Not mine , just passin on https://reno.craigslist.org/tls/d/gardnerville-southbend-lathe-9a/7626658441.html animal

Maybe the one on the left is smaller animal

https://www.facebook.com/marketplace/item/770078051088911/?mibextid=dXMIcH I asked seller for details. Too big for my shop. Lodge and Shipley 18"

I made some levelers from 2" x 3/8" flat stock. I drilled a large divot in the center then epoxied a 1/2" carriage bolt in the divot. I then took a nut threaded it onto the bolt, then 2 heavy washers

I am finally getting my 1969 16" lathe running after moving to my new shop over the last 18 months. I figure its a good opportunity to fix my pesky oil leak at the apron. It is leaking at the back pla

I am putting a model 37 back into service. About 40 years of its life was just sitting at my dad's garage. He had modified it to run off a 220v 1PH motor tied to a truck 4 spd transmision by dual v be

Now I know that for some folks parting off in the lathe is routine, but for some of us it's a real PITA. Or can be. I've tried using a nice HSS blade in a holder with lots of oil and freshly-ground ti

I made these before, parted off using a hss blade. The cuts were somewhat dished, but it was an interrupted cut with the slots already there.

Hey Guys: I'm starting to feel my age lately and not been very active here for quite a while. I haven't gotten any response from C.L. so I thought I'd try here next. I have a very large collection of

I posted a while back about needing to cut a slot without a milling machine; I thought I'd circle back and let you all know how it worked out. The part I made is the back-gear engagement shoe for a Je

I sell collectable comics and mags via eBay and have kicked this dead horse down the street many times. My *experience* is also that Media Mail items can go missing, even with tracking. I sold a DVD i

Son and I rebuilding 14-1/2’’ and need apron hand wheel, can't find an original but can get a cast iron wheel that looks close fairly cheap. Can someone tell us the size of original wheel, part book n

Hello all. I am looking for a source for HSS inserts to fit a particular lathe tool I bought not long ago from Shars. The tool (MWLN Tri-lock tool) came with a carbide insert (WNMG 332) but no matter

Where do you guys find the best deals on bulk fasteners? Sometimes we find a good price at Home Repot or Lowes for 25# containers of deck screws, but we've been using a lot of the Timberlok and simila

Hot min , just passin on . Looks like a pretty clean 9C https://reno.craigslist.org/tls/d/gardnerville-vintage-southbend-lathe/7607898813.html animal

I don't need these for my lathe but they are inexpensive and might work for others with older lathes or even for any gearing projects. Seems like this Vevor brand is really ramping up to try and be a

I have a Heavy 10 with a 36” bed, large through hole, set up for C collets. Has a 3-jaw chuck on it. A 4-jaw comes with it but needs the backer plate changed to fit the lathe. 3-phase motor comes with

A while back, okay almost 20 years ago, a friend worked at Jorgenson Steel in Denver. You know how that mill oil on steel is... He and I and a roommate started a floor cleaning business and did the fl

Hello, I have two AXA size toolposts that I am tired of looking at. Both are piston type, One is brand new still in grease paper and the other one has been mounted on a lathe and barely used. I would

For someone that needs a good variable speed, reversable setup, I am offering a Baldor IDXM7006 inverter duty ½ HP motor and TECO Westinghouse L510-101-H1-U Variable Frequency Drive for sale. See atta