Cheri says, “ Good JOB!” S. Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com NOTICE: This E-mail (including attachments) is covered by the Electronic Co

Yeah . . . I’m screwed . . . with any luck . . . Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com NOTICE: This E-mail (including attachments) is covered

Paul, that length, to be clear is 12-5/8” from the tip of the threaded shaft to the outside edge of the nut securing the handle. Doesn’t sound like a fit, given the 8 tpi, but Rick and I continue to a

Okay, Paul. OAL is 12-5/8”; 10 tip; diameter is 0.435”. (just missed 7/16, I guess. Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com NOTICE: This E-mail

Paul, Hi. Steve here. (Rick’s friend) Is that by any chance a large dial cross slide feed? Rick has a large dial he could modify, but we’re trying to figure out all the steps necessary so we don’t get

True enough. True enough . . . Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com NOTICE: This E-mail (including attachments) is covered by the Electronic

Glenn, that’s not a bad idea. I’ll give him a shout! Thanks! Yaz Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com NOTICE: This E-mail (including attachm

Allan, that is EXACTLY what first came to mind when I saw the shaft section protruding from the handle was hollow, and I didn’t even know I already had a stub in place, since it was entirely inside th

I would do that, George, but indicating on a piece of drill rod suggests my chuck runs out 3-5 thou’ all by itself, so I’m not sure how we’d separate the wheat from the chaff on that screw. I can try

“Born in the USA”. New computer keyboard. Gives me fits. Pun unintentional, but I’m not above that. Yaz Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com

Hey, Freehold!! Like your famous neighbor, my lathe was “boring in the U.S.A.” Hoping to find a replacement screw abroad, if not here. Yaz Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55

Not a clue, George. First I was doing some gentle facing off, and then I wasn’t(!) Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com NOTICE: This E-mail

Yup-pers! That’s why it was so helpful to learn how to get it out. Allan, to me it looks like: press get on unthreaded end of cross-slide screw, insert sc rew assembly, slide bushing over screw shaft

That should read: OD of crossfeed gear. NOT crossed gear. Sorry! Yaz Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com NOTICE: This E-mail (including att

And with the pictures, some numbers: Screw threads are 10 tpi Screw OD to outside of acme thread- 0.435” OD of unthreaded shaft at gear- 0.373" OD of crossed gear- 0.691” Length of. “ - 0.457” OAL of

Thanks, Rick. I’ll be pulling the cross-slide off tonight and photographing it, and I’ll post those. Thanks for posting the pictures taken when the lathe was clean(!) Wouldn’t want the group getting t

Tanks, Jim. Much appreciated! Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com NOTICE: This E-mail (including attachments) is covered by the Electronic

Stevan S. Yasgur Suite 550 3300 Edinborough Way Edina, MN. 55435 (952) 893-9393 steve@yazlaw.com NOTICE: This E-mail (including attachments) is covered by the Electronic Communications Privacy Act, 18

Jim, here’s a test post. I do NOT see any of Rick Kruger’s posts/responses from earlier today. Steve