Date   
Re: Parting out / SB10 CL187Y / 3’ bed

Bruce
 

Ed,
Is the tail stock still available?

WTB Heavy 10 tailstock

Bruce
 

I have been working to restore a 1942 South Bend heavy 10 lathe. The tail stock that came with some parts turns out to be a 9 or 10k tail stock. It fits the ways nice but it's about an inch short. So now I am on the hunt for a proper heavy 10 tail stock. Does anyone have a spare they can part with or know of someone who does?
Thanks,
Bruce

Re: Help & Favor!!!Guenther Paul

Bill in OKC too
 

Yep, looks like he needs to change his password & run some scans on his computer. Saw the same message on a couple of the groups.io sites.

Bill in OKC

On Friday, October 11, 2019, 07:40:05 AM CDT, druid_noibn via Groups.Io <druid_noibn@...> wrote:


This is suspicious....

On Friday, October 11, 2019, 8:37:14 AM EDT, Guenther Paul <paulguenter@...> wrote:


Good Morning 

How are you doing? please i need a favor



GP

Re: Help & Favor!!!Guenther Paul

Jim_B
 

I sent a PM through the group. 
Members please don’t reply directly or your email might be compromised. 

-8
Jim B,

On Oct 11, 2019, at 9:02 AM, Jim_B <jim@...> wrote:

Looks likely. 

-8
Jim B,

On Oct 11, 2019, at 8:49 AM, Steven H via Groups.Io <stevesmachining@...> wrote:

His account has most likely been hacked. GP?

Steve Haskell

On Oct 11, 2019, at 8:39 AM, druid_noibn via Groups.Io <druid_noibn@...> wrote:

This is suspicious....

On Friday, October 11, 2019, 8:37:14 AM EDT, Guenther Paul <paulguenter@...> wrote:


Good Morning 

How are you doing? please i need a favor



GP

--
Jim B

--
Jim B

Re: Help & Favor!!!Guenther Paul

Jim_B
 

Looks likely. 

-8
Jim B,

On Oct 11, 2019, at 8:49 AM, Steven H via Groups.Io <stevesmachining@...> wrote:

His account has most likely been hacked. GP?

Steve Haskell

On Oct 11, 2019, at 8:39 AM, druid_noibn via Groups.Io <druid_noibn@...> wrote:

This is suspicious....

On Friday, October 11, 2019, 8:37:14 AM EDT, Guenther Paul <paulguenter@...> wrote:


Good Morning 

How are you doing? please i need a favor



GP

--
Jim B

Re: Help & Favor!!!Guenther Paul

Steven H
 

His account has most likely been hacked. GP?

Steve Haskell

On Oct 11, 2019, at 8:39 AM, druid_noibn via Groups.Io <druid_noibn@...> wrote:

This is suspicious....

On Friday, October 11, 2019, 8:37:14 AM EDT, Guenther Paul <paulguenter@...> wrote:


Good Morning 

How are you doing? please i need a favor



GP

Re: Help & Favor!!!Guenther Paul

druid_noibn
 

This is suspicious....

On Friday, October 11, 2019, 8:37:14 AM EDT, Guenther Paul <paulguenter@...> wrote:


Good Morning 

How are you doing? please i need a favor



GP

Help & Favor!!!Guenther Paul

Guenther Paul
 

Good Morning 

How are you doing? please i need a favor



GP

Re: What is the thread on the other end of a 9a spindle?

benjithestupiddog@...
 

Nice one thanks , I will try and get that added as a custom thread and take it from there.

Had a feeling it wouldn't be a nice common thread already modeled in Fusion.

Re: What is the thread on the other end of a 9a spindle?

jonwoellhaf
 

Mine measures 1-3/8 20. Actually measures slightly under 1.375 inches.
 

From: benjithestupiddog via Groups.Io
Sent: September 28, 2019 11:20
To: SouthBendLathe@groups.io
Subject: [SouthBendLathe] What is the thread on the other end of a 9a spindle?
 
Hi all

As per the title, can anyone conform what the thread is on the back end ( not the 11/2 - 8 end) of a 9a spindle?

I'm not great at measuring imperial threads and I'm trying to design a simple 3d printed indexing wheel.

What is the thread on the other end of a 9a spindle?

benjithestupiddog@...
 

Hi all

As per the title, can anyone conform what the thread is on the back end ( not the 11/2 - 8 end) of a 9a spindle?

I'm not great at measuring imperial threads and I'm trying to design a simple 3d printed indexing wheel.

Re: Has any one added a mill attachment to their heavy 10?

Dave Eggebraaten (AF5IA)
 

Elegant Simplicity!!!

On 9/27/2019 10:03 AM, Jim_B wrote:
I like to use the QCTP as a mount for almost any shop made attachment for my lathe. 

Here is my TP mounted “cross Drilling” fixture.
It used a chuck I had kicking around for over 30 years. 
Once set on center you can take it off or put it back without any additional work. 
I have modified it from the pictures by adding another bearing to extend the support. 
It can also be set parallel to the ways and used to drill a cirular BCD pattern. 


The Hex piece could be round. I had a chunk of hex. 
There is a slot milled in the hex. The “L” shaped holder fits the slit and is silver brazed into it. This keeps the L piece and hex “True” to each other. 

The sleeve is a sintered bronze bushing. The rod is OD ground. 
Picture shows it on a Heavy 10 but I have used it on my 9” workshop also. 

Prime power is a Dewalt Portable drill. 


I believe I have posted this before on the old site. Excuse repetition. 

Sent from my MacBook
Jim B.




On Sep 27, 2019, at 9:31 AM, Dave P. <thespamcatcher@...> wrote:

Thanks for the responses.
J
Next thing to add to the small project  list is a way to drill proper holes in the sides of parts mounted in the lathe since I don't seem to be very good at going from the lathe to the drill press and getting holes drilled correctly. I am talking about holes on the circumference of parts done on the lathe, not in line with the Z axis. 
Thanks again
Dave


--
Jim B

Re: Has any one added a mill attachment to their heavy 10?

Jim_B
 

I like to use the QCTP as a mount for almost any shop made attachment for my lathe. 

Here is my TP mounted “cross Drilling” fixture.
It used a chuck I had kicking around for over 30 years. 
Once set on center you can take it off or put it back without any additional work. 
I have modified it from the pictures by adding another bearing to extend the support. 
It can also be set parallel to the ways and used to drill a cirular BCD pattern. 


The Hex piece could be round. I had a chunk of hex. 
There is a slot milled in the hex. The “L” shaped holder fits the slit and is silver brazed into it. This keeps the L piece and hex “True” to each other. 

The sleeve is a sintered bronze bushing. The rod is OD ground. 
Picture shows it on a Heavy 10 but I have used it on my 9” workshop also. 

Prime power is a Dewalt Portable drill. 


I believe I have posted this before on the old site. Excuse repetition. 

Sent from my MacBook
Jim B.




On Sep 27, 2019, at 9:31 AM, Dave P. <thespamcatcher@...> wrote:

Thanks for the responses.
J
Next thing to add to the small project  list is a way to drill proper holes in the sides of parts mounted in the lathe since I don't seem to be very good at going from the lathe to the drill press and getting holes drilled correctly. I am talking about holes on the circumference of parts done on the lathe, not in line with the Z axis. 
Thanks again
Dave


--
Jim B

Re: Has any one added a mill attachment to their heavy 10?

Dave P.
 

Thanks for the responses.
Just and FYI, I do have a mid size mill, just not a lot of experience. The milling attachment was basically free as I got it with all of the stuff I bought from the widow of a friend a few years ago. The reason I thought about putting the milling attachment on the lathe was - I had something mounted in the mill already - mounting can be a major undertaking with the stuff and experience I have and I needed to make a quick part, but I didn't want to loose my reference on the mounted part - so I thought I would try doing it on the lathe instead, which was problematic since the milling attachment did not come with an adapter as far as I know.

Next thing to add to the small project  list is a way to drill proper holes in the sides of parts mounted in the lathe since I don't seem to be very good at going from the lathe to the drill press and getting holes drilled correctly. I am talking about holes on the circumference of parts done on the lathe, not in line with the Z axis. I have a rotary table for the mill, but I have not figured out how to use and mount it correctly yet, but that would be a big help I think.

Thanks again
Dave

Re: Has any one added a mill attachment to their heavy 10?

Stephen Bartlett
 

When I bought my 9C it was set up with a T slot cross slide. It used a hand lever for the cross motion (which did not fit properly). A regular cross slide was included, but there was no cross feed screw or compound rest. I bought a new compound rest and cross feed screw from a local SB outlet.

Then I bought a Palmgren milling attachment. I tried mounting it on the compound rest with a lantern tool post and it was very springy. I then mounted it to the T slot cross slide using T nuts, heavy bolts, and a heavy steel bar across the milling attachment's feet. That made it quite solid but I was doing only light milling.

The only downside was the nuisance of changing cross slides.

Steve Bartlett

Re: Has any one added a mill attachment to their heavy 10?

Bill in OKC too
 

Very nice work, Jim. Thanks for posting that!

Bill in OKC

On Thursday, September 26, 2019, 6:58:19 PM CDT, Jim_B <jim@...> wrote:


 I agree with Paul to a large extent. The money spent on an attachment would make a large dent in the cost of a small mill. 
I had a Burke #4 for many years. I sold it to get ready for our move to the “Olde Folks Home”. I wish I had not. 

But from time to time I need to do just a bit of milling. 

I am making a catch pan for the MG. The MG XPAG engine has a design issue that allows the rear main seal to drip oil when the engine is not running. 

Without pulling the engine and installing a modern seal, the historic fix is to add a pan that catches the oil as it drips, thus saving the garage floor. On mine I wanted to add a sight glass to see when to drain the pan. 
The pan will be made out of Al and folded and welded. The fittings for the sight glass will be welded to the side of the Pan. They needed a flat milled for welding. 

I have used a QCTP tool holder in the past as a rudimentary work holder. 

In this case I am holding a 1/2” rod, about 24” long in the tool holder. I have made several 1/32 deep passes to get a flat about 3/16 deep. 
With it still in the holder I will find center and then drill a #27 hole, in the vertical face, about 5/32 under the step, about 1/2” deep. Thats a hole that is not on center and could be difficult in another setting. The rod was then put in to the spindle, a 5/32 hole drilled in the face about 1/16 from the face. The adapter was then parted off and a 1/16 NPT thread drilled and tapped in the unmilled end. 


There is a similar adapter going on the top of the catch pan, shown to the right. This has a double step milled. 

I have not made the pan yet. I am still fitting cardboard test pieces to the curves on the bell housing., but here is what the sight gage will look like when I get the pan fabricated. 

 
Oh yes, a friend will do the TIG welding. I got rid of my welding stuff also. 😢

BI just wanted to share a possible way to do a little mill work on your lathe. 

Sent from my MacBook
Jim B.




On Sep 26, 2019, at 2:13 PM, Guenther Paul <paulguenter@...> wrote:

I would not waist my time with a milling attachment, they are not rigid enough. Buy your self a mill you will be much happier  

GP


On Thursday, September 26, 2019, 09:37:31 AM EDT, Erik S. via Groups.Io <eriks750@...> wrote:


I also have a palmgren milling attachment on my heavy 10.  I found it to move too much.  Home shop machinist article by d.e. Johnson in sept 1994 talks about improvements and how to mount.


--
Jim B

Re: Has any one added a mill attachment to their heavy 10?

Guenther Paul
 

I will have a HF big red for sale when i get my new mill with a 50" table set up. Have to do some major remodeling in my shop 

GP


On Thursday, September 26, 2019, 07:58:07 PM EDT, Jim_B <jim@...> wrote:


 I agree with Paul to a large extent. The money spent on an attachment would make a large dent in the cost of a small mill. 
I had a Burke #4 for many years. I sold it to get ready for our move to the “Olde Folks Home”. I wish I had not. 

But from time to time I need to do just a bit of milling. 

I am making a catch pan for the MG. The MG XPAG engine has a design issue that allows the rear main seal to drip oil when the engine is not running. 

Without pulling the engine and installing a modern seal, the historic fix is to add a pan that catches the oil as it drips, thus saving the garage floor. On mine I wanted to add a sight glass to see when to drain the pan. 
The pan will be made out of Al and folded and welded. The fittings for the sight glass will be welded to the side of the Pan. They needed a flat milled for welding. 

I have used a QCTP tool holder in the past as a rudimentary work holder. 

In this case I am holding a 1/2” rod, about 24” long in the tool holder. I have made several 1/32 deep passes to get a flat about 3/16 deep. 
With it still in the holder I will find center and then drill a #27 hole, in the vertical face, about 5/32 under the step, about 1/2” deep. Thats a hole that is not on center and could be difficult in another setting. The rod was then put in to the spindle, a 5/32 hole drilled in the face about 1/16 from the face. The adapter was then parted off and a 1/16 NPT thread drilled and tapped in the unmilled end. 


There is a similar adapter going on the top of the catch pan, shown to the right. This has a double step milled. 

I have not made the pan yet. I am still fitting cardboard test pieces to the curves on the bell housing., but here is what the sight gage will look like when I get the pan fabricated. 

 
Oh yes, a friend will do the TIG welding. I got rid of my welding stuff also. 😢

BI just wanted to share a possible way to do a little mill work on your lathe. 

Sent from my MacBook
Jim B.




On Sep 26, 2019, at 2:13 PM, Guenther Paul <paulguenter@...> wrote:

I would not waist my time with a milling attachment, they are not rigid enough. Buy your self a mill you will be much happier  

GP


On Thursday, September 26, 2019, 09:37:31 AM EDT, Erik S. via Groups.Io <eriks750@...> wrote:


I also have a palmgren milling attachment on my heavy 10.  I found it to move too much.  Home shop machinist article by d.e. Johnson in sept 1994 talks about improvements and how to mount.


--
Jim B

Re: Has any one added a mill attachment to their heavy 10?

Jim_B
 

 I agree with Paul to a large extent. The money spent on an attachment would make a large dent in the cost of a small mill. 
I had a Burke #4 for many years. I sold it to get ready for our move to the “Olde Folks Home”. I wish I had not. 

But from time to time I need to do just a bit of milling. 

I am making a catch pan for the MG. The MG XPAG engine has a design issue that allows the rear main seal to drip oil when the engine is not running. 

Without pulling the engine and installing a modern seal, the historic fix is to add a pan that catches the oil as it drips, thus saving the garage floor. On mine I wanted to add a sight glass to see when to drain the pan. 
The pan will be made out of Al and folded and welded. The fittings for the sight glass will be welded to the side of the Pan. They needed a flat milled for welding. 

I have used a QCTP tool holder in the past as a rudimentary work holder. 

In this case I am holding a 1/2” rod, about 24” long in the tool holder. I have made several 1/32 deep passes to get a flat about 3/16 deep. 
With it still in the holder I will find center and then drill a #27 hole, in the vertical face, about 5/32 under the step, about 1/2” deep. Thats a hole that is not on center and could be difficult in another setting. The rod was then put in to the spindle, a 5/32 hole drilled in the face about 1/16 from the face. The adapter was then parted off and a 1/16 NPT thread drilled and tapped in the unmilled end. 


