Right Chuck I agree. Thee biggest reason for overheating was poor maintenance. The filter was often not cleaned properly, but I think that even a dirty filter would still pass enough air to sufficiently cool the scope. More likely was a poorly maintained fan motor. If the motor was not regularly or properly lubricated, that would lead to it gradually slowing until finally seizing. Then the technician would pour oil into the oil holes on the motor but it would be too late. Oil would run down and coat the rear of the scope, which would eventually become a dirt encrusted mess. The only solution is to remove the fan, disassemble the motor and clean the crap out of the bushings. I have worked on some that even this extreme repair didn’t fix. That’s where a few spares come in handy. I also notice the dirtiest scopes are usually only dirty from the top, underneath they are pretty clean. I don’t know why this is, it’s as though they sat in a basement with the covers off.

7844 power supply

Peter Gottlieb
 

A couple of weeks ago I mentioned a 7844 which instantly blew the line fuse but which had previously worked.

It was suggested I look at the line rectifier and bulk caps.

I finally finished the project on my bench and put the scope there. The problem turned out to be that the two main switching transistors were shorted.  After replacing them all was not well though.  The supply kept trying to come up, making a weak rattling sound.  I could see it was trying.  Then ever once in a while it would come up, fan run, and scope start, but then within a few seconds go back to rattling.  Then in the midst of considering where to look next it just stopped.  Now, nothing.  HV is on the main caps and the neon is rapidly flashing, but nothing else.

These supplies are infamous for being a pain in the neck.  Has anyone seen this and have any hints for what I should look for?

Peter

Re: 475 repair parts

Jamie Ostrowski
 

Ha, such strange stories. One of my 535's was delivered to me in the bed of
a pickup truck, un-anchored. SMH...

On Sun, Nov 17, 2019 at 11:53 AM n9llo via Groups.Io <N9LLO=
aol.com@groups.io> wrote:

All,
I rescued a 475 the other day. I met the guy at a gas station and handed
him 20 bux. It in the back of his pickup on top of a load of firewood.
Anyway I cleaned it up and have a couple of caps on the way. One of the
trigger level/polarity pots didn’t survive the ride. I’m looking for a
311-1192-00 trigger level pot with switch

Thanks
Chris W9RP



Re: 7844 power supply

Ed Breya
 

The last time I fixed a 7844 PS, it was fortunately just two or so rather large (100 or 220 uF 20V) Ta caps shorted, on the pre-regulator supply board, for the +/- 15V inside the PS module - the one inside the cage, just below the outer, upper, linear regulator board. It's a PITA to get to, but doable - if you take enough stuff apart, you can run it while opened up and make measurements. The fix is fairly straightforward, but there's very little space, so you'll have to get creative with alternative cap arrangements. I manged to do all the work from the component side, avoiding having to remove the board, which is even more a PITA.

If it's not those or something else like another Ta cap in the scope circuits, it could be the dreaded HV winding failure on the main transformer. Hope for the lesser grief.

Ed

Re: 7844 power supply

Peter Gottlieb
 

I looked again and one of the switcher transistors failed again so replaced that. Now back to burst operation.

The switcher shutoff is coming from the control chip. It seems to be triggered by large spikes coming in on the balance input and those seem to be coming from the current sense on the HV side. This might be caused by a shorted HV diode or the multiplier. I am hoping it is not the HV winding as that would likely mean scrapping of this otherwise mint scope, but the indication is promising (at least right now).




Peter

On Nov 18, 2019, at 12:50 AM, Ed Breya via Groups.Io <edbreya=yahoo.com@groups.io> wrote:

The last time I fixed a 7844 PS, it was fortunately just two or so rather large (100 or 220 uF 20V) Ta caps shorted, on the pre-regulator supply board, for the +/- 15V inside the PS module - the one inside the cage, just below the outer, upper, linear regulator board. It's a PITA to get to, but doable - if you take enough stuff apart, you can run it while opened up and make measurements. The fix is fairly straightforward, but there's very little space, so you'll have to get creative with alternative cap arrangements. I manged to do all the work from the component side, avoiding having to remove the board, which is even more a PITA.

If it's not those or something else like another Ta cap in the scope circuits, it could be the dreaded HV winding failure on the main transformer. Hope for the lesser grief.

Ed


Large set of Tektronix parts for sale

Jamie Ostrowski
 

I ran into this ad. I am not associated with the seller in any way. I just saw this ad and thought that someone may be interested...

Location is Milton, NY. $1000 for all:

https://www.facebook.com/marketplace/item/2423409567986774/




to much to list here is some of it
The following is a list of electric parts for sale

5 201-0013-00
3 310-0600-00
3 311-0431-00 Tektronix Potentiometer Dual Concentric 50 K / 50K $8.50
Potentiometer Dual Concentric 50 K / 50K Tektronix Part # 311043100 3 [hidden information] Tektronix Trigger Level Slope Control 15.00 This is a replacement for the trigger level/slope switch control used on many Tektronix oscilloscopes, including the 400-series. These pots frequently become noisy, or the shafts are bent, or the slope switch stops working.

This is part number [hidden information]. It is a replacement for part number [hidden information], except that the bushing is 0.375 inches (3/8) long instead of 0.250 inches (1/4). Washers or a nut must be added behind the panel so that the bushing exposure on the front of the panel is the same as the original. There must also be an additional 1/8 inch clearance behind the pot. This clearance is present on many instruments, but please check your instrument for clearance before ordering.
5 309-0109-00
3 311-0258-00 Clarostat 100 Ohm 5.00
1 311-0283-00 1 311-0450-00 Potentiometer Hi Voltage 1 Meg Tektronix Part # 311045001 4 311-0026-00 Clarostat 100K Potentiometer 5.00 used
1 311-0297-00
1 311-1311-00 Bourns 81C1DE24BA0324 1k 16.00 6 [hidden information] Tektronix Trigger Level Slope Control Replacement for P/N [hidden information] This is a replacement for the trigger level/slope switch control used on many Tektronix oscilloscopes, including the 400-series. These pots frequently become noisy, or the shafts are bent, or the slope switch stops working. 15.00
8 290-0310-00 Capacitor, Fixed, Electrolytic Capacitance Value per Section: 2000.000 microfarads single section
Terminal Type and Quantity: 1 tab, solder lug Body Style: 2B W/twist tab mtg, terminal(s) on one end
1 281-0036-00 3 307-1023-00 TEKTRONIX 307-1023-00 DUMMY LOAD NEW IN BOX 10.00
4 311-1558-00 20K 1 311-1311-00 Tektronix VARIABLE RESISTOR 311-1311-00 S 8.00
1 311-0088-00 Resistor, Variable, Nonwire Wound
1 311-0285-00 Resistor, Variable, Nonwire Wound
1 311-0218-00 Resistor, Variable, Wire Wound, NON
1 310-0602-00 Resistor, Fixed, Wire Wound, Nonind
4 285-0749-00
1 310-0544-00 Resistor, Fixed, Wire Wound, Induct

1 308-0535-00
5 311-0066-00 pot comp 500 3.45
3 309-0103-11 res
5 309-0090-00 res 1 307-1011-00 Attenuator 4x NOS 5.00
3 309-0168-00 res
4 308-0176-00
3 308-0266-00 res
3 309-0180-00 res
5 309-0115-00 res
3 309-0049-00 res 1/2 w
6 309-0086-00 res
1 309-0030-00 res
3 309-0191-00 res
1 310-0537-00
5 309-0193-00

425 Allen Bradley resistor GB 1045 1 watt 100K OHMS 5.00 each .
500 Allen Bradley resistor GB 1035 10,000K OHMS 8546 1.50 each
2000 Allen Bradley resistor GB 1055 1 watt 1.0 Meg OHMS 8548
780 Allen Bradley resistor GB 1035 10,000K OHMS 8549 1.50
1000 Allen Bradley resistor GB 1045 1.0 Meg OHMS 8631 5.00 each
500 Allen Bradley resistor GB 1045 100K OHMS 8012

2 308-0315-00 Resistor,Fixed,Wire Wound,Inductive 5 283-0575-00 CAP MICA .01 UF 5.00
3 309-0196-00 Res
2 309-0199-00 Res
3 309-0245-00 Res
5 309-0181-00 Res
3 309-0197-00 Res
3 309-0125-00 Res
3 309-0194-00 Res
4 309-0195-00 Res
5 310-0596-00
5 308-0018-00
3 310-0537-00
1 307-1013-00
5 309-0182-00 Res
6 309-0114-00 Res
2 310-0611-00
3 309-0007-00

1 260-1037-00
1 262-0595-01
8 262-0417-00
1 262-0561-00

200 EB 1015 Allen Bradley resistor 1/2 Watt
100 EB 1045 Allen Bradley resistor 1 Watt

20 1802C Wire Bound Resistor 20 Watt 3.00 OHMS











2 311-0386-00 control Potentiometer Precision 10 Turn 2K 5% Lin = .1% - Tektronix Part # 311038600 Potentiometer Precision 10 Turn 2K 5% Lin = .1%
3 311-1670-00 Potentiometer Dual Concentric 10K / 100K with Long Shaft - Tektronix Part # 311167000 Potentiometer Dual Concentric 10K / 100K with Long Shaft $23.50
1 311-0431-00 control Potentiometer Dual Concentric 50 K / 50K - Tektronix Part # 311043100 Potentiometer Dual Concentric 50 K / 50K 8.50
1 311-0189-00 control
15 311-0190-00 control
1 311-0426-00 Potentiometer 300 KOhm With Switch - Tektronix Part # 311042600Potentiometer 300 KOhm With Switch 8.50
2 311-1701-00 control
3 311-1558-00 control 1.05
1 311-1273-00 control .70

Wanted: DPO7000 series probe pouch

 

Looking for a black, snap in place, probe pouch that goes on top of a DPO7000 series scope. Must be in very good condition.

