Date   

Scanner on Band A and B

Gerhard Oelz <oe9goi@...>
 

Hello!

I�m a new user of the Kenwood TM-700D.
On every band (A and B) I can select the
different memorys. When I start the scanner
on both bands, the scanner will stop on the
same QRG in both Band (Memory 3 - 145.650).
Is it possible to scan on Band A only QRG of
2m and on Band B only QRG of 70cm?

Is my rig broken, is it a bug or should it
be a feature?

vy 73 de Gerhard


Re: TM-D-700A Deviation

Kiely Petersen <zl1wpk@...>
 

To save me and you a lot of time I get you to have a look at the mod site
where I found it http://www.mods.dk/

I have yet to find out if it works and yes be careful !!


btw : The only thing I have adjust is the deviation

----- Original Message -----
From: Karl S <kg4bna@arrl.net>
To: <TMD700A@egroups.com>
Sent: Wednesday, 23 August 2000 21:07
Subject: TM-D-700A Deviation


Kiely,

How do you get it into the service mode? And are there special
precautions
we should be aware of while it is in the service mode?

Thanks,

Karl, KG4BNA


Re: TM-D-700A Deviation

Karl S <kg4bna@...>
 

Kiely,

How do you get it into the service mode? And are there special precautions
we should be aware of while it is in the service mode?

Thanks,

Karl, KG4BNA

-----Original Message-----
From: Kiely Petersen [mailto:zl1wpk@ihug.co.nz]
Sent: Wednesday, August 23, 2000 2:58 AM
To: TMD700A@egroups.com; sseeger@stellartec.com
Subject: [TMD700A] TM-D-700A Deviation


I think I have found out how to adjust the deviation (well it adjust the
figures and numbers) by going into the service mode then to the transmission
deviation part then press and holding the Mic PTT in then move the tuning
control up or down. Then set.



Kiely ZL1WPK

-----Original Message-----


Hi

I have just got the Kenwood TM-D-700 and have been told that it has got low
modulation I have TRY to adjusted it by the service mode but cant seem to
move the deviation with < and > buttons all that does is scroll through the
options am I doing some wrong?

Any help would be appreciated

Kiely ZL1WPK


btw I have the MC-53DM microphone




Community email addresses:
Post message: TMD700A@onelist.com
Subscribe: TMD700A-subscribe@onelist.com
Unsubscribe: TMD700A-unsubscribe@onelist.com
List owner: TMD700A-owner@onelist.com

Shortcut URL to this page:
http://www.onelist.com/community/TMD700A


TM-D-700A Deviation

Kiely Petersen <zl1wpk@...>
 

I think I have found out how to adjust the deviation (well it adjust the
figures and numbers) by going into the service mode then to the transmission
deviation part then press and holding the Mic PTT in then move the tuning
control up or down. Then set.



Kiely ZL1WPK

-----Original Message-----


Hi

I have just got the Kenwood TM-D-700 and have been told that it has got low
modulation I have TRY to adjusted it by the service mode but cant seem to
move the deviation with < and > buttons all that does is scroll through the
options am I doing some wrong?

Any help would be appreciated

Kiely ZL1WPK


btw I have the MC-53DM microphone


Re: Digest Number 85

phil yanov <phil@...>
 

I have not. Hopefully someone else in the group has done this before.
-philip [KG4FOZ]

Has anyone found a way to vary the delay before scan
resumes after carrier drops?
Thanks,
Jerry
VE3DKD


TM-D700A Deviation

Kiely Petersen <dazzie@...>
 

Hi

I have just got the Kenwood TM-D-700 and have been told that it has got low
modulation I have TRY to adjusted it by the service mode but cant seem to
move the deviation with < and > buttons all that does is scroll through the
options am I doing some wrong?

Any help would be appreciated

Kiely ZL1WPK


btw I have the MC-53DM microphone


Carrier Operated Scan - Resume Delay

jbishop <jbishop@...>
 

Has anyone found a way to vary the delay before scan
resumes after carrier drops?
Thanks,
Jerry
VE3DKD


site update

Robert Voerman <r.voerman@...>
 

http://members1.chello.nl/~r.voerman/

Cu Robert

Http: http: //members1.chello.nl/~r.voerman/
Email : r.voerman@chello.nl
AX25 : pd0pvl@pi8apd
Email : pd0pvl@amsat.org


Kenwood D-700 APRS Speech Contest (deadline extended)

Keith Sproul <ksproul@...>
 

The deadline is September 18th. Please send in your entries.

===================================================================
==== Kenwood D700 APRS(tm) Speech Message Contest ====
===================================================================

The Kenwood TM-D700 Radio has the ability to have a speech synthesizer
added to it. If you add this option, you can make the D700 'SPEAK' or
actually 'SPELL' APRS messages.

When you send a message to a D700 with the VS-3 Speech chip, it will SPELL
the call sign of the station that sent the message.

In addition to this, if you put a percent sign '%' as the FIRST character
of a message, it will SPELL the letters and numbers of the message.

