Date   

Re: Best Way to Change Configurations TM-D710G?

Mike Rees, 2004 SYA 40' 71616
 

Use the PM memories. 

On Wed, Aug 5, 2020 at 08:12 Charles Jessee <cbjesseeNH@...> wrote:
I use my TM-D710G for numerous purposes, including APRS & Winlink. At present, I have different configuration files saved in the MCP-6A memory control program directory and download those to my radio as needed. Is there a better way? My TH-D74a has an onboard miniSD card to make this method easy but not the TM-D710G.

Bret/N4SRN

--
73
Mike
N6YSK
ARRL VEC


Best Way to Change Configurations TM-D710G?

Charles Jessee
 

I use my TM-D710G for numerous purposes, including APRS & Winlink. At present, I have different configuration files saved in the MCP-6A memory control program directory and download those to my radio as needed. Is there a better way? My TH-D74a has an onboard miniSD card to make this method easy but not the TM-D710G.

Bret/N4SRN


locked Re: Unsubscribe (was: Kenwood Parts Source)

Larry J. Ford K4AEC
 

You may need to navigate to the group website to remove yourself.  You may have signed-up with a password that is required to "unsubscribe" you.

Unless an administrator of the list sees your message, simply posting it to the main list (especially with a Subject Line of "Kenwood Parts Source"), going out to all subscribers may not do any good, as there is nothing we can do to unsubscribe YOU.

Larry J. Ford
K4AEC
 



------ Original Message ------
Received: 12:53 AM EDT, 08/04/2020
From: "Greg via groups.io" <gdmorris707@...>
To: "TMD700A@groups.io" <TMD700A@groups.io>
Subject: Re: [TMD700A] Kenwood Parts Source


Please remove me from the group. Thank you. I have enjoyed many years. Peace to all. 





Re: Kenwood Parts Source

Lee Besing
 

Greg, simply click on the unsubscribe link that is at the bottom of every message


Lee Besing, N5NTG
210-771-7075
San Antonio TX


-----Original Message-----
From: "Greg via groups.io" <gdmorris707@...>
To: "TMD700A@groups.io" <TMD700A@groups.io>
Sent: Mon, 03 Aug 2020 11:52 PM
Subject: Re: [TMD700A] Kenwood Parts Source

Please remove me from the group. Thank you. I have enjoyed many years. Peace to all. 


Re: Kenwood Parts Source

Greg <gdmorris707@...>
 

Please remove me from the group. Thank you. I have enjoyed many years. Peace to all. 


Re: Kenwood Parts Source

Jonathan Poland
 

Thank you everyone.  I have the parts on order from PacParts.

jon N0WL


Re: D700A help with ribbon cable connector

Joseph LaFerla
 

HI Leo

After a very long wait looking for part numbers and parts, I have finally been able to get the connector soldered in place.  I first contacted Kenwood USA who gave me the part number and that I could get it through East Coast Transistor and Parts. I sent the radio to a local repair shop since the connector is smd and very tiny.  The repair shop guy tells me that, once the connector was soldered in, the radio immediately powered up and the tnc now works.  So it would seem that something in the bootloader goes around looking for each component and will hang until it finds everything.  Although it took much longer, especially since I live in Canada, I preferred to wait until the exact replacement part was received rather than getting one from Digikey.  I actually bought two connectors and will keep one as spare just in case.

Thanks for your help and suggestions to all who provided input.  

Joe VA3JLF


Re: Kenwood Parts Source

 

Try EAST COAST TRANSISTOR PARTS

       2 MARLBOROUGH ROAD

      WEST HAMPSTEAD, NY 11552

       PHONE 1-516-483-5742

       FAX 1-516-483-5904

 

I have gotten many parts from them

 

Ron K1VSC

 

Sent from Mail for Windows 10

 


Re: Kenwood Parts Source

Jay
 

Pacific Coast Parts still carry those.
www.pacparts.com

73, Jay KC0JAN


From: TMD700A@groups.io <TMD700A@groups.io> on behalf of Jonathan Poland <jonpoland@...>
Sent: Saturday, August 1, 2020 6:09:34 PM
To: TMD700A@groups.io <TMD700A@groups.io>
Subject: [TMD700A] Kenwood Parts Source
 
Hello,

My son dropped his TM-D710 control head and broke off one of the right-hand knobs.  I am looking for the part number and source for the knob module.  (Also replacement knobs...)

Thanks in advance,

Jon Poland, N0WL


Kenwood Parts Source

Jonathan Poland
 

Hello,

My son dropped his TM-D710 control head and broke off one of the right-hand knobs.  I am looking for the part number and source for the knob module.  (Also replacement knobs...)

Thanks in advance,

Jon Poland, N0WL


Re: TNC ERROR - D710GA

Rich Cite Tow
 

Thanks Randy. 73 Rich KK6CCR


On Thu, Jul 23, 2020, 09:03 Randy Allen <ka0azs@...> wrote:
Yes.

I did mine a couple of years ago (TM-D710A)

I got the battery (Part#  881Z76-7648-72) from PacParts: https://www.pacparts.com/

Here's a website with some pictures:

https://bubbazanetti.blogspot.com/2013/06/kenwood-d-710-backup-battery-change.html

Hope this helps

73

Randy, KA0AZS


Re: TNC ERROR - D710GA

Randy Allen
 

Yes.

I did mine a couple of years ago (TM-D710A)

I got the battery (Part#  881Z76-7648-72) from PacParts: https://www.pacparts.com/

Here's a website with some pictures:

https://bubbazanetti.blogspot.com/2013/06/kenwood-d-710-backup-battery-change.html

Hope this helps

73

Randy, KA0AZS


Re: TNC ERROR - D710GA

Rich Cite Tow
 

do I remove the rear case to replace the batteries?


Re: Looking for Computer control software for the TM-D710G

KD7YZ Bob
 

On 7/21/2020 22:10, Emory Haines wrote:
Anyone know of software to control the TM-D710G?  
Thank you  73  Emory  WM3M
While "not really control", I am using APRSIS32, ONLY the development
version please, to interact with the APRS side of D7120GA I own.

I mean, unlike using DXLabSuite's 'Commander', to change mode(s) and
QRG, APRSIS32 can't do that ... and Commander can't seem to do anything
or talk to the D710. And I love thge DxLabSuite stuff.

Also, I own Packet-Engine-Pro which reads and decodes the 'External Data
Output' of the D710Ga here. That and UISS will allow work through the ISS.

But still, it isn't the 'Control' which you are asking about.

As I 'mostly' use the D710 for APRS, I am getting along, but would
prefer the control too.

Prolly, the CAT interface from the Kenwood and the dual-band ops, might
make it a nightmare for the overworked programmer of DxLabSuite ...
considering the DxLabSuite is freeware. I am a former programmer of
intercept and analysis equipment and , in a way, can sympathize with
him. The difference was, I was compensated for hours of work ,, hi hi .



--
73
Bob KD7YZ
AMSAT LM #901


Looking for Computer control software for the TM-D710G

Emory Haines
 

Anyone know of software to control the TM-D710G?  
Thank you  73  Emory  WM3M


Re: Unable to make D710GA Group or Program Scan work

KD7YZ Bob
 

On 7/18/2020 01:02, Mark Wolff wrote:
Good evening Bob -
Howdy.


Presume you are referring to Sec 4 / Scan as the PDF mentioned?  Your
description suggests you are executing a "MHz scan"?

I DO have the complete, sectioned, Instruction PDF you mentioned.

So after re-looking, I noticed during a Scan that the Step-Size was
incorrectly 12.5Kc ... this, it turns out, was programmed into one of
the VFO-Screens. Even tho 25KC was in the memories table. So I changed
all the VFO-tabs to be 25Khz.

Then a form of VFO scan started.

Next I notice that I AM on the correct Band ...namely 118MHz band.

HOWEVER, a scan starts at 118 and goers as for as 129.975 then restarts
at 118.025 again.

This appears to mimic a Limit-Memories L0-U0 selection.

Since it isn't possible to link all the Limit-Memories, I can't get past
a VFO Scan of being tied to Limit-Memories.

You worked that one out?

There were, for my Locale, two or three frequencies that seemed to be a
modulated single tone that was both strong as well as constant. So I
tried to split up the limit-memories.

In any event, according to VFO-Scan, If I put myself (VFO, on anything
in the 118 Band, which ostensibly goes through 136 MHZ, that I should
scan 118 to 1`36 ....according to VFO Scan ...

right??

cuz it "ain't" doing that.

hopefully two memory-tables from my D710 will come through. A pix is
worth a thousand words ...








--
73
Bob KD7YZ
AMSAT LM #901


Re: Unable to make D710GA Group or Program Scan work

Mark Wolff
 

Good evening Bob - Coincidently, I just stumbled across the detailed 710 instruction manual on CD that I lost some time back. Mine is an earlier 710A but assume it works the same in Scan mode as the G model.

Presume you are referring to Sec 4 / Scan as the PDF mentioned?  Your description suggests you are executing a "MHz scan"?  Page "Scan-3 " depicts the somewhat detailed steps for a "Program Scan" using a pre-programmed pair of low to high frequencies (Lx to Ux where x is an integer from 0 to 9).  If you don't have this document, happy to send you a copy?

73

MW / N4MEW
904.616.2004


On Fri, Jul 17, 2020 at 9:31 PM KD7YZ Bob <kd7yz@...> wrote:
I am pretty much certain that I have carefully read the Scan section of the D710 PDF.

When I try to scan, all I get is scan through whatever frequency I am on. ....118.5 (from a lower-limit) .
I will only see the last of three numerals, blink, and the scan goes through only that MHz range ... I am interested in a L0 through U0, in the Aircraft band L0=118.00 and U0=121.400

I see the "1" then scan thru 121.0 to 121.975'ish then repeat.

any help?


--
--
Bob KD7YZ
TM-D710GA




Unable to make D710GA Group or Program Scan work

KD7YZ Bob
 

I am pretty much certain that I have carefully read the Scan section of the D710 PDF.

When I try to scan, all I get is scan through whatever frequency I am on. ....118.5 (from a lower-limit) .
I will only see the last of three numerals, blink, and the scan goes through only that MHz range ... I am interested in a L0 through U0, in the Aircraft band L0=118.00 and U0=121.400

I see the "1" then scan thru 121.0 to 121.975'ish then repeat.

any help?


--
--
Bob KD7YZ
TM-D710GA


Re: GPS Unit for D710A Correction

 

I use one of three GPS units all interchangeable with my radios,

  1. Magellan Sport Track
  2. Garmin GPSMAP 478
  3. Garmin Rhino 130

 

Only small adjustments to radio setting is necessary to have them work with my TMD 700A(G), THD7A(G) and TM-271A, the setting? Is the baud rate!

 

Ron K1VSC

 

Sent from Mail for Windows 10

 


Re: GPS Unit for D710A Correction

Rob Erikson <rperikson1@...>
 

Correction to my last reply. I listed the wrong GPS. It is the unit with the serial cable.


Garmin 18x PC GPS Navigator Unit

https://www.amazon.com/Garmin-18x-GPS-Navigator-Unit/dp/B0016NYHVS/ref=sr_1_4?dchild=1&keywords=Garmin+18x+USB+GPS+Navigator+Unit&qid=1594598924&s=electronics&sr=1-4

73,
Rob - KG4OPX


201 - 220 of 13653