I doubt that anyone has done this. It would require careful "hacking" the board and installing some kind of buffer/switch circuit. Schematics are not published for the RSP1a so it would require a lot

#RSP1andRSP1a

My apologies Jean-Louis, by clunky I mean it is a large GUI for such a menial task and is not easily manageable for multi-recordings.

#RSP1andRSP1a #SDRuno #Plugins

The RSP1A is excellent value for money. The RSP1a and the RSPdx have similar performance above 2 MHz. The RSPdx has a special mode called HDR for better performance below 2 MHz. It gives more dynamic

#RSP1andRSP1a #Computer

I don't have much confidence in the accuracy of signal levels displayed by the IC-7300 however I know the RSP1A/Uno signal level reading is more than adequate for home use and also for some profession

#RSP1andRSP1a

Hello These days i was testing with a handmade clone of the yoloop antenna design that seems not to be so well working for unknown reasons . This si the antenna in which you invert the middle point by

#RSP1andRSP1a

Thank you to everyone that provided comments. I have been using my IC-7300 and PTRX for several months with no issues. I operated last weekend participating in the Winter Field Day contest when I firs

#HDSDR #SDRPlay #SDRuno #RSP1andRSP1a

Hello, Just looked at the virtualhere video, a great and nice solution But they also mention about a client server version of SDR Uno Is there any information about this client server version And posi

#RSP1andRSP1a #SDRuno

Before going nuclear, make absolutely sure you have completely uninstalled any erroneous device drives in Device Manager: View / Show hidden Devices Then make sure you have the manufacturer’s (not Mic

#RSP1andRSP1a

I will try that.

#RSP1andRSP1a

Uno Main - SETT - Offset - None Uno should display same frequency as your rig? Steve Brightman - On the go! Please forgive iTypos etc!

#RSP1andRSP1a

Hi Steve and Preston, Normally I can get these things to work, but this one I had. That video may help Preston and I appreciate it. I did refer to that video. I think my issues might lie with the oper

#SDRuno #RSP1andRSP1a

Thanks - that fixed it. The section on page 24 of the V1.41 manual "VFO (Hz): Displays the VFO assigned to the scheduled event. Note: if a profile is used, this VFO frequency overrides the VFO frequen

#RSP1andRSP1a #SDRuno

Thanks Steve and Ming, I like the performance on the Mac mini with M1 chip. I guess I will just have to make adjustments for SDRUno and my SDRPlay. Les

#RSP1andRSP1a

Regarding your CLONE MSI RSP1 READ the License terms that you agreed to. They clearly state that the software should not be used with anything other than genuine SDRplay hardware. You know full well t

#RSP1andRSP1a

Ok, I'm officially a dummy. Turns out ... ________________________________________ NO WORRIES, CHARLIE ! Just use your DAILY MULLIGAN (you know, it is like getting a free drop in a friendly game of go

#SDRPlay #RSP1andRSP1a #Antennas

I would do what Sam and James suggest. Start with the cable. If you jut bump the cable, you can interrupt the connection and lose contact with the RDSP1. Either stop bumping it, or get a better grippi

#RSP1andRSP1a

Hi group, hoping to find an answer in this group. I have a second hand RSP1A and using it as a 2MHz wide VHF receiver for 2m amateur radio band in Germany. Then publishing through PA3FWMs websdr softw

#RSP1andRSP1a

Hi Dave, Would it be possible to see a Schematic for your T/R Switch. Would have sent you a Private Message but could not find your email address. Looks like a good Club Project. Best Wishes & Thanks!

#RSP1andRSP1a

Thanks Franco. Not sure how I missed the ARM 32-bit driver. That is definitely going to help. Regards

#RSP1andRSP1a #FeatureSuggestions

I had a similar issue with a USB 3 hub, and I'll detail my experience here in case it helps anyone else. I'm using an older laptop with USB 2.0 ports only, and purchased a new USB 3.0 hub (USB 2.0 hub

#RSP1andRSP1a