Date   

Re: Milling Attachment

gorvil
 

Hi Okey,



I bought a set of the MLA castings from someone on this list and got the leadscrew and nut from another most generous member of the list.

Yoy only need the milling base if you also plan to mount the unit on a T-slot cross slide. The basic milling attachment casting set mounts in the compound spigot hole. The base plate has a spigot hole and can be bolted down on the T-slot cross slide.



I just finished my T-slot cross slide so I guess the next project will be the base.



Cheers!



Glen Reeser

--- In southbendlathe@yahoogroups.com, "Okey Caynor" <cal5@f...> wrote:

Does anyone in the group have any experience or comments on the milling
attachment for the 9" SB at
http://www.statecollegecentral.com/metallathe/index.html ? As far as I can
tell from the description of the castings there, it appears that one would
need the ML-5 and the S4382A milling base, plus the acme nut for a total of
around $150 plus shipping. Just curious if anyone has gone this route.
Okey


Re: QC tool posts: KDK vs. Aloris?

gorvil
 

The piston type has a cam driven piston that comes out normal to the face of the dovetail. The wedge type has a dingus that expands the width of the dove tail. The wedge should be more repeatable and less suject to wear, I guess. For my home shop chip making, I don't think I would improve chip quality that much with the wedge.



Glen Reeser

I got the ENCO flyer today also. My question is, whats the difference
in the piston and the wedge in that Phase II ad? Besides almost
double the price. Theres almost no difference in appearance in the
little picture.
I also would like to update the old lantern toolpost, but until
these import quick change came along and then started to discount
them, I couldnt justify the cost (Well, ah, er, that is the wife
couldnt justify). Anyway, some explanation on these two types would
be greatly appreciated.
I too think ENCO has a better quality than Harbor Frt.
Bill Pace


threading/feed index plate

rgpeer53
 

found my plate at meridian machine,mohntown pa. 610-656-0449. or email
dave@mermac.com. does not have the fancy red coloring but looks like
whats on his web page. paid 26.75 del. mine was for 9 in if there is a
difference bettween 9 or 10 in. ps buy extra drive in rivets, wish i
had and pre bend plate to conture of gearbox. hope this helps good luck
rick


Re: QC tool posts: KDK vs. Aloris?

gabil1980 <gabil@softdisk.com> <gabil@...>
 

--- In southbendlathe@yahoogroups.com, "Glen Reeser <Gorvil@a...>"
<Gorvil@a...> wrote:
I know this isn't what you asked, but...

The latest ENCO flyer has the Phase II post sets for $89.00.
I bought a HF version for the same price and after fixing its
problems I have been happy with it. From all accounts Phase II
is a large step in quality above Harbour Freight.


Glen Reeser

I got the ENCO flyer today also. My question is, whats the difference
in the piston and the wedge in that Phase II ad? Besides almost
double the price. Theres almost no difference in appearance in the
little picture.
I also would like to update the old lantern toolpost, but until
these import quick change came along and then started to discount
them, I couldnt justify the cost (Well, ah, er, that is the wife
couldnt justify). Anyway, some explanation on these two types would
be greatly appreciated.
I too think ENCO has a better quality than Harbor Frt.

Bill Pace


Milling Attachment

Okey Caynor <cal5@...>
 

 Does anyone in the group have any experience or comments on the milling attachment for the 9" SB at http://www.statecollegecentral.com/metallathe/index.html   ? As far as I can tell from the description of the castings there, it appears that one would need the ML-5 and the S4382A milling base, plus the acme nut for a total of around $150 plus shipping. Just curious if anyone has gone this route.
 
Okey


Bed evaluation

qbox09
 

With regards to a 9" South Bend, how do you evaluate the condition
of the bed? I understand the use of the carriage lock to indicate
that wear is present in one area compared to an unworn part of the
bed. But how do you quantify (in .001"s) the amount of wear? How
much is too much? Can a straight edge and feeler gauge be used?

Finally, how do you evaluate a used, naked bed? Could a person file
off the ridge that forms at the top of the VEE and make a junk bed
appear to be servicable? It's a jungle out there.

Thank you.


Re: Who is jump_nkd ?

gorvil
 

Anthony,

I clicked on his name in the members list and it took me to his Yahoo
profile. I had to certify that I was 18 years or older first. It
lists his email as jumpnkd(at)aol.com. Lose the underscore.

Glen


--- In southbendlathe@yahoogroups.com, "lurchix <lurch@t...>"
<lurch@t...> wrote:
try attbi [dot] com

--- In southbendlathe@yahoogroups.com, "Glen Reeser <Gorvil@a...>"
<Gorvil@a...> wrote:
Hi Anthony,

I see a jumpnkd in the members file. His partial email is jumpnkd
(at)
a. I suspect that he's on AOL. AOL allows spaces in email
addresses. Mine on AOL is G Orvil(at)AOL. It collapses to
Gorvil
outside of AOL.

Glen Reeser


--- In southbendlathe@yahoogroups.com, anthrhodes@a... wrote:
I tried addressing this before.

When I was accepting names of people who wanted Parts List
Scans I
received a
message from "jump_nkd" indicating he was interested in
anything
relating to
an SB 13". At the time I didn't pay any attention to the
missing
"@xxx.xxx",
as AOL strips that part of the address from messages when an
AOLer
sends a
message to another AOLer I presumed that that was the
explanantion.
Since
then I've tried to contact this person directly without
success,
and I posted
the problem in one of my earlier messages to the group. I'll
give
it one last
try.

Jump_nkd , if your out there or if anybody on the list knows
who
this is,
provide me with a method by which you can be contacted.

Anthony
Berkeley, Calif.


Re: Who is jump_nkd ?

lurchix <lurch@theramp.net> <lurch@...>
 

try attbi [dot] com

--- In southbendlathe@yahoogroups.com, "Glen Reeser <Gorvil@a...>"
<Gorvil@a...> wrote:
Hi Anthony,

I see a jumpnkd in the members file. His partial email is jumpnkd(at)
a. I suspect that he's on AOL. AOL allows spaces in email
addresses. Mine on AOL is G Orvil(at)AOL. It collapses to Gorvil
outside of AOL.

Glen Reeser


--- In southbendlathe@yahoogroups.com, anthrhodes@a... wrote:
I tried addressing this before.

When I was accepting names of people who wanted Parts List Scans I
received a
message from "jump_nkd" indicating he was interested in anything
relating to
an SB 13". At the time I didn't pay any attention to the missing
"@xxx.xxx",
as AOL strips that part of the address from messages when an AOLer
sends a
message to another AOLer I presumed that that was the explanantion.
Since
then I've tried to contact this person directly without success,
and I posted
the problem in one of my earlier messages to the group. I'll give
it one last
try.

Jump_nkd , if your out there or if anybody on the list knows who
this is,
provide me with a method by which you can be contacted.

Anthony
Berkeley, Calif.


Re: Who is jump_nkd ?

gorvil
 

Hi Anthony,

I see a jumpnkd in the members file. His partial email is jumpnkd(at)
a. I suspect that he's on AOL. AOL allows spaces in email
addresses. Mine on AOL is G Orvil(at)AOL. It collapses to Gorvil
outside of AOL.

Glen Reeser


--- In southbendlathe@yahoogroups.com, anthrhodes@a... wrote:
I tried addressing this before.

When I was accepting names of people who wanted Parts List Scans I
received a
message from "jump_nkd" indicating he was interested in anything
relating to
an SB 13". At the time I didn't pay any attention to the missing
"@xxx.xxx",
as AOL strips that part of the address from messages when an AOLer
sends a
message to another AOLer I presumed that that was the explanantion.
Since
then I've tried to contact this person directly without success,
and I posted
the problem in one of my earlier messages to the group. I'll give
it one last
try.

Jump_nkd , if your out there or if anybody on the list knows who
this is,
provide me with a method by which you can be contacted.

Anthony
Berkeley, Calif.


Re: Is it a Logan, Sheldon, or SB mic carrige stop?