For example, if I send the following message from WU2Z to WB4APR,

%ICU2

Bob will hear:

DOUBLE-YOU YOU TWO ZED I SEE YOU TOO


We are announcing a contest to see what kind of messages people can come
up with for using this neat feature of the Kenwood TM-D700 radio and the
VS-3.

===================================================================
Rules for the contest:

* There will be three categories:

The LONGEST message that makes sense.

The MOST TECHNICAL message.

The most original or funniest message.

* The winners will be announced at the ARRL Digital Communications
Conference in Orlando, FL, September 23, 2000.

* Each winner will receive a $50 gift certificate from Kenwood Radio.

* APRS Authors and Kenwood employees are not eligible.

* The judges will be the APRS Authors and Kenwood personnel that are
present at the September 2000, ARRL DCC in Orlando, FL.

* All decisions of the judges will be final.

* All entries must be sent by email ksproul@noc.rutgers.edu by September
18th, or delivered in person at the DCC.

* PLEASE put D700 CONTEST as the subject of the email!!!

* You must have a valid Amateur Radio License to enter.

* You do NOT need to own a Kenwood D700 or VS-3 to enter.

* You do NOT need to be a registered user of any version of APRS to enter.

* You do NOT need to be present at the ARRL DCC to win.

* In case of a tie, i.e. exact or very similar duplicate message the
earliest received entry will win.

* In case of other ties, the judges opinions will determine the winner.

* All entries can be used by Kenwood and/or the APRS authors for demo
and/or advertising purposes. All entries will be posted on the Web after
the contest, with your call sign to give you credit.

* Entries that imply profanity or inappropriate content will be ignored.

===================================================================


The documentation for the Speech functions of the D700 are at:

http://aprs.rutgers.edu/D700Voice.html

There is also a copy of it at:

http://dorm.rutgers.edu/~ksproul/D700Voice.html

(If one is down, try the other, I will keep them both updated)

If you have questions about this contest, or how the Voice option works,
please send email to me at: ksproul@noc.rutgers.edu

As questions come in, I will update the documentation if needed.

You may distribute this announcement to other places, but you must leave
it exactly as is.


--
Keith Sproul Ham Radio: WU2Z
WinAPRS/MacAPRS/X-APRS Author
http://dorm.rutgers.edu/~ksproul/ mailto://ksproul@noc.rutgers.edu
Keith Sproul 732 445-3695 Office
Student Housing Network Coordinator 732 445-2968 Fax
mailto:ksproul@rci.rutgers.edu 732 821-4828 Home
http://dorm.rutgers.edu/~ksproul/ WU2Z


Scan Speed

J & D Schnoor <schnoor@...>
 

Can anyone advise me how fast the TM-D700 scans through the memory channels?

Jim AA0FJ


Re: Multiple NMEA output

Christopher A Gilbert <cagilber@...>
 

I have done this with a GPS III+ and a different "home-brew" GPS unit.
Seems to be working fine. I have run my D-700/D-7 and my laptop running
SA and have not noticed any problems.
Chris
KB9LTH

Message: 3
Date: Fri, 04 Aug 2000 01:39:09 -0000
From: "Philip Yanov" <phil@philyanov.com>
Subject: Multiple NMEA output

I have this idea that I might like to use my Garmin GPS III+ so that
I can use it with both my D700 and very occasionally with a laptop
running Map 'n' Go. The book with the GPS III+ indicates that it
will drive up to 3 NMEA devices simultaneously. I am thinking of
splicing the seriel cable such that I could leave the cable hooked to
my D700 all of the time and attach a serial cable to my serial port
on my PC when I want to use it for navigation.

My question is this -- Has anyone else done this? Can anyone think
of a reason that it won't work?


Vraagje

Wim Zonneveld <zonneveld@...>
 

Kan iemand mij wellicht helpen aan de handleiding van de TMD700E en dan nog het
liefst in het Nederlands ? Ik heb namelijk een TMD700E gekocht bij de firma in
Katwijk, echter zonder handleiding.
Alvast dank
 
Wim Zonneveld, pa2wjz
 
 
------------------------------------------------------------------------------------------------------------
W.J. Zonneveld jr.
Vereniging de Muurkrant
Postbus 10387
2501 HJ  DEN HAAG
Telefoon    : 070 - 364 89 10
Fax          : 070 - 346 12 92
e-mail       : zonneveld@...
ICQ          : 27085817
http://www.muurkrant.nl
----------------------------------------------------------------------------------------------------------------     
Gratis informatie en aanbiedingen ontvangen en nog geld verdienen ook. Dat
is EuroClix, een gloednieuw internet-spaarprogramma. EuroClix werkt heel
eenvoudig: je meldt je gratis aan via http://www.muurkrant.nl
en via de EuroClix-website en e-mails ontvang je dan
informatie en aanbiedingen op maat, afkomstig van gerenommeerde bedrijven en
organisaties als Ford, Philips, Algemeen Dagblad, QXL, Scoot, etc.
---------------------------------------------------------------------------------------------------------------------


Re: Multiple NMEA output

Samuel Barker <srbarker@...>
 

I've done this with a Garmin GPS 35, and it works fine.  I have the gps wired to my D700, and a DB9 spliced off from that (or is the radio connector spliced from the DB9?  Either way).  I run a Topo mapping program on a laptop, and APRS through the D700 simultaneously.
 
