Date   

Re: source for replacement chuck jaws

Ondrej Krejci
 

?

Unless the chucks have two piece jaws, masters and bolt-ons, one may procure new jaws nowhere.

Good Luck,


OK

On Monday, March 22, 2021, 08:30:53 AM EDT, Jack Dinan <jack@...> wrote:


Where can I buy replacement jaws for a 1948 SB 9A?


source for replacement chuck jaws

Jack Dinan
 

Where can I buy replacement jaws for a 1948 SB 9A?


Re: Anybody close?

comstock_friend
 
Edited

The Royal nose 5C collet closer was worth the selling price. Then the threading dial. Auction closed now so someone got a deal.

John


Re: South Bend 9" lathe for sale

Ron Pare
 

The lathe is in Salem, Mass.

 

From: SouthBendLathe@groups.io <SouthBendLathe@groups.io> On Behalf Of Ron Pare
Sent: Sunday, March 21, 2021 12:28 PM
To: SouthBendLathe@groups.io
Subject: [SouthBendLathe] South Bend 9" lathe for sale

 

I have my father-in-law’s, Precision  9” Model A, South Bend  lathe (644-Y,  3ft., Circa 1945)  It originally came out of GE in Lynn, MA. 

3 and 4 jaw chucks, plates, several different types of tool holders, change gear set for metric thread cutting(I think). And a pile of ½ inch, 3/8 inch tool bit blanks and quite a few manufactured profiles.

And any other parts and bits associated with the 9” SB., includes several gallons of oil used for the lathe.

I want to sell it.  No room, No time.

PM me if interested.   $1500.00

Thanks, Ron

 


Re: Anybody close?

Ondrej Krejci
 

Howdy,

The two lathes for sale look like parts donors or fine for blacksmithing.

May be Farce be with Thee,


OK

On Sunday, March 21, 2021, 03:00:32 PM EDT, wlw19958 <wlw-19958@...> wrote:


Hi There,

Thanks Steve and Ruud.  Mine measures 10 inches so, I guess mine
hasn't been cut.  I plan on getting the holes for the set screws done later
today.

Thanks Again!
-Blue Chips-
Webb


Re: South Bend 9" lathe for sale

Bill in OKC too
 

Might want to let folks know where the lathe is located. I'm not currently in the market, but I'm sure there's going to be someone who is. 

Bill in OKC

William R. Meyers, MSgt, USAF(Ret.)


A human being should be able to change a diaper, plan an invasion,
butcher a hog, conn a ship, design a building, write a sonnet, balance
accounts, build a wall, set a bone, comfort the dying, take orders,
give orders, cooperate, act alone, solve equations, analyze a new
problem, pitch manure, program a computer, cook a tasty meal, fight
efficiently, die gallantly. Specialization is for insects.
LAZARUS LONG (Robert A. Heinlein)





On Sunday, March 21, 2021, 02:27:14 PM CDT, Ron Pare <rppare@...> wrote:


I have my father-in-law’s, Precision  9” Model A, South Bend  lathe (644-Y,  3ft., Circa 1945)  It originally came out of GE in Lynn, MA. 

3 and 4 jaw chucks, plates, several different types of tool holders, change gear set for metric thread cutting(I think). And a pile of ½ inch, 3/8 inch tool bit blanks and quite a few manufactured profiles.

And any other parts and bits associated with the 9” SB., includes several gallons of oil used for the lathe.

I want to sell it.  No room, No time.

PM me if interested.   $1500.00

Thanks, Ron

 


South Bend 9" lathe for sale

Ron Pare
 

I have my father-in-law’s, Precision  9” Model A, South Bend  lathe (644-Y,  3ft., Circa 1945)  It originally came out of GE in Lynn, MA. 

3 and 4 jaw chucks, plates, several different types of tool holders, change gear set for metric thread cutting(I think). And a pile of ½ inch, 3/8 inch tool bit blanks and quite a few manufactured profiles.

And any other parts and bits associated with the 9” SB., includes several gallons of oil used for the lathe.

I want to sell it.  No room, No time.

PM me if interested.   $1500.00

Thanks, Ron

 


Re: Collet Rack Angle

wlw19958
 

Hi There,

Thanks Steve and Ruud.  Mine measures 10 inches so, I guess mine
hasn't been cut.  I plan on getting the holes for the set screws done later
today.

Thanks Again!
-Blue Chips-
Webb


Re: Anybody close?

Steve Wells
 

It’s a 1941 model C, shop modified compound, shop modified spindle nose collet holder and closer.

Double tool slide without the slide…haha

Probably measured the swing down to the flat way, it’s a 9 inch.

 

Steve  

 

From: SouthBendLathe@groups.io <SouthBendLathe@groups.io> On Behalf Of mike allen
Sent: Saturday, March 20, 2021 11:46 PM
To: SouthBendLathe@groups.io
Subject: Re: [SouthBendLathe] Anybody close?

 

        It's a interesting lathe , maybe Ted or Steve can tell us more about it . Looks like it has a collet closer/chuck

        & a very interesting compound rest . There is a chuck in one of the pic's but you can buy a brand new chuck for under $ 200. with a backplate .

        animal

On 3/20/2021 8:30 PM, G K via groups.io wrote:

I'm close.  Can you guys tell the model from the rough photos?  Can't figure much from the description, 5"?  I am actually interested in the four-jaw chuck.  Looking for one for my SB9.  Not sure if it would fit or not.  25 miles away.

 


Re: Collet Rack Angle

Steve Wells
 

Mine measures almost the same, 10-1/8’, this is subject to how far it is threaded into the clamp bracket.

 

Steve

 

From: SouthBendLathe@groups.io <SouthBendLathe@groups.io> On Behalf Of John Dammeyer
Sent: Saturday, March 20, 2021 8:47 PM
To: SouthBendLathe@groups.io
Subject: Re: [SouthBendLathe] Collet Rack Angle

 

Here's the photo.  Excuse the mess.  Wasn't expecting company in the shop.  I've put it here rather than attaching it because this way I can give you much higher resolution so that you can zoom in to see the 10" markings on the square and the mount to the lathe bed.

 

http://www.autoartisans.com/southbend/PostHeight.jpg

 

John Dammeyer

 

From: SouthBendLathe@groups.io [mailto:SouthBendLathe@groups.io] On Behalf Of wlw19958
Sent: March-20-21 4:33 PM
To: SouthBendLathe@groups.io
Subject: Re: [SouthBendLathe] Collet Rack Angle

 

Hi There,

John, if I follow correctly, the same measurement on my assembly is 11". 
When I measure from the top of the clamp (just behind the tube) to the
base (plinth) of the collet rack casting, I get 10".

Thanks for the info!
-Blue Chips-
Webb


Re: Anybody close?

Andrei
 

That is done on purpose by some crafty sellers.

Typos are courtesy of autocorrect.


From: SouthBendLathe@groups.io <SouthBendLathe@groups.io> on behalf of William Nelson <wnnelson@...>
Sent: Sunday, March 21, 2021 11:03:58 AM
To: SouthBendLathe@groups.io <SouthBendLathe@groups.io>
Subject: Re: [SouthBendLathe] Anybody close?
 
On closer inspection that's not a 10k head stock. So I'm betting some type of 9". Can't tell if it has a quick change or if it's a A, B, or C.Those are some of the worst pictures I've seen on Ebay. Why bother when you can't even figure out what the picture is. 


Re: Anybody close?

Daughty
 

That lathe is a 1941 9" model C as it doesn't have power cross feed nor power feed. "Lacks the clutch assembly" Only half nuts for threading.


On Sun, Mar 21, 2021, 10:01 AM G K via groups.io <bug_hunter2000=yahoo.com@groups.io> wrote:
Sent a message last night.  No response as of yet.

On Sunday, March 21, 2021, 09:54:32 AM CDT, William Nelson <wnnelson@...> wrote:


Well that is not a 10k tail stock but that's all I know. Could be a 9 inch, if it was a heavy 10 the collet would be in the spindle not on the threads. Just ask the guy if you can come and inspect a lot of sellers allow that.


Re: Anybody close?

William Nelson <wnnelson@...>
 

On closer inspection that's not a 10k head stock. So I'm betting some type of 9". Can't tell if it has a quick change or if it's a A, B, or C.Those are some of the worst pictures I've seen on Ebay. Why bother when you can't even figure out what the picture is. 


