Ladies and Gents, I would like to extend my use of Winlink from strictly HF/Winmor using an FT-857 to VHF using the D710G's built-in TNC. Would anyone like to point me to a configuration table, drawin

As a new member and a new comer to the D710G, I have a question re. how to save an APRS configuration to PM. My default configuration is created for a "fixed" location. However, I would like to also s

Hi All, Has anyone changed the fan in their TM-D700? Will a standard 40x40x10 work or is there anything special about the Kenwood fan? Thank you!!! 73! -Dave

Hello to the group, I need help on programming my radio for a repeater so that it has a DCS tone only transmitting and no DCS code on receive. 145.470 -600 with a DCS tone of N047 on transmission only

One Important question please,,,, This is my first Kenwood experience. I replaced my Yaesu 8900 duel band in my 2016 Dodge Ram. Heres my issue, every time I transmit on 147.285 it breaks squelch or in

Merry Christmas and Holiday Greeting everyone. I have recently gotten back to APRS with my D710 and no longer have individual position reports showing on the screen after the arrival of a packet, like

http://houstonknanayacatholics.com/rnwbton.php _but in this world nothing can _be said to _be certain, except death and taxes. Deemer Sinks

Has anyone figured out the protocol between the radio and the head? My idea was to use a D700 body and plug in a custom interface that I could emulate the control head. I am aware I can control the ra

Hello Ray, great to hear fro you. Great info on your battery system and what you have using it. Must feel good for your gear to be ready to be used regardless of commercial power status. Of late have

Sometimes I use my mobile TM-D700 mobile radio for a base station too. Like in the mobile, I have set it up on its own battery operation system. Hopefully will hear about your power sources too ....ï¿

I currently have a 700 that is going to move to the shack for the remainder of it's life so that means a new mobile unit for me and I am looking at the 710 having loved the 700 so much. Now here is th

When an external GPS sensor was needed for a computer program, or ham radio externally connected to a radio such as the Kenwood TH-D7AG Walkie Talkie, I have used two types: BU-353S4 Round with magnet

Here is how I do SkyCommand and APRS from my Mobile & Handy Talkie. It sounds more difficult than it actually is. Install and configure one portion of the system at a time. Test it, and debug as neede

Years ago I purchased a Garmin GPSMAP 276C, which is the GPS I'm still using with my TM-D700 today. Some of you may have also bought this same model. I also use it in the marine mode when we go on vac

Here are some links that should get you to the interface cables needed to access the radio and configure / operate Skycommand mode. There are of course others who sell the same cables, so you can shop

Good evening all, I was wondering if anyone has had any luck with using the BU-353 GPS unit with a D700? The BU-353 is a USB GPS, but I'm happy to chop the end off and re-wire it. I did read somewhere

Well, should it work? I use RT's software and cable to program the memory in my 710. Works fine. I wanted to get my feet wet with Winlink, so I loaded up the software, moved the RT cable to the COM po

Reading through this newsgroup it sounds like the battery may have gone kaput on the main board causing the radio to reset itself every few times I turn it on. Any advice on replacement batteries? Sen

My 14 years old TM-D700 is now has a flaky encoder button, sometimes it jumps the opposite direction when I turn (jumps up when I turn the frequency down, or jumps down then I turn the freq up), very

Hi, I have a 710 at home and another in my truck. I can use a TH-D72A to control either in remote mode. I can cause them to go into or out of cross band repeat mode, etc with commands from the D72. My