|
RigPi, WSJT-x and a Bitx40 - Setup screen shots (no CAT control)
#wsjt-x
I thought I would dust off my Bitx40 and connect it to the RigPi: The RigPi settings, a hard-wired PTT required: WSJT-x settings: Ta-da, a contact!
I thought I would dust off my Bitx40 and connect it to the RigPi: The RigPi settings, a hard-wired PTT required: WSJT-x settings: Ta-da, a contact!
|
By
ccoles326@...
·
|
|
RigPi and WSJT-X - Unreliable FT897 CAT with 1.05 #wsjt-x **SOLVED**
#wsjt-x
Howard, I finally cracked it! When I looked at the Hamlib error message, it was trying and failing to set split mode operation. Checking WSJT-X settings again, I noticed that Split Operation had been
Howard, I finally cracked it! When I looked at the Hamlib error message, it was trying and failing to set split mode operation. Checking WSJT-X settings again, I noticed that Split Operation had been
|
By
...
·
|
|
RigPi and WSJT-X - Unreliable FT897 CAT with 1.05 6 messages
#wsjt-x
Thanks Mike, I had checked all the digi settings on the FT857 and they were all as required. I swapped over to the W10 machine and ran WSJT-X and I get tones out and as I use VOX I had power out. Trie
Thanks Mike, I had checked all the digi settings on the FT857 and they were all as required. I swapped over to the W10 machine and ran WSJT-X and I get tones out and as I use VOX I had power out. Trie
|
By
G8HAV
·
|
|
WSJT-X with FLRIG 2 messages
#wsjt-x
#ic-7300
Hi Martin, Flrig and Hamlib are different connection programs. Flrig does not use Hamlib. To use Flrig you must disconnect your radio from RigPi and Hamlib or you will get a port conflict. —Howard
Hi Martin, Flrig and Hamlib are different connection programs. Flrig does not use Hamlib. To use Flrig you must disconnect your radio from RigPi and Hamlib or you will get a port conflict. —Howard
|
By
Howard Nurse, W6HN
·
|
|
Kenwood TS-480SAT supported? 4 messages
#cat
#fldigi
#kenwood
#remote
#wsjt-x
Sri Howard, I found TS-480 as number 228. Alf Den 8 apr. 2020 kl. 10:36, skrev Alf Blomqvist:
Sri Howard, I found TS-480 as number 228. Alf Den 8 apr. 2020 kl. 10:36, skrev Alf Blomqvist:
|
By
...
·
|
|
Homebrew CIV Interface
#rigpi
#fldigi
#wsjt-x
#icom
I've got two systems running and working very well. One supports a ICOM IC7300 (USB CI-V) and another supporting a ICOM IC706MK2G. While working out the kinks with the 7300 system, a PTT issue was fou
I've got two systems running and working very well. One supports a ICOM IC7300 (USB CI-V) and another supporting a ICOM IC706MK2G. While working out the kinks with the 7300 system, a PTT issue was fou
|
By
Andy
·
Edited
|
|
#wsjt-x 4 messages
#wsjt-x
Mine is in /home/pi/.local/share/WSJT-X Note the "." in front of local as it is a hidden directory. If you are looking in the directories via the file browser, just hit Ctrl-h to show the hidden folde
Mine is in /home/pi/.local/share/WSJT-X Note the "." in front of local as it is a hidden directory. If you are looking in the directories via the file browser, just hit Ctrl-h to show the hidden folde
|
By
...
·
Edited
|
|
No RF output with WSJT-X
#audio
#wsjt-x
This is a placeholder and searchable topic to perhaps help other folks. I was struggling trying to get the RigPi working with WSJT-X. While a Signalink would work, I couldn't get RF output via the Rig
This is a placeholder and searchable topic to perhaps help other folks. I was struggling trying to get the RigPi working with WSJT-X. While a Signalink would work, I couldn't get RF output via the Rig
|
By
...
·
Edited
|
|
#ic-7300 #wsjt-x
#ic-7300
#wsjt-x
After using the WSJTX program on the Pi with no problems a new problem got in the rig control of the IC7300. I can tab the PTT butoon on the screen and the 7300 goes to TX BUT is will not go to RX whe
After using the WSJTX program on the Pi with no problems a new problem got in the rig control of the IC7300. I can tab the PTT butoon on the screen and the 7300 goes to TX BUT is will not go to RX whe
|
By
PA3EKI
·
|
|
WSJT-X - IC-7100 USB Audio 4 messages
#wsjt-x
#icom
That worked thanks again.
That worked thanks again.
|
By
...
·
|
|
How do I set the time INACCURATELY? 4 messages
#wsjt-x
Hi Tom, The Raspberry Pi does not have a real time clock, but the time can be set manually from Terminal by using a command. Any offset sticks until you reboot when the time is updated through the Int
Hi Tom, The Raspberry Pi does not have a real time clock, but the time can be set manually from Terminal by using a command. Any offset sticks until you reboot when the time is updated through the Int
|
By
Howard Nurse, W6HN
·
|
|
How do I set the date and time accurately on the RigPi? 3 messages
#wsjt-x
Mark, Thanks! My wireless internet connection is in and out in my basement where my radios are located. Eventually, the date and time were updated after re-booting several times. Some of the software
Mark, Thanks! My wireless internet connection is in and out in my basement where my radios are located. Eventually, the date and time were updated after re-booting several times. Some of the software
|
By
William E Keicher KC1HTT
·
|
|
Has anyone built WSJT-x V2.1 for the RigPi ? 2 messages
#mfj-1234
#wsjt-x
Hi Bob, The instructions on the web site you provided are much more complicated than necessary. Since WSJT-X is already installed, all the necessary dependencies (including Hamlib) are already in RigP
Hi Bob, The instructions on the web site you provided are much more complicated than necessary. Since WSJT-X is already installed, all the necessary dependencies (including Hamlib) are already in RigP
|
By
Howard Nurse, W6HN
·
|