Samuel, W7YYY
-----Original Message-----
From: Philip Yanov [mailto:phil@...]
Sent: Thursday, August 03, 2000 7:39 PM
To: TMD700A@...
Subject: [TMD700A] Multiple NMEA output

I have this idea that I might like to use my Garmin GPS III+ so that
I can use it with both my D700 and very occasionally with a laptop
running Map 'n' Go.  The book with the GPS III+ indicates that it
will drive up to 3 NMEA devices simultaneously. I am thinking of
splicing the seriel cable such that I could leave the cable hooked to
my D700 all of the time and attach a serial cable to my serial port
on my PC when I want to use it for navigation.

My question is this -- Has anyone else done this?  Can anyone think
of a reason that it won't work?



Community email addresses:
  Post message: TMD700A@...
  Subscribe:    TMD700A-subscribe@...
  Unsubscribe:  TMD700A-unsubscribe@...
  List owner:   TMD700A-owner@...

Shortcut URL to this page:
  http://www.onelist.com/community/TMD700A



**********************NOTICE****************************

DO NOT read, copy or disseminate this

communication unless you are the intended addressee.

This e-mail communication contains confidential

and/or privileged information intended only for the

addressee. If you have received this communication

in error, please call us (collect) immediately at

(208) 344-7811 and ask to speak to the sender. Also,

please e-mail the sender to notify him/her immediately

that you have received the communication in error.




Re: VS-3 and aprs

Keith Sproul <ksproul@...>
 

Go MENU, and look at the options for the VOICE..

There is a SPEAK ALL and SPEAK APRS ONLY options..

When someone sends you a message it SHOULD say the call sign of the sender..

Also, if the message starts with '%', it should spell the message..

Check out:

http://dorm.rutgers.edu/~ksproul/D700Voice.html

What do I have to set in the D700 to have the voice synthesizer read out the
callsigns and messages in the aprs mode?

It does speak the commands, but does not work with the aprs information.

- Steve
Keith Sproul 732 445-3695 Office
Student Housing Network Coordinator 732 445-2968 Fax
mailto:ksproul@rci.rutgers.edu 732 821-4828 Home
http://dorm.rutgers.edu/~ksproul/ WU2Z


Multiple NMEA output

Philip Yanov <phil@...>
 

I have this idea that I might like to use my Garmin GPS III+ so that
I can use it with both my D700 and very occasionally with a laptop
running Map 'n' Go. The book with the GPS III+ indicates that it
will drive up to 3 NMEA devices simultaneously. I am thinking of
splicing the seriel cable such that I could leave the cable hooked to
my D700 all of the time and attach a serial cable to my serial port
on my PC when I want to use it for navigation.

My question is this -- Has anyone else done this? Can anyone think
of a reason that it won't work?


VS-3 and aprs

Steve Siesel <steve@...>
 

What do I have to set in the D700 to have the voice synthesizer read out the
callsigns and messages in the aprs mode?

It does speak the commands, but does not work with the aprs information.

- Steve


Re: Control Software

Sergio Gallego <eb4cpk@...>
 

I visit this site and found Md700100.exe file i download it and it�s working
fine. If you don�t could download it i send you by mail. Thank for your
interesting. 73�s form EB4CPK


Re: Control Software

Philip Yanov <phil@...>
 

The software MD700100.exe is usually available via the Kenwood ftp
site. (ftp.kenwood.net) The problem is that the site has been down
today. This is the first time I have ever seen it down, but it is a
bit frustrating.

If you are in a hurry, send me an email, and I will reply with the
file. It is just over 1MB in size, so it will take a little while to
download if you do not have high-speed internet access. -73 KG4FOZ

--- In TMD700A@egroups.com, eb4cpk@w... wrote:
Hello I´m searching for soft to controller the D700. Thank´s.


Cross-band audio

mark@...
 

There was a post earlier about someone getting muddy audio when using
cross-band repeat. I too am having this problem. Looks like a
design flaw.

-- has anyone found a solution or workaround for this problem?

Thanks for your help.

Mark


Re: Control Software

JERRY ROCHELLE <k5qm@...>
 

try kenwood.com, that's where i found software.
jerry k5qm

eb4cpk@wanadoo.es wrote:

Hello I�m searchig for soft to controler the D700. Thank�s.

Community email addresses:
Post message: TMD700A@onelist.com
Subscribe: TMD700A-subscribe@onelist.com
Unsubscribe: TMD700A-unsubscribe@onelist.com
List owner: TMD700A-owner@onelist.com

Shortcut URL to this page:
http://www.onelist.com/community/TMD700A

13261 - 13280 of 13568