There is a similar adapter going on the top of the catch pan, shown to the right. This has a double step milled. 

I have not made the pan yet. I am still fitting cardboard test pieces to the curves on the bell housing., but here is what the sight gage will look like when I get the pan fabricated. 

 
Oh yes, a friend will do the TIG welding. I got rid of my welding stuff also. 😢

BI just wanted to share a possible way to do a little mill work on your lathe. 

Sent from my MacBook
Jim B.




On Sep 26, 2019, at 2:13 PM, Guenther Paul <paulguenter@...> wrote:

I would not waist my time with a milling attachment, they are not rigid enough. Buy your self a mill you will be much happier  

GP


On Thursday, September 26, 2019, 09:37:31 AM EDT, Erik S. via Groups.Io <eriks750@...> wrote:


I also have a palmgren milling attachment on my heavy 10.  I found it to move too much.  Home shop machinist article by d.e. Johnson in sept 1994 talks about improvements and how to mount.


--
Jim B

Re: Dial Indicator Holder for 9/10k Lathe

Morris Mallard
 

If everyone who had a bad experience with this person contacts E-Bay in the same week  they will address the situation.

On Thursday, September 26, 2019, 5:07:34 PM EDT, Nfwood via Groups.Io <nfwood@...> wrote:


She is a he. Lives in NJ.   I had a run in with him about 10 years ago over purchase I made on Ebay.  Same result.  Never again. 

Nelson Wood


-----Original Message-----
From: Guenther Paul <paulguenter@...>
To: SouthBendLathe <SouthBendLathe@groups.io>
Sent: Thu, Sep 26, 2019 1:51 pm
Subject: Re: [SouthBendLathe] Dial Indicator Holder for 9/10k Lathe

Sam
Its gigigirl111 she wants $ 359.99 that's crazy 

GP


On Thursday, September 26, 2019, 01:09:21 PM EDT, Sam <i.am.sam.sam.i.am2008@...> wrote:


Which seller ?
That way we can block


On Thu, Sep 26, 2019 at 11:21 AM William Nelson <wnnelson@...> wrote:
I bought 2 items from this seller. The first was a bunch of reamers which were fine and the shipping was ok because they were heavy. The second was a lot of new carbide endmills which weren't new. They had chips in the flutes. When I complained the responce from her ( or him) was that a machinist said they were new. It wasn't worth the hassle of sending them back on my dime. Her shipping is a joke. She says flat rate shipping for almost everything but sends it in a small plastic bag instead. Claims to give shipping rebates but that's a lie. Bottom line I wont ever buy from that one again.

Re: Dial Indicator Holder for 9/10k Lathe

Nfwood
 

She is a he. Lives in NJ.   I had a run in with him about 10 years ago over purchase I made on Ebay.  Same result.  Never again. 

Nelson Wood


-----Original Message-----
From: Guenther Paul <paulguenter@...>
To: SouthBendLathe <SouthBendLathe@groups.io>
Sent: Thu, Sep 26, 2019 1:51 pm
Subject: Re: [SouthBendLathe] Dial Indicator Holder for 9/10k Lathe

Sam
Its gigigirl111 she wants $ 359.99 that's crazy 

GP


On Thursday, September 26, 2019, 01:09:21 PM EDT, Sam <i.am.sam.sam.i.am2008@...> wrote:


Which seller ?
That way we can block


On Thu, Sep 26, 2019 at 11:21 AM William Nelson <wnnelson@...> wrote:
I bought 2 items from this seller. The first was a bunch of reamers which were fine and the shipping was ok because they were heavy. The second was a lot of new carbide endmills which weren't new. They had chips in the flutes. When I complained the responce from her ( or him) was that a machinist said they were new. It wasn't worth the hassle of sending them back on my dime. Her shipping is a joke. She says flat rate shipping for almost everything but sends it in a small plastic bag instead. Claims to give shipping rebates but that's a lie. Bottom line I wont ever buy from that one again.