Re: Anybody close?

G K
 

Sent a message last night.  No response as of yet.

On Sunday, March 21, 2021, 09:54:32 AM CDT, William Nelson <wnnelson@...> wrote:


Well that is not a 10k tail stock but that's all I know. Could be a 9 inch, if it was a heavy 10 the collet would be in the spindle not on the threads. Just ask the guy if you can come and inspect a lot of sellers allow that.


Re: Anybody close?

david pennington
 

Except for the collet adapter, it looks like the 9C in my shop. Well, not as clean, but otherwise like it.

My S/N is 167XXX, and a pic of it clearly shows the scraping on the ways. The scale and location of the S/N on the eBay machine is a match with my 9C.

-------- Original message --------
From: William Nelson <wnnelson@...>
Date: 3/21/21 08:54 (GMT-07:00)
To: SouthBendLathe@groups.io
Subject: Re: [SouthBendLathe] Anybody close?

Well that is not a 10k tail stock but that's all I know. Could be a 9 inch, if it was a heavy 10 the collet would be in the spindle not on the threads. Just ask the guy if you can come and inspect a lot of sellers allow that.


Re: Anybody close?

William Nelson <wnnelson@...>
 

Well that is not a 10k tail stock but that's all I know. Could be a 9 inch, if it was a heavy 10 the collet would be in the spindle not on the threads. Just ask the guy if you can come and inspect a lot of sellers allow that.


Re: Anybody close?

John Burt
 

I'm an hour and 10 minutes from there.
Am I gonna hafta find a place to put this thing?
Has anybody deciphered the photos? Not very clear to me.

John


Re: Anybody close?

Davis Johnson
 

I had that thought too.

The thread dial looks like a 9(a, b or c) or a 10k. So maybe a 10K?

Another possibility is they've listed the swing over the compound rather than the bed.

On 3/20/21 11:45 PM, Steven H via groups.io wrote:
I’m just guessing the the 5” is the center height so a 10” swing lathe. The Europeans like to use center height. 

Steve Haskell


On Mar 20, 2021, at 11:30 PM, G K via groups.io <bug_hunter2000@...> wrote:


I'm close.  Can you guys tell the model from the rough photos?  Can't figure much from the description, 5"?  I am actually interested in the four-jaw chuck.  Looking for one for my SB9.  Not sure if it would fit or not.  25 miles away.


Re: Collet Rack Angle

Ruud
 

Top clamp to underside base colletrack is 10” (25,5cm) on my heavy10

 

Mvg,

Ruud Silvertant

 

Van: wlw19958
Verzonden: zaterdag 20 maart 2021 22:05
Aan: SouthBendLathe@groups.io
Onderwerp: Re: [SouthBendLathe] Collet Rack Angle

 

Hi There,

Thanks Steve and Ruud!  I am surprised that the two set screws are in-line.
I would have expected something like a 90° offset between them.

Looking at the pics of Ruud's collet rack, I think my tube has been cut short. 
Would you mind measuring the distance from the top of the bed clamp to
the bottom of your rack? 

Thanks for all the help so far!
-Blue Chips-
Webb

 


Re: Anybody close?

Steven H
 

I’m just guessing the the 5” is the center height so a 10” swing lathe. The Europeans like to use center height. 

Steve Haskell


On Mar 20, 2021, at 11:30 PM, G K via groups.io <bug_hunter2000@...> wrote:


I'm close.  Can you guys tell the model from the rough photos?  Can't figure much from the description, 5"?  I am actually interested in the four-jaw chuck.  Looking for one for my SB9.  Not sure if it would fit or not.  25 miles away.

On Saturday, March 20, 2021, 03:55:58 PM CDT, William Nelson <wnnelson@...> wrote:


https://rover.ebay.com/rover/0/e11021.m43.l1120/7?euid=f81f2437c65a4b4eba8e3140b4bac368&bu=43110938583&ut=RU&segname=11021&crd=20210320044957&osub=-1~1&ch=osgood&loc=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F294073465926&sojTags=bu=bu,ut=ut,ch=ch,segname=segname,crd=crd,url=loc,osub=osub

1241 - 1260 of 105613