Pat, Thanks for spreading the word. I have had positive comments on my guide. Scott, K7AID did a good job hosting the information on his site: http://www.hamhowto.org/index.php?title=APRS_-_Primer I f

I have an Kenwood TM D700A, and I would like to start to use the APRS functions of my radio. I would like to see if any one has any suggestions for a GPS I need to get. I am starting from scratch on t

Hello Mike, your path should really be changed, while it will work, it's far better to follow the new path scheme. You'll see this now on aprs.fi: http://aprs.fi/info/a/KD8ZCM Last path: KD8ZCM>EB5V0R

and around a million or so miles bouncing around in an over the road truck, my D700 started acting weird. It would lock up, as if it could not process packets. Turning it on and off seemed to resolve

Hi All, I have an Arduino set up with a TNC for APRS position reporting and messaging. I am getting messages that look like this: KK6NQK-11>APRS,Wide2-1:@2400.00N/12100.00EO1/F=NO00/A=0.0 I am trying

I am trying to program 159.2025, but it will not let me. Any advice? ----- Original Message ----- From: Elwyn yahoo-groups@... [TMD700A] To: TMD700A@... Sent: Friday, September 26, 2014 7:31 AM Subjec

You are certainty welcome here, but there is a TM-D710A Yahoo reflector at: https://groups.yahoo.com/neo/groups/TMD710A/info 73 from Bill WD8ARZ

I'm sorting out a memory file for my D710 and I've got an odd thing. So. I've exported to a HMK from the data from the radio software and editing it as a CSV, as per online instructions. However, for

I have 2 TMD700 I would like to sell. one looks near new, never been mobile. $600obo for both, $350 each, shipped in cont US

Hi, I'm having a hard time reading the front panel on my D700. At night it is fine but during the day in bright sunlight it is almost impossible to read the frequencies on it. I have it mounted low on

I just started using my Kenwood TM-700 again with the MC-53DM mic and I have gotten a few signal reports that said that the radio had "low Audio". I've seen a few posts on the subject. Does anyone hav

The other night I was talking on my 700a when everything went dead. The face looked like I was still transmitting even though the handheld said otherwise. I shut the radio down and tried it again. Thi

Good morning Larry, Few things to verify. - Make sure the power supply is supplying the right voltage, and can support about 15 amps current. - Test into a dummy load in case the coax or antenna have

Group: My TM-D700A is putting out only 25 watts (+-) on 2 meters and 15 watts (+-) on UHF. It is set to "H"(igh) power setting. If the rig has two power output transistors in the PA section, I suspect

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the TMD700A group. File : /K9DCI's Excel CAT & Beginner Guide & Mic quick guide/APRS Begi

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the TMD700A group. File : /K9DCI's Excel CAT & Beginner Guide & Mic quick guide/APRS Begi

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the TMD700A group. File : /K9DCI's Excel CAT & Beginner Guide & Mic quick guide/D700 OPEN

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the TMD700A group. File : /D700 OPENING TNC Fixes Rev-6.pdf Uploaded by : noskosteve <nos

Hi all, Have a problem with a TMC700 Here, it just sits at "Opening tnc" when you try and turn the TNC on. I have tried a reset but it still doesnt work. any thoughts? 73 Matt

Hi folks- at the recommendation of several of you on here, I ended up sending my rig into AVVID repair (Clif Holland KA5IPF) and he was able to get things diagnosed and repaired. Thank you for the sug