Fw: [VWS] TM-D700 Questions


hardlyevrhom
 

I would check the AIP setting, menu item 1-3-5, if it is on it would
explain the problem. The AIP is great for limiting the intermod
monsters in a metro area, but really kills the receive sensitivity.

Kurt
KC8RWD-14
--- In TMD700A@..., "Daniel J. Sullivan" <djs13@...>
wrote:

Any thoughts on this folks?

Dan S
KO1D
----- Original Message -----
From: "Craig"
To:
Sent: Friday, February 17, 2006 8:17 PM
Subject: RE: [VWS] TM-D700 Questions


At 05:56 2/17/2006, you wrote:
Not sure on this one Corky. I have never had this issue. You may
want to try and send this out on the D700 Reflector on Yahoo
(or I
can for you if you like) for a wider bit of feedback.

Dan S

----Original Message Follows----
From:
Reply-To:
To:
Subject: [VWS] TM-D700 Questions
Date: Thu, 16 Feb 2006 20:43:11 -0700

For all of you out there with a D700, mine is showing rather
bizarre
behavior and I was wondering if anyone else had experienced
this or
might have some suggestions as to what I might do about
it. Basically the problem comes down to the unit being
essentially
deaf. That is the front end sensitivity, as determined by
terribly
unscientific testing, appears to be about 1/4 or worse than
that of
my TH-F6 with a rubber duck! So here is the test and the
results.

The unit is mounted in my car with a Diamond SG9600 tri-band
antenna
(6m-2m-0.7m). I am running APRS (144.390) on channel A and
attempting to access a repeater on channel B (147.060). I was
at a
point where I could see the mountain on which the repeater was
located even though it was some 50 mi. away. I was unable to
get
the repeater to even break the squelch (or hear the repeater
with
the squelch open) on the D700 running at high power.
I thought, this seems strange so I pulled out the Th-F6 with the
rubber duck and keyed it up from within the car and brought up
the
repeater and could hear the repeater at full quieting without
any
problem. The squelch still did not break on the D700 so I
opened up
the squelch all the way and could not hear either myself
transmitting with the HT or other people operating on the
repeater
that I could hear with the HT. Next I transmitted with the D700
and, listening with the HT found that indeed I was keying the
repeater, just not hearing it. With a power meter I verified
the
VSWR to be about 1.1 or less and the transmission was about 50
watts
into the antenna. Next I put the HT on the external antenna
that
had been on the D700 on the HT and the signal in and out only
got
better. To make matters worse as I approached the repeater
site and
cut the line of sight distance by about a factor of three to
four
(1/4 to 1/3 the distance at which the HT was at full quieting)
the
D700 woke up and heard the repeater signal. I am running a tone
(67.0 Hz) and no CTCSS. The S-Meter squelch is off so the
squelch
should behave normally. This same sensitivity problem seems to
exist on channel A that I was using for APRS, thigh I did not
notice
much because I kept the volume off on that channel until I
started
having problems. Since I did not have a means to decode the
APRS
signals on the HT I could not verify that I was getting full
signals, but the HT was hearing many more broadcasts on 144.390
that the
D700.

As I said, if anyone has a some suggestions as to things to try
or
check before I box it and mail it back to Kenwood it would be
greatly appreciated.

Thanks,
-Corky
AF4PM

So that is the story


--------------------
For information on subscribing or unsubscribing to this or our
other
mailing lists, please see the Vienna Wireless Society web site:
http://www.viennawireless.org/lists.php



--------------------
For information on subscribing or unsubscribing to this or our
other
mailing lists, please see the Vienna Wireless Society web site:
http://www.viennawireless.org/lists.php


--------------------
For information on subscribing or unsubscribing to this or our
other
mailing lists, please see the Vienna Wireless Society web site:
http://www.viennawireless.org/lists.php


Daniel J. Sullivan <djs13@...>
 

Any thoughts on this folks?

Dan S
KO1D

----- Original Message -----
From: "Craig"
To:
Sent: Friday, February 17, 2006 8:17 PM
Subject: RE: [VWS] TM-D700 Questions


At 05:56 2/17/2006, you wrote:
Not sure on this one Corky. I have never had this issue. You may
want to try and send this out on the D700 Reflector on Yahoo (or I
can for you if you like) for a wider bit of feedback.

Dan S

----Original Message Follows----
From:
Reply-To:
To:
Subject: [VWS] TM-D700 Questions
Date: Thu, 16 Feb 2006 20:43:11 -0700

For all of you out there with a D700, mine is showing rather bizarre
behavior and I was wondering if anyone else had experienced this or
might have some suggestions as to what I might do about
it. Basically the problem comes down to the unit being essentially
deaf. That is the front end sensitivity, as determined by terribly
unscientific testing, appears to be about 1/4 or worse than that of
my TH-F6 with a rubber duck! So here is the test and the results.

The unit is mounted in my car with a Diamond SG9600 tri-band antenna
(6m-2m-0.7m). I am running APRS (144.390) on channel A and
attempting to access a repeater on channel B (147.060). I was at a
point where I could see the mountain on which the repeater was
located even though it was some 50 mi. away. I was unable to get
the repeater to even break the squelch (or hear the repeater with
the squelch open) on the D700 running at high power.
I thought, this seems strange so I pulled out the Th-F6 with the
rubber duck and keyed it up from within the car and brought up the
repeater and could hear the repeater at full quieting without any
problem. The squelch still did not break on the D700 so I opened up
the squelch all the way and could not hear either myself
transmitting with the HT or other people operating on the repeater
that I could hear with the HT. Next I transmitted with the D700
and, listening with the HT found that indeed I was keying the
repeater, just not hearing it. With a power meter I verified the
VSWR to be about 1.1 or less and the transmission was about 50 watts
into the antenna. Next I put the HT on the external antenna that
had been on the D700 on the HT and the signal in and out only got
better. To make matters worse as I approached the repeater site and
cut the line of sight distance by about a factor of three to four
(1/4 to 1/3 the distance at which the HT was at full quieting) the
D700 woke up and heard the repeater signal. I am running a tone
(67.0 Hz) and no CTCSS. The S-Meter squelch is off so the squelch
should behave normally. This same sensitivity problem seems to
exist on channel A that I was using for APRS, thigh I did not notice
much because I kept the volume off on that channel until I started
having problems. Since I did not have a means to decode the APRS
signals on the HT I could not verify that I was getting full
signals, but the HT was hearing many more broadcasts on 144.390 that the
D700.

As I said, if anyone has a some suggestions as to things to try or
check before I box it and mail it back to Kenwood it would be
greatly appreciated.

Thanks,
-Corky
AF4PM

So that is the story


--------------------
For information on subscribing or unsubscribing to this or our other
mailing lists, please see the Vienna Wireless Society web site:
http://www.viennawireless.org/lists.php



--------------------
For information on subscribing or unsubscribing to this or our other
mailing lists, please see the Vienna Wireless Society web site:
http://www.viennawireless.org/lists.php


--------------------
For information on subscribing or unsubscribing to this or our other
mailing lists, please see the Vienna Wireless Society web site:
http://www.viennawireless.org/lists.php