I was listening to a repeater on my D700, walked out of the room and came back and it was off. I tried turning it back on and the screen flashed some black momentarily but nothing else happened. No ba

I have Kenwood TM-910A radio SN906xxxxx with Panel firmware v2.13 This older firmware was working fine. Had all Aux 900 menu items ie 923 REMOTE ID Today decided to update. Went on Kenwood website and

Does anyone have a setup guide for the Kenwood D710 for WInlink using the DRA 50 board and VARA?

Lately my D700 has started powering itself off. Radio is in shack, powered by good PS. I hear the speaker pop as if the power button has been touched and the radio powers itself down. Yesterday heard

Hi I have just obtained a D710GA and am trying to use the internal tnc to do aprs. Can someone help me with how to connect the radio to the computer which runs my aprs software? I have the kenwood pro

I've owned my TM-D700A for probably fifteen years now, but have never needed to change the default step size ... until now. The manual says: 1 Press the left or right [BAND SEL] to select band A or B.

For quite a while now, I have left my TM-D700 listening to APRS, and not transmitting. Here recently, it will randomly transmit. What may be doing this? Tnx & 73, Kim - WG8S

As any owner of this radio learned after about a minute of using it, the control microphone with which the package comes is not a stellar performer. It has its own distinctive sound, and since I'm usi

I'd like to use a SignaLink with my TM-D710G rather than the TNC. Other than turning off the TNC and cabling the SignaLink to the DATA jack, are there other settings on the radio to configure differen

I have been experiencing a continuing problem with aprs that I do not seem to be getting out enough, even with full 50w power. I am using the D700A in tnc pkt mode. I am only able to get digipeated by

I am trying to use my d700a with yaac or another aprs program to receive and transmit aprs packets. Everything is set correctly and I can receive packets correctly. However I cannot transmit. The soft

I am trying to connect my tmd700a with my aprs client yaac and am getting an error message that the com port cannot open. I have a straight through rs232 cable connecting the radio to the computer as

Have had a Yaesu FTM-350AR for years and decided to come back to Kenwood. Now I have the Kenwood TM-D710G and the radio seems to be great except for the display. Have not found a way to make the Memor

Ok. I’m sure it’s easy but I can’t figure out how to put the TM-D700 into 9600 baud packet. No issues with APRS 9600, not able to access 9600 packet. Any help appreciated. Set 9600 in the software pro

I own three D700 radios and bought them new many years ago. I recently ran into a problem with one of them when I could no longer turn it on via the power button. At first the display would turn on wi

My D-700 Mobile SatGate quit forwarding the ISS DIGI to the Terrestrial network. I see everything from the ISS but my radio forwards nothing. I went through all my settings and I can't see any error.

I don't normally forward commercial emails, but I've bought from this company before and they just released a new seat bolt mount for the Kenwood D710 & V71 radio control head. I figured it was releva

I’m looking for advice concerning a choice between my old D700 and a new D710. I'm getting a new car and plan to install one of these 2 radios in it. The D700 still works fine, so I could use it. But

I have a TM-D710A in a fixed station. I hadn't exercised the APRS in a while and decided to transmit a few packets. I hit BCON and no TX. I'm not using a GPS and have it set to use a single location.

I'm looking at jumping several generations ahead in technology and replacing my old faithful Yaseu FT7900 dual-band FM transceiver with the TMD710A. I assume the 710A has the capability of storing mem