Anyone have one for sale, reasonably priced and good condition? Alternatively, is there a replacement PC board? Looks like most items are plug & play on it. Saw a site called PacParts which looks like

Entire station forsale Icom IC-7800 ... $3,800 IC-756 Pro III .... $1,200, Kenwood TS 990 ... $4,300 Elecraft K3 w/ P-3 ..... $2,350 Flex 6300 ...... $1,550 Yaesu FTdx 5000 .... $2,500 Icom PW1: ....

My TH-D700A is now on its 4th install location. It's been in 3 different vehicles and now has been retired to shack duty. It has developed an issue with the PTT. When I key the mic, sometimes it trans

I just cleaned off the dust of a D700A that's been sitting in our Search and Rescue team trailer for years. The individual who programmed it left the team long before I joined. Using the programming s

Eric, you can check for firmware / software versions / updates at Kenwoods web site: http://www.kenwood.com/i/products/info/amateur/software_download.html No updates are listed for this radio. But it

Does anyone know of or have a UHF Module M57788MR or a cross part number for the module any other suggestions to get the UHF side back working it is txing just no power out have full drive level to mo

FLex 6300 Flex 6500 Icom IC 7850 Icom IC 7600 Elecraft kx3 Elecraft K3/P3 Pls contact me with your offers. Prices are very competitive. 73 K9FS k9fs73@... Dr. Bob Kieffer ,.

Here is my thinking on a ham radio station and other equipment on battery operation. The battery system must have the capability to be operational 24 / 7 - Therefore I dont rely on just commercial pow

I have a 2014 GMC Sierra SLT with a center console. Looking for any advice on install of a D710. Looks like there is room under the front of the console with access via the side panel. Thanks, Joe, KC

anyone ever had problems with Avmap 6 displaying stations? I followed everything the way it should be and my radio is following flashing the GPS icon on the radio so I know it's talking to GPS, the TM

Price: Flexradio 6500: $2,750 Flexradio 6300: $1,700 Elecraft K3/P3: $2,200 Elecraft KX3: $1,000 Icom IC Pro3 756: $1,155 Icom IC 7600: $1,800 I am downsizing my shack. Mike Carron Email: kb1sdw@... M

Just a quick question. I intend to have the radio in the trunk of my care solely for APRS tied in to a PI. Question is, can the radio operate without the faceplate? I know i can turn it on and off via

All The clip on the RJ45 jack on my microphone snapped off. I attempted to replace to RJ45 twice but when I plug the mic in to the radio it goes in to transmit mode. I matched the pin outs carefully a

I am moving into a smaller apartment, so these rigs have to go. Icom IC pro 756 III : $1,250 Icom IC 7800 : $5,000 Flex 6300 : $1,900 Acom 1000 : $1,500 Elecraft k3/p3: $2,200 Elecraft KX3: $1,050 Yae

I was playing around with APRS tonight and did get it to send APRS packets in the PTT mode. They showed up fine on APRS.FI. However, I was not able to get any automatic beaconing to work correctly. I

I am looking to take my Kenwood TM-D700A and connect to my PC possibly? I spoke with John at coastal chip and the old TNC to keyboard interface that they made is not made no more. I want to have my D7

Hi, I'm looking for the layout for the remote control cable between the control head and the radio. I know on the control head there is a 4 pin connector, but on the radio side is a 6 pin connector. I

Hi, My TM-D700A(G) went dead today, can't turn it on. Failed while driving. My question is, I looked in the file section and I hope found my problem, at least I'm hoping. I will make me a cable to ver

Is anyone using a MobilinkD device on their machines?

Here is an interesting issue with a TM-D710 mobile user who has an APRS message that he tried to send, but this or a partial message has repeated >1000 times. Tried to send an APRS one-line to this mo