I got this radio as a broken, panelless radio. Got a tm-d700 panel, I can do each and every function, radio has tx and rx. But no speaker audio whatsoever. No beep from keypresses and no squelch actio

Yes, it is possible. It is not cost-efficient, it is not reasonable, but it is possible indeed. I will write a complete and detailed article about that in my blog. But basically, all TM-*70* radios ar

Anyone who is running an Echolink Repeater Node on a TM-D710A who has any info to share on getting it set-up, and operating "Tips & Tricks," I would appreciate hearing from you. The goal is to set up

Quick question... I'm changing the setup of my TM-D710GA, which will basically have the head unit sitting right on top of the main body, on my desk. I don't need the millions of feet of 'ethernet' cab

Hello, I am using a TM-D710G located in my barn. I'm using a TH-D72 handheld from my house. I want to use it for different functions. Function one, Cross-Band repeat Function two, External data for an

Greetings All! Just got a TM-V708A Body which seller says it is working OK, but no head. He said it was tested with a TM-D700A head. I got a TM-D700A head, built the cable and the set mostly works. I

Recently my screen has been blank upon startup and slowly reappearing to pre-set brightness and contrast after 20 or so minutes. Functionality of the radio seems fine. Settings and environmental condi

Ok I have both a TM-D710A and a TM-D710GA. The unit will not power on if the TM-D710GA head is attached to a TM-D710A transceiver body. It looks like the TM-D710GA will not work with the TM-D710A tran

I have a D700 I've been using for at least 10 years. It has always worked perfectly for all my needs including APRS which has been running for most of that 10 years. On July 19th I left Kansas City fo

The big knob on the left of my TM-D700 is slowly get erratic (readout jumps back and forth whenever I rotate the knob), and lately sometimes I don't feel the clicking feedback. Anybody has the source

I am considering using my D700 as a VHF Winlink Node with Vara VHF. Is anybody else doing this? I have been using it for APRS but I’m in an area where a Winlink Node for VHF/UHF would be more useful f

I have a TM-D710A which I am using for APRS. I am testing it at 9600 baud. Using my deviation meter, it looks like it is over deviating and it can not be decoded by a D710GA, D72A, or a component base

I have a D710A. We were using it in a public event. After about 9 hours of net control use, transmit failed. We attributed it to a high SWR in the antenna and replaced the transceiver unit. We were us

Most of my radios require I take action for it to connect to the computer. I find no instructions in the two D700 manuals on that. When I plug in the serial port, the radio and computer do not communi

Has anyone figured out how to reset the power on password in the D710G? Here's what happened. I wrote my config to the radio with the password button checked in MCP-6A software. Now I realize the pass

Hello everyone. I have been out of ham radio for many years, and when I stepped back in a fellow ham gave me a TM-710A that he said was a spare. It still had the film that covered the screen, and the

Hello. It was suggested that I need to do a hard reset of the radio. In the owner's manual, page 33, it has menu 999, but will this do a hard reset of the whole radio? Under "setting values" there is

Greetings D700 enthusiasts (and hopefully an expert or two), Having read the D700 manual and the Specialized Communications manual, I cannot tell what sets the band used when a Mini-DIN-connected devi

My D700 has developed a problem. When I turned it on today the message on the control head read the following PROG 115200 bps, Trying various buttons etc made no difference. Anyone had this problem or

Hey everyone. I'm new to this forum. I've had my Kenwood TM-D710GA for a few months. It basically functions as my base station, but I like to play with APRS...and especially the messaging. I've had it