I don't normally forward commercial emails, but I've bought from this company before and they just released a new seat bolt mount for the Kenwood D710 & V71 radio control head. I figured it was releva

I’m looking for advice concerning a choice between my old D700 and a new D710. I'm getting a new car and plan to install one of these 2 radios in it. The D700 still works fine, so I could use it. But

I have a TM-D710A in a fixed station. I hadn't exercised the APRS in a while and decided to transmit a few packets. I hit BCON and no TX. I'm not using a GPS and have it set to use a single location.

I'm looking at jumping several generations ahead in technology and replacing my old faithful Yaseu FT7900 dual-band FM transceiver with the TMD710A. I assume the 710A has the capability of storing mem

I use my TM-D710G for numerous purposes, including APRS & Winlink. At present, I have different configuration files saved in the MCP-6A memory control program directory and download those to my radio

You may need to navigate to the group website to remove yourself. You may have signed-up with a password that is required to "unsubscribe" you. Unless an administrator of the list sees your message, s

Hello, My son dropped his TM-D710 control head and broke off one of the right-hand knobs. I am looking for the part number and source for the knob module. (Also replacement knobs...) Thanks in advance

Hi While I was servicing my venerable D700A, I inadvertently broke the ribbon cable connector on the main rxtx board which connects to the tnc board, I checked with pacparts.com and they do stock the

My 18 month old Kenwood TM-D710GA radio "decided" this past week that it didn't want to work in APRS12 TNC or PACKET TNC anymore. I had never gotten around to using this radio in digital modes until I

Anyone know of software to control the TM-D710G? Thank you 73 Emory WM3M

I am pretty much certain that I have carefully read the Scan section of the D710 PDF. When I try to scan, all I get is scan through whatever frequency I am on. ....118.5 (from a lower-limit) . I will

Correction to my last reply. I listed the wrong GPS. It is the unit with the serial cable. Garmin 18x PC GPS Navigator Unit https://www.amazon.com/Garmin-18x-GPS-Navigator-Unit/dp/B0016NYHVS/ref=sr_1_

So Finally transferring my D710 to my new truck, and I am looking for a better solution for the GPS unit. Currently I have a hacked together Magnetic GPS unit that I threw together with a small breadb

FOR SALE: TM-D700A I've been using this mobile in my truck for several years. Works perfectly. I want to go with a digital mobile so I want to sell the KenWood. I have found the original Box! Still lo

My D710 appears locked. The panel shows it's locked and all the panel and mike buttons and knobs beep when pressed or turned. This implies two things; it's locked and all the buttons (including knob p

Hi all, fairly new to VHF, etc, but fairly competent with technology. Try as i might, I cannot get my SSID of -9 to stick when programming my SSID. I have tried VA7RKC-9,as well VA7RKC9 to no avail. t

Hi In a previous recent post I have indicated that my radio is refusing to start evidently because it cannot recognize the tnc because of the broken ribbon cable connector. When I try to start, the ra

Hi I am willing to purchase a dead D700A to use as parts. I am in need of a discontinued connector. Please reply offline to joe at laferla dot ca. Thanks. Joe VA3JLF Sent from Mail for Windows 10

When I look on Findu, I see I haven't sent a GPS position in over a day. Yet I think I beacon several times an hour from the fixed location. I do have my precise position in the #605 memory position o

Trying to setup d710ga with fldigi. I am using the pg5h (I think that is the number) cable from kenwood was plugged into the rs232 of my computer and into the back of the radio not the back of the det