What are the steps to enable Packet96 on TM-D710GA? I can only enable Packet12. When I hit the TNC key I get Packet12, APRS96, or bank. xastir receives and transmits with Packet12 @ 1200 baud but look

While using Screen through Terminal on my Mac to connect to my TM-D710G, I haven't found a way to delete mistakes without using CTRL-X, which removes the entire entry without transmitting. The TNC2 ha

I tried an FTM-400 and didn't love it so I sold it and got a 710G. The other truck has had a TM-V71A since I got my license but I purchased another FTM-400 thinking I'd give it another shot. Well, it

Includes: TM-D700A Scanner Serial Cable GPS Cable Bracket for head and radio Remote Head cables. Price $175.00 include shipping CONUS

Okay, you packet junkies, I have a question about the internal TNC. It have an MFJ-1270B that I am using to connect to my 710G. On the 710G I have CONOK ON and BBS ON. I can connect to my 710G but the

Has anyone run APRS using a Bionics GSP2 receiver with a TM-D710A mobile? I emailed Bionics to ask if this combination would work, but never got a reply. Thanks - ed, k9ew

I, and others for me, solved the WxNow and Weather data issue. So now I was trying to figure out how strong or IF the D710G is receiving any GPS Sats. I "Think" I have the window open. Its got a Compa

I note several stations on my APRSIS32 display who also have a blue Wx symbol. How to I get the info from the Davis VP2 Console to the Davis-APRS-Wx jack a 2.5mm 3-pin plug ??? My Davis already has an

I have a 700 and am using the internal TNC as a fill in digipeater for APRS. I've set the Lat and Long and settings that I think should allow it to display proper location, but it puts the radio at La

Hello TM-D710GA List I need some serious GPS data help. In the last couple weeks I have, rather apparently, QSY'd to beautiful outdoors Ontario Canada! While I have actually ice-skated to a work assig

The front panel LCD is cracked. Front panel works, but the display is boogered beyond repair. I am looking for a DOA front panel or complete dead rig or just the LCD. I really don't want to buy a comp

Hi group... I am trying a TM-D700 with a Signal Link through the 6pin Data port. The internal TNC is off. I cannot get connection to any local winlink packet sites with this configuration, or with the

I have had a lot of success with my Kenwood D74 working the ISS on APRS with the TNC on VFOB and recently got a D710 for my car. Being that the radio is in the middle of my car and I sit on the left,

Greetings, I recently set up a new dual band (VHF & UHF) Winlink RMS Packet gateway. The UHF band uses a Kenwood D700 radio that is set to operate at 9600 baud. A nice feature of this radio is that it

One side (left) display shows busy with no s-meter reading, squelch control has no effect on "white" noise, signal incoming works ok, tone setting works ok,, B side squelch works and receive properly.

Hello, I own a TM-D700 for long time. I always keep the unit switched on. Switch off will be taken place by power supply. When I switch PS back on, in the past the TM-D700 came up again. Now, suddenly

Another group I'm a member of (AT - Golden Packet), which has used the Kenwood TM-7XX line of radios to send APRS messages up and down the Appalachian Trail during an annual July event, has had severa

Has anyone reversed the out of band mod? This is the mod that requires removal of a SM resistor and cutting or unsoldering one end of a green jumper wire. Bob, N7GTE

I need the basic instruction manual for the TM-710GA which is on the DVD and a paper copy in the radio box. It must be legal (copyright - wise). I would like to email page numbers for question and ans

For Sale: Working Tested radios tested with a working control head. Can be operated with CAT control cable (not supplied) and software. 2 available: Kenwood TM-D700 Radio body (NO CONTROL HEAD) with m