Don, TX audio was the last thing I got working on my RigPi/TS-2000. Was a bad solder joint on a jumper to the 13 pin Din cable. My own doing. In that troubleshooting I messed up the RX audio levels. M

#mumble

Michael, Thank you. I found the same to be true. I am using the named device now. Cheers Don KC0DE

#mumble

Howard, My early morning update....I set the Mumble Output to 175%. In Alsamixer, the playback was already set at 100%. I also increased the MIC Boost function. The result is louder audio when tested

#mumble

FYI in my work getting Mumble to work in the Mumble settings select the actual device name. I had issues using “default” even though the device was the default. Mike

#mumble

More progress... There are several places where TX AUDIO can be boosted, It might take one or more of these settings to get it right. First, check the output volume in the Mumble Audio Output settings

#mumble

Howard, Ok. Got the Mumble issue sorted out relative to saving the settings. That worked. I used the earphone side of my headset plugged into the TX OUT of the RSS. While connected via my tablet, I ca

#mumble

OK, we are going in the right direction. There is a quirk in Mumble. When you make changes, click Apply, then OK. Finally, restart Mumble. Mumble only saves changes when it is shut down manually, not

#mumble

Howard, Thanks for the quick response. Yes it has been disappointing but I am determined to get this to work. I will answer each question. Yes, I am using the new RSS, the cable supplied by MFJ and th

#mumble

Hi Don, That's disappointing, it appears we are back where we were before MFJ sent you the new RigPi. Port forwarding is not used when you are using RigPi at home on the same network. Port forwarding

#mumble

Greetings, I am back. I have fully operational RSS for control of my TS2000. I have spent the last couple of weeks (off and on) trying to get audio to work on my device. I have failed so far. I am usi

#mumble

Hello, For anyone watching this thread Al's problem is he can't get the receive audio working from his laptop. He most likely has a setting wrong in the sound-card definitions on his laptop. I am real

#ic-7300 #mfj-1234 #mumble

Bill, Thanks for mentioning that. I am sure it will help others. My radio came with the latest software so you are correct. Harold

#ic-7300 #mfj-1234 #mumble

Harold, I followed the instructions concerning loading the july 11.dat file, but I encountered an error message "illegal data" generated by my ICOM 7300 when I tried to load the file. I think the prob

#ic-7300 #mfj-1234 #mumble

Thanks Mike for the reply. I down loaded the .dat file as advised by Harold, and i was trying to load those setting on the IC 7300, thats when i get the error message with " illegal data " flashing on

#ic-7300 #mfj-1234 #mumble

Thanks Will try that and report Regards Jