While "not really control", I am using APRSIS32, ONLY the development version please, to interact with the APRS side of D7120GA I own. I mean, unlike using DXLabSuite's 'Commander', to change mode(s)

Howdy. I DO have the complete, sectioned, Instruction PDF you mentioned. So after re-looking, I noticed during a Scan that the Step-Size was incorrectly 12.5Kc ... this, it turns out, was programmed i

I am pretty much certain that I have carefully read the Scan section of the D710 PDF. When I try to scan, all I get is scan through whatever frequency I am on. ....118.5 (from a lower-limit) . I will

(1) "Also" in Settings [APRS] {600} there is as mentioned by the guys here, "APRS LOCK : OFF (or ON) (2) If I press "F" briefly I get thee expected. However if I HOLD "F" for more than a second, I see

When I look on Findu, I see I haven't sent a GPS position in over a day. Yet I think I beacon several times an hour from the fixed location. I do have my precise position in the #605 memory position o

Tony, I did the Full-Reset. Decoded no packets off ,CH-A, 144.390 overnight. However, I had CH-B on 145.825 for Sat's and did copy RS0ISS traffic. CH-B is the External and is read through SignaLink vi

I figured the Full Reset out ...had to toggle Aux-999 enough to get "Full" Did that and now hoping I get some decodes. Have not imported my previous settings yet in case they were the problem. Hoping

That was my question. I do not know HOW to do a 'Full Reset'. And I didn't see it in the manual(s)

wits end. I haven't decoded any APRS/Packet via the rig for a week. I can see the trace of a strong known Digi-Peater 20 miles away ... by using a SDR dongle and looking at the waterfall trace via SDR

While using APRSIS32 with my D710GA, I was noticing I wasn't seeing any APRS decodes coming out of the 710. I had CH1 on 144.390. I had CH2 on 145.825 and that CH output being read by AGWPE/UISS .. I

KD7YZ-15 Path .. hmmm, #612 is wide1-1,wide2-1 should I have entered KG4DVE-1 . which is the only iGate at 20 miles away.

I noticed that on Findu that my last Lat/Lon update was 2 days ago. And yet I have beaconing to every 20 minutes. What's the key to setting the rig to do that? thanks

Strangest thing. This morning whenever I digipeated or Tx'd , I heard the Beep. Came back after a 30 mile run to get groceries and noticed there are no more beeps when I KNOW it is supposed to be doin

Hi Joey' It's taken me a bit to get time to check your suggestion. Sorry. However, "Carrier" helps ... IF I make the single frequency APRS 144.390 on the Internal Data Band =B the External Data Band =

Hello David So, I tried letting CH-B (right-hand as u said) scan. Then I made the D710 "BCON" (obviously by pushing that button on the face). Scanning stopped completely. Next, with CH-B scanning, I h

GM Subject pretty well states my question. Somewhere in the setup I may have missed the answer. However, it is not obvious to me. At the moment, I am scanning a handful of both 2m as well as 440 repea

set Ch B to that QRG and 9600b but was running through AGWPE and figured that was wrong protocol. Or I set the Rig up incorrectly. I can ask over on AMSAT but thought there may be another D710 using f

Yikes, Lynn ... it seems that this entire Email-List-Interface "mostly" doesn't send all emails to me. And I see nothing in "Junk/Spam" Yes, I have a D710GA ... didn't find, on my initial look, a grou

I am also using APRSIS32. However quite a while back I asked this and never heard from anyone over there. I have menu 616 Digipeat set "on" so here is a snip from the Digipeat log of APRSIS32 --------

and came back later and once again UISS will not key it. so I am am again flummoxed. -- 73 Bob KD7YZ AMSAT LM #901