Manuel

TDS3012B NVRAM

Ferenc Rózsa
 

Good afternoon for everybody,

I've got such a Tektronix TDS3012B scope and
run out the CR2032 coin cell in the NVRAM.
The type of the NVRAM is DALLAS DS1742W-120
So this is a 3.3V VCC, 2 KByte, JEDEC paralell programming NVRAM. Where can I buy it or which is the replacement type of this ?
This is 24 pin EDIP type.
Thank you very much for you help: Ferenc

Tektronix 7904, no horizontal trace on input B

Hermansson Amplification
 

I just bought a Tektronix 7904 scope and realized that something is wrong with horizontal input B.
Horizontal input A works fine but I got no trace on input B. If I press
“Beam finder” slightly I see dots for each inputs that are activated in the vertical slots and if I press the “Beam finder” harder I see bigger dots. I only see the dots when I press “Beam finder” otherwise the screen is blank when horizontal input B is activated.

Any suggestions where to start? I’ve measured the voltages on the Z axis-PCB but nothing alarming there. Since the horizontal Input A works something might be bad on the “Trigger B”-PCB? Or where should I start?

Here’s a video showing the problem:
https://youtu.be/KuPenOSkyJg

I’ve been exercising the switches and cleaned the input slots for the plugin.

Thank you in advance!

Best regards,
Henric

Re: Tektronix 7904, no horizontal trace on input B

 

Hi Henric,

The first thing I notice in your video is that when you put the time base in the B horizontal slot the 7904 recognizes it is present because it displays the on-screen readout time/div setting on the bottom right part of the CRT. That is a good sign.

The second thing I see is when you press the beam finder with the time base in the B horizontal slot the display you get shows there is no sweep present. You are just getting the vertical signals on the screen without any horizontal sweep.

There could be two reasons for this:
A) The time base is not getting a trigger signal when it is in the B horizontal slot. One test you can perform would be to feed a trigger signal into the external trigger input of the time base while in the B slot to see if this fixes the problem. If it does then that confirms the trigger signal is not getting to the B slot from the vertical amplifiers. That could be caused by a bad front panel B Trigger Source Switch or by the IC that controls the routing of this trigger signal which would be on the backplane PC board. Also on the rear of the 7904 (or maybe even on the front of it) there are several BNC connectors which bring out critical signals like trigger signals. If there is a B Trigger Signal output make sure it is present on the front or rear panel BNC connectors.

B) The time base is being triggered and generating a sweep but the sweep is not getting from the time base to the horizontal amplifier in the mainframe. Once again there are ICs on the back plane that route this sweep signal. The B Sweep signal comes out to one of the front or rear BNC connectors so you should check for it there. If it isn't there and if it isn't on the CRT the IC that switches it thru from the back plane to the horizontal amplifier may not be getting the right switching signal or it may be bad.

The most important thing you can do for your own benefit and to learn how your new scope works is to read the Theory of Operation section of the service manual. It explains everything! For the moment read the parts about how the trigger signal is routed and how the sweep signal is routed to learn the various places they go in the scope and which ICs they go through to get a better idea of exactly where to look for where it is being blocked.

Dennis Tillman W7PF

-----Original Message-----
From: @HermanssonAmplification
Sent: Monday, November 18, 2019 7:06 AM
Subject: [TekScopes] Tektronix 7904, no horizontal trace on input B

I just bought a Tektronix 7904 scope and realized that something is wrong with horizontal input B.
Horizontal input A works fine but I got no trace on input B. If I press “Beam finder” slightly I see dots for each inputs that are activated in the vertical slots and if I press the “Beam finder” harder I see bigger dots. I only see the dots when I press “Beam finder” otherwise the screen is blank when horizontal input B is activated.

Any suggestions where to start? I’ve measured the voltages on the Z axis-PCB but nothing alarming there. Since the horizontal Input A works something might be bad on the “Trigger B”-PCB? Or where should I start?

Here’s a video showing the problem:
https://youtu.be/KuPenOSkyJg

I’ve been exercising the switches and cleaned the input slots for the plugin.
Thank you in advance!

Best regards,
Henric




--
Dennis Tillman W7PF
TekScopes Moderator

465B soft start?

treasurer@...
 

Is there much to be gained by powering up my 465B with a variac, lamp dimmer or similar arrangement? It popped (shorted) its 1200 ufd C4429 at power on recently. This cap does not have much head room with its 100 volt rating and 70 volts sitting on it. I'm thinking a soft power up may help prolong the life of those caps. Any thoughts or past experience from the group using this power-on approach?
Bruce

Re: 465B soft start?

Tom Gardner
 

Switching power supplies operate to keep the output power constant.
Hence if the input voltage is lower, the input current must be higher.

Increased current stresses components such as the rectifiers and
switching transistors.

On 18/11/2019, treasurer@... <treasurer@...> wrote:
Is there much to be gained by powering up my 465B with a variac, lamp dimmer
or similar arrangement? It popped (shorted) its 1200 ufd C4429 at power on
recently. This cap does not have much head room with its 100 volt rating and
70 volts sitting on it. I'm thinking a soft power up may help prolong the
life of those caps. Any thoughts or past experience from the group using
this power-on approach?
Bruce