I have had a lot of success with my Kenwood D74 working the ISS on APRS with the TNC on VFOB and recently got a D710 for my car. Being that the radio is in the middle of my car and I sit on the left,

Greetings, I recently set up a new dual band (VHF & UHF) Winlink RMS Packet gateway. The UHF band uses a Kenwood D700 radio that is set to operate at 9600 baud. A nice feature of this radio is that it

One side (left) display shows busy with no s-meter reading, squelch control has no effect on "white" noise, signal incoming works ok, tone setting works ok,, B side squelch works and receive properly.

Hello, I own a TM-D700 for long time. I always keep the unit switched on. Switch off will be taken place by power supply. When I switch PS back on, in the past the TM-D700 came up again. Now, suddenly

Another group I'm a member of (AT - Golden Packet), which has used the Kenwood TM-7XX line of radios to send APRS messages up and down the Appalachian Trail during an annual July event, has had severa

Has anyone reversed the out of band mod? This is the mod that requires removal of a SM resistor and cutting or unsoldering one end of a green jumper wire. Bob, N7GTE

I need the basic instruction manual for the TM-710GA which is on the DVD and a paper copy in the radio box. It must be legal (copyright - wise). I would like to email page numbers for question and ans

For Sale: Working Tested radios tested with a working control head. Can be operated with CAT control cable (not supplied) and software. 2 available: Kenwood TM-D700 Radio body (NO CONTROL HEAD) with m

Anyone have an idea how to get the saved track logs and marked waypoints off a D710G? I have and RT cable that I use for the TNC and programming. Also, I use a Macbook. If there is a Linux software op

my garmin II plus shows three or more sats but no lat long shows, any ideas... joe

Hello, I have a kenwood tm-v700, one afternoon, I turned it off working perfectly, but in the morning of the next day, I could not turn it on, after several attempts, it worked with the following mess

A few weeks ago I replaced the 4 filters in my TM-D710A and all worked just fine until the other day. Now, when I turn on the radio I get the usual 2 beeps then another beep, which I had never heard b

I just got a Kenwood D710a that had firmware 2.10 installed, figured I would go ahead and update it since the MCP software was complaining. Firmware updated fine, did a full reset, but when i try to u

I often hike with a KWD TH-D74a running APRS SmartBeaconing. Where there is no/little digipeater coverge, I’d like to park my car at the trailhead and use my KWD TM-D710G to pick up my 5W TH-D74a beac

I am a couple decades behind for packet radio (apart from APRS) but I'm having fun anyway. I have a TM-D710G and I connect to its TNC through my Macbook and an RT Systems serial to USB converter. It's

Hi: I am looking for a D-700A Control Head or the complete radio. Must be Firmware G2.0 revision and a 41 Million + Serial Number. Tnx 73 De Mike VE3YF

I had the need to reset my radio the other day because I got it into some state where I could not set any band to transmit or receive. I went to menu 1-9-7 and did the full reset. I then went to 1-2-4

Hi, I have manage to successfully change the ceramic filters on my TM-D710E, but I knocked off C509 in the process. It's way too tiny for my soldering skills and tools so, I was wondering if anyone ca

I keep the stock microphone connected because it has the DTMF keypad which, of course, doubles as a miniature control device. However, as we all know, it's not the greatest microphone on earth. I'm lo

Hello everyone. I am an Italian ham IW1GK . I have a problem with my TM-D700 G2. Unfortunately it stopped working and I found the cause in the display . I am 99% sure that the defect lies in the displ