k3vyl
 

--- In southbendlathe@yahoogroups.com, Mark Long <morsetaper2@y...>
wrote:
I have a carriage stop that came w/ my SB 10L, but it does not hit
the "pad" on the carriage as a proper carriage stop should. I have
installed this carriage stop on a friends SB 10K and it fits
perfect. Snug to the ways and hits right on the carriage "pad".
Pics
at:http://members2.boo.net/~mlong/carrstop_1.jpghttp://members2.boo.ne
t/~mlong/carrstop_2.jpghttp://members2.boo.net/~mlong/carrstop_3.jpgBu
t I don't believe it is a SB carriage stop. A person told me it may
be a Logan or Sheldon carriage stop. Quality and fit and finish is
very nice as is typical of American made components. Even though it
didn't hit the pad on my 10L I have used it for the past 15 years and
it has worked flawlessly and consistently.I now have a proper fitting
stop for my 10L now and wish to sell it but I would like to identify
its maker before it goes up for sale.Any input or information
appreciatted.Thanks, Mark Long
I dont think its a south bend either.They are a cylindrical
form,from what I have seen.I have seen that stop before in my lathe
surfing,but I dont know where.
By the way a south bend stop for the 9&10k fits on the logan 9b.It
wont go up past the gearbox on the logan,but it does fit the bed.
RC

---------------------------------
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now


Re: QC tool posts: KDK vs. Aloris?

William Graves
 

From: "Darrell Coble" <dvcoble@frii.com>
with making things! DVC
uhh, is that DVC = Deligentia, Vis, Celeritas ?
That is how I got started into lathes!
-- - - - - - - - - - - - - - - - -
Bill Graves RKBA!
bgraves@ix.netcom.com


Re: QC tool posts: KDK vs. Aloris?

Neil Butterfield <neilbfield@...>
 

Like you I was torn between KDK and Aloris. A lot of shops around here used the KDK but availability of additional holders was limited. I finally opted for the Aloris purchasing the authentic Aloris dovetail AXA toolpost and then I have purchased other branded holders, Phase II, Enco, etc. For threading and cutoff I did purchase authentic Aloris again, the AXA-8 threading holder and the AXA-7 parting blade holder.
 
I'm very pleased with this arrangement although I may have spent a little more than necessary for a home shop.
 
Neil

----- Original Message -----
From: pacmot
Sent: Monday, January 13, 2003 12:13 AM
Subject: [southbendlathe] QC tool posts: KDK vs. Aloris?

Does anyone have some wisdom (or opinion) to pass along
about  these two types of QC tool post?

I'd like to replace the original-style rocker tool post on my SB 9"
with a more solid, convenient one - either an Aloris AXA or a KDK
0.

I like the low-profile and true two-tool-per-holder of the KDK,
but...
I am drawn to the wide availability of the Aloris-types (and the low
cost of the knock-off brands).

Any advice will be appreciated.
Thanks in advance.


--
Web: http://groups.yahoo.com/group/southbendlathe/
More pix:  http://groups.yahoo.com/group/SouthBendLathePix/
Newbie guide: http://smaa.techwood.net/SBL/Newbie.pdf
FAQ: TBD
Post: southbendlathe@...
Email Moderators: southbendlathe-owner@...
* * * * *
Manage your subscription by sending a blank message as follows:
Unsubscribe: southbendlathe-unsubscribe@...
Stop delivery: southbendlathe-nomail@...
Daily digest mode: southbendlathe-digest@...
Individual emails: southbendlathe-normal@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


Re: QC tool posts: KDK vs. Aloris?

Darrell Coble <dvcoble@...>
 

----- Hello everyone, I just bought a piston phase II for my 10K. I really
like it, it is so much more rigid compared to the old rocker type. It is
much easier and faster to make the tool change and get the tool tip set at
the right height. The down side is that this more rigid post will do more
damage when you screw up. I slipped the flat belt the other day and it is
quite tight, a Baltimore Belt Co. two ply , leather inside and woven nylon
backing to prevent stretching-nice belt.
A comment, I find that there are two important things necessary to be a good
machinist. First is knowledge of how to do the job, which you can gain from
books that I have rescued from various sources. Second is skills which
requires a lot of practise which I may never have time to learn. Have Fun
with making things! DVC


11" half nuts?

dennis pantazis
 

greetings all:

i have a pair of half nuts here, part number AS72S5D. they are not for my
10K. i think that they might be for and 11". i checked the newer parts list
scans too, nothing there for 11" so far. if anyone can confirm what model
they are for, i would appreciate it.

tia

dennis


Re: QC tool posts: KDK vs. Aloris?

gorvil
 

I know this isn't what you asked, but...

The latest ENCO flyer has the Phase II post sets for $89.00.
I bought a HF version for the same price and after fixing its
problems I have been happy with it. From all accounts Phase II
is a large step in quality above Harbour Freight.


