|
over deviation of D710A APRS mode at 9600 baud: reducing deviation 5 messages
I have a TM-D710A which I am using for APRS. I am testing it at 9600 baud. Using my deviation meter, it looks like it is over deviating and it can not be decoded by a D710GA, D72A, or a component base
I have a TM-D710A which I am using for APRS. I am testing it at 9600 baud. Using my deviation meter, it looks like it is over deviating and it can not be decoded by a D710GA, D72A, or a component base
|
By
Don Rolph
·
|
|
D710A/V71A transceiver body: failure of transmit under extended use: is this a known issue?
I have a D710A. We were using it in a public event. After about 9 hours of net control use, transmit failed. We attributed it to a high SWR in the antenna and replaced the transceiver unit. We were us
I have a D710A. We were using it in a public event. After about 9 hours of net control use, transmit failed. We attributed it to a high SWR in the antenna and replaced the transceiver unit. We were us
|
By
Don Rolph
·
|
|
How to know if TM D700 ":sees" the computer 5 messages
Most of my radios require I take action for it to connect to the computer. I find no instructions in the two D700 manuals on that. When I plug in the serial port, the radio and computer do not communi
Most of my radios require I take action for it to connect to the computer. I find no instructions in the two D700 manuals on that. When I plug in the serial port, the radio and computer do not communi
|
By
Bruce W4BRU
·
|
|
TM-D710G Password 11 messages
Has anyone figured out how to reset the power on password in the D710G? Here's what happened. I wrote my config to the radio with the password button checked in MCP-6A software. Now I realize the pass
Has anyone figured out how to reset the power on password in the D710G? Here's what happened. I wrote my config to the radio with the password button checked in MCP-6A software. Now I realize the pass
|
By
Joe B
·
|
|
TM-710A repairs... 11 messages
Hello everyone. I have been out of ham radio for many years, and when I stepped back in a fellow ham gave me a TM-710A that he said was a spare. It still had the film that covered the screen, and the
Hello everyone. I have been out of ham radio for many years, and when I stepped back in a fellow ham gave me a TM-710A that he said was a spare. It still had the film that covered the screen, and the
|
By
David McGuire
·
|
|
Hard reset; TM-D710...
Hello. It was suggested that I need to do a hard reset of the radio. In the owner's manual, page 33, it has menu 999, but will this do a hard reset of the whole radio? Under "setting values" there is
Hello. It was suggested that I need to do a hard reset of the radio. In the owner's manual, page 33, it has menu 999, but will this do a hard reset of the whole radio? Under "setting values" there is
|
By
David McGuire
·
|
|
Mini-DIN band? 3 messages
Greetings D700 enthusiasts (and hopefully an expert or two), Having read the D700 manual and the Specialized Communications manual, I cannot tell what sets the band used when a Mini-DIN-connected devi
Greetings D700 enthusiasts (and hopefully an expert or two), Having read the D700 manual and the Specialized Communications manual, I cannot tell what sets the band used when a Mini-DIN-connected devi
|
By
Lynn Deffenbaugh
·
|
|
TM-D700 problem 5 messages
My D700 has developed a problem. When I turned it on today the message on the control head read the following PROG 115200 bps, Trying various buttons etc made no difference. Anyone had this problem or
My D700 has developed a problem. When I turned it on today the message on the control head read the following PROG 115200 bps, Trying various buttons etc made no difference. Anyone had this problem or
|
By
John
·
|
|
station list / packets 'heard' 2 messages
Hey everyone. I'm new to this forum. I've had my Kenwood TM-D710GA for a few months. It basically functions as my base station, but I like to play with APRS...and especially the messaging. I've had it
Hey everyone. I'm new to this forum. I've had my Kenwood TM-D710GA for a few months. It basically functions as my base station, but I like to play with APRS...and especially the messaging. I've had it
|
By
Tim Manwell
·
|
|
710 Crossband repeater
when using crossband repeat can the tm d710 id with morse on both bands ? (not locked band repeater) TIA OY1R
when using crossband repeat can the tm d710 id with morse on both bands ? (not locked band repeater) TIA OY1R
|
By
Regin
·
|
|
Can DXLab's "Commander" control the D710G Frequency? 13 messages
I (( still )) would like to be able to move the frequency of my Kenwood D710G around .... read it.... and so forth. The only control I have had so far, in a year or two, is AGWPE (packet engine pro) a
I (( still )) would like to be able to move the frequency of my Kenwood D710G around .... read it.... and so forth. The only control I have had so far, in a year or two, is AGWPE (packet engine pro) a
|
By
NR4U Bob AFMARS
·
|
|
TNC Transmit Problem 12 messages
I have a TM-D700A that I use for aprs and ham use. I use the the unit for standa-alone APRS and connecting to UI-VIEW in a mobile application. It has been working fine until recently I noticed that it
I have a TM-D700A that I use for aprs and ham use. I use the the unit for standa-alone APRS and connecting to UI-VIEW in a mobile application. It has been working fine until recently I noticed that it
|
By
Jason
·
|
|
D700 APRS mode Left Display shows busy 6 messages
I’m trying to set up my D700 for a Digipeter. I’ve followed the steps and the “A” channel is “busy”. Adjusting squelch doesn’t fix it. Any suggestions? I saw this problem discussed before but no one s
I’m trying to set up my D700 for a Digipeter. I’ve followed the steps and the “A” channel is “busy”. Adjusting squelch doesn’t fix it. Any suggestions? I saw this problem discussed before but no one s
|
By
George Miller W3GWM
·
|
|
D700 APRS Send 2 messages
I'm receiving packets from other stations, but I don't think I'm transmitting data. I see the Xmit key, but when I look on APRS.FI I see my weather station but not my APRS from the D700. Any ideas?
I'm receiving packets from other stations, but I don't think I'm transmitting data. I see the Xmit key, but when I look on APRS.FI I see my weather station but not my APRS from the D700. Any ideas?
|
By
George Miller W3GWM
·
|
|
s-meter reading? 6 messages
This is going to sound like a really silly question but how to you read the s-meter on a TMD700? Generally, a S-meter will have 9 levels. My Kenwood TH-F6 has 9 bars. But on my TM-D700 it only has 7 b
This is going to sound like a really silly question but how to you read the s-meter on a TMD700? Generally, a S-meter will have 9 levels. My Kenwood TH-F6 has 9 bars. But on my TM-D700 it only has 7 b
|
By
Brad (KE7HFP)
·
|
|
D700 Cooling fan always runs 6 messages
The fan on my d700 always turns on the moment I key up. Is this normal, a setting change, or is it "malfunctioning"? It's a bit annoying as the fan is noisy. Wondering if anyone else has experienced t
The fan on my d700 always turns on the moment I key up. Is this normal, a setting change, or is it "malfunctioning"? It's a bit annoying as the fan is noisy. Wondering if anyone else has experienced t
|
By
wa6drd@...
·
|
|
TM-D710GA extended manuals ... 2 messages
Hi all, Does anyone know where I can download the D710GA extended manuals? Kind regards, Richard Main VK3BP
Hi all, Does anyone know where I can download the D710GA extended manuals? Kind regards, Richard Main VK3BP
|
By
Richard Main
·
|
|
How to set Packet96? 3 messages
What are the steps to enable Packet96 on TM-D710GA? I can only enable Packet12. When I hit the TNC key I get Packet12, APRS96, or bank. xastir receives and transmits with Packet12 @ 1200 baud but look
What are the steps to enable Packet96 on TM-D710GA? I can only enable Packet12. When I hit the TNC key I get Packet12, APRS96, or bank. xastir receives and transmits with Packet12 @ 1200 baud but look
|
By
Paul Sundquist-WF7U
·
|
|
Backspace 7 messages
While using Screen through Terminal on my Mac to connect to my TM-D710G, I haven't found a way to delete mistakes without using CTRL-X, which removes the entire entry without transmitting. The TNC2 ha
While using Screen through Terminal on my Mac to connect to my TM-D710G, I haven't found a way to delete mistakes without using CTRL-X, which removes the entire entry without transmitting. The TNC2 ha
|
By
Joshua KJ7LVZ
·
|
|
Looking to buy 11 messages
I tried an FTM-400 and didn't love it so I sold it and got a 710G. The other truck has had a TM-V71A since I got my license but I purchased another FTM-400 thinking I'd give it another shot. Well, it
I tried an FTM-400 and didn't love it so I sold it and got a 710G. The other truck has had a TM-V71A since I got my license but I purchased another FTM-400 thinking I'd give it another shot. Well, it
|
By
Joshua KJ7LVZ
·
|