Hi, I use N.I.N.A as sequencer. When connecting to sitechExe V0.95Z I get a warning: "The clock of the mount differs from the clock of the computer by 7200sec.Please refer to the documentation of the

Hi, I have been using Sitech Servo1's on two scopes for over 10 years...It is capable of far more than I use it for. Recently my old and slow XT based observatory based computer forced me to move to a

Hi. For some obscure reason, my telescope doesn't want to track right. The target slowly drifts off center even tho I think I have all the settings correct, my polar alignment was correct. I have 715

Hello folks, I see that in the time server thread that someone has set the system so that NINA is connected to the mount. How is this done? Chris

For years we have been using a 150mm Renishaw RESA ring with a Renishaw Resolute readhead on the RA axis without any difficulties. We have adapted the DEC axis on our split ring mount using two pulley

Hello. Im just wondering how to perfect my polar alignment using the platesolve feature. After I do a 3 point model, the features tab says Im off polar alignment. What do I do then? Do I move the scop

Hello all, After sitting unused for 3 months (roll-off motor broke followed by unusually persistent monsoon season), my Sitech Servo I Controller does not wake up. Neither the computer nor its setting

Dear all, I've installed all motors (Faulhaber) and Sitech II on my aluminium 30", and have all running. Two things that are special: Noise. As my telescope is made of aluminium, motor noise is quit s

Hello. I having some problems with the pointing accuracy and tracking of my telescope. It was relatively poorly polar aligned because it’s very hard to do with a scope like this. After I initialised t

Dear all, After a long trip with my 30" with Servo Controller II and radio handpad to the south of France, starting up the Servo Controller, the radio handpad does not work anymore. LEDs on the receiv

Hi! My telescope seems to track extremely poorly and I would like to start guiding. Is there a way to connect PHD2 guiding to SiTech, to assist the telescope with tracking? Do you perhaps have any rea

I just received a Bluetooth-Serial Adapter (BSA) and attempted to get it working..... I plugged it into the Controller I and powered up the system. the red light on the serial adapter started flashing

that should have been called the ServoConfig.cfg.... If I place long/lat in the ServoConfig.cfg file in the ServoConfig folder, will the two apps pick it up? I was thinking about using a GPS dongle an

Hello all, I am having a hard time figuring this out. My encoder on the R,A. Axis is not showing any movement. I have tried 3 motors (motors worked) and encoders(encoders did not) and continuity teste

Hello! I was wondering if, after playesolving with the SiTechZWO program I can use outside software like Sharpcap to do imaging and or EAA?

For those that couldn't see Joe's photos of the workshop in the body of the previous email I sent, they are now attached to this email. Howard

Hi Drew and Chuck, Be sure and visit me in Payson, AZ, along the way. We can visit the nearby 4.3m Lowell Discovery Telescope and also Lowell Observatory. I'm teaching astronomy research at Payson Com

Hi everyone, Below are a series of photos taken by Joe LaCour at the Alt-Az Workshop this past weekend - enjoy! Howard Joe LaCour KineOptics 3716 Sequim Dungeness Way Sequim, WA 98382 360-775-6974 Opt

Hi everyone, Zane was kind enough to split out the individual presentations from the YouTube live streams, making it much easier to view each presentation. Thank you Zane! These videos can be seen her

Hi again, Below are the YouTube live stream links for each session. October 8, 2022 morning session https://youtu.be/AOGI5IAEc5c October 8, 2022 afternoon session https://youtu.be/OQdNMQXFt-o October