Hope this is permitted. I live in the Dallas / Fort Worth Area. Any help would be appreciated. Ok, still having problems. GPS is a Garmin 3+. GPS interface set to NEMA 4800. Radio Kenwood TM-D700. TNC

While using APRSIS32 with my D710GA, I was noticing I wasn't seeing any APRS decodes coming out of the 710. I had CH1 on 144.390. I had CH2 on 145.825 and that CH output being read by AGWPE/UISS .. I

Is there a way of overriding APRS beacon lat/lon coordinates with specified, rather than dynamic ones from internal GPS? Alternatively, is there a way of disabling internal GPS altogether? Thanks Leo

Has anyone heard any rumors about Kenwood adding FX.25 support (https://en.wikipedia.org/wiki/FX.25_Forward_Error_Correction) to the firmware for the D700/710? The next release of Direwolf (V1.6) incl

I just acquired a D710G. I'm using an external GPS since the internal is not great at getting a GPS signal indoors. I set up for the external GPS and I know it's getting position information. The GPS

I'm looking at installing the D710 in my Jeep as my mobile setup. I know 12V is standard... It looks like it comes with a set up to connect directly to the battery. My concearn is that the volts on my

I noticed that on Findu that my last Lat/Lon update was 2 days ago. And yet I have beaconing to every 20 minutes. What's the key to setting the rig to do that? thanks -- -- Bob KD7YZ TM-D7100GA

Strangest thing. This morning whenever I digipeated or Tx'd , I heard the Beep. Came back after a 30 mile run to get groceries and noticed there are no more beeps when I KNOW it is supposed to be doin

My old Garmin GPS-35 finally died. It has been connected to my D-700 for over 15 years in my truck. My question is What is the current best deal on a No Display GPS that will work with the D-700 ? The

GM Subject pretty well states my question. Somewhere in the setup I may have missed the answer. However, it is not obvious to me. At the moment, I am scanning a handful of both 2m as well as 440 repea

I have a new TMD710GA and I'm not able to receive my APRS messages to be read. I can send them. Ed / K8EAF

Anyone know the part number for the final transistors! Also any idea of other things that cause no transmit? Maybe a service center? Thanks in advance Ron K1VSC

Hello all, I looking for a servicedoc for a Kenwood TMD710GE/A , i looked at mods.dk but only the servicedoc for the TMD710E/A is there , not the G version. Can someone help me with that ? I have some

Hey guys, I am a new owner of the TM-710G. I purchased a USB 8 pin cable for the programming but I am not sure which cable to use for DATA. I am assuming that I need the DATA cable to access the TNC f

D710 will not transmit Winlink Express Packet messages to an active RMS station 3 miles away. When I open a message session in Winlink and press "Start", the radio goes completely silent. No audio hea

Just received my 710G which I am going to replace a Yaesu FT400XDR which I found to have lots of poor human factors in the areas of updating firmware and programming in general. I have 2 questions abo

I am hoping someone can provide some insight I am having with my TM-D710GA. When the radio is powered on, the iGPS indicator will come on for two or three seconds, the turn off. I can press the functi

Hello all, I have a odd problem with my TMD710GE with the latest firmware. When i am on memorychannels on both vfo's,only VFO B is not going in reverse when the channel is programmed in repeater. VFO

Hello, I have an older d-710a that I recently acquired. I am having trouble figuring out the group scan/ group link features. The manuals are less helpful than I need. Anyone have experience with thes

set Ch B to that QRG and 9600b but was running through AGWPE and figured that was wrong protocol. Or I set the Rig up incorrectly. I can ask over on AMSAT but thought there may be another D710 using f