Glen Reeser

--- In southbendlathe@yahoogroups.com, "pacmot <pacmot@y...>"
<pacmot@y...> wrote:
Does anyone have some wisdom (or opinion) to pass along
about these two types of QC tool post?

I'd like to replace the original-style rocker tool post on my SB 9"
with a more solid, convenient one - either an Aloris AXA or a KDK
0.

I like the low-profile and true two-tool-per-holder of the KDK,
but...
I am drawn to the wide availability of the Aloris-types (and the
low
cost of the knock-off brands).

Any advice will be appreciated.
Thanks in advance.


Who is jump_nkd ?

Anthony Rhodes
 

I tried addressing this before.

When I was accepting names of people who wanted Parts List Scans I received a
message from "jump_nkd" indicating he was interested in anything relating to
an SB 13". At the time I didn't pay any attention to the missing "@xxx.xxx",
as AOL strips that part of the address from messages when an AOLer sends a
message to another AOLer I presumed that that was the explanantion. Since
then I've tried to contact this person directly without success, and I posted
the problem in one of my earlier messages to the group. I'll give it one last
try.

Jump_nkd , if your out there or if anybody on the list knows who this is,
provide me with a method by which you can be contacted.

Anthony
Berkeley, Calif.


Re: Nice Repro SBL brass info plates

Kim Steiner
 

I went through the issue of replacing machine plates last year when I
restored a Van Norman mill. These things are made with a deep,
chemical etching process. To have a plate redone like the original
costs several hundred dollars. However, I discovered that some
trophy shops have the capability (or have access to someone who does)
to reproduce a graphic in black on brass. You have to prepare the
graphic, and the etching is not as deep as you will find on the
originals, but I found the result and the price (about $20) to be
quite satisfactory. Kim Steiner

--- In southbendlathe@yahoogroups.com, "persh <persh@m...>"
<persh@m...> wrote:
Some time back I paid the price and purchased a set of plates
from
South Bend. I was less than impressed with the quality of the
current production plates.

I have been thinking about making a vacuum chuck for my surface
grinder and reproducing the old style multi-colored brass plates
If you get to making some decent plates, I sure hope you'll
consider doing plates for other lathes as well . . . bigger and
smaller. If you do, count me in for at least two full sets of
plates.
I sure wish you the best of luck. Your market will be quite
small,
so don't be shy about charging what they're worth. I'm ready to
pay.


Re: QC tool posts: KDK vs. Aloris?

JS. EARLY <j.w.early@...>
 

I will put it this way, you will learn to love to hate the KDK line. The
longer you use one the less useful a single dovetail post is.
JWE
long Beach, CA

----- Original Message -----
From: <pacmot@yahoo.com>
To: <southbendlathe@yahoogroups.com>
Sent: Sunday, January 12, 2003 11:13 PM
Subject: [southbendlathe] QC tool posts: KDK vs. Aloris?


Does anyone have some wisdom (or opinion) to pass along
about these two types of QC tool post?

I'd like to replace the original-style rocker tool post on my SB 9"
with a more solid, convenient one - either an Aloris AXA or a KDK
0.

I like the low-profile and true two-tool-per-holder of the KDK,
but...
I am drawn to the wide availability of the Aloris-types (and the low
cost of the knock-off brands).

Any advice will be appreciated.
Thanks in advance.


QC tool posts: KDK vs. Aloris?

pacmot <pacmot@yahoo.com>
 

Does anyone have some wisdom (or opinion) to pass along
about these two types of QC tool post?

I'd like to replace the original-style rocker tool post on my SB 9"
with a more solid, convenient one - either an Aloris AXA or a KDK
0.

I like the low-profile and true two-tool-per-holder of the KDK,
but...
I am drawn to the wide availability of the Aloris-types (and the low
cost of the knock-off brands).

Any advice will be appreciated.
Thanks in advance.


Micrometer Carriage Stop for South Bend 9" & 10K on ebay...

Mark Long
 

I have a very nice micrometer carriage stop that fits
South Bend 9" & 10K lathes perfectly. It is
manufactured by Sheldon Lathe, a few pics in auction
now, I'll add more in a day or so with dimensions.

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3107515160

I have used it on a 10K and it fits like it was made
for them. 9" and 10K use same bed and carriage so you
can be assured of fit.

Thanks, Mark Long

__________________________________________________
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now.
http://mailplus.yahoo.com

96241 - 96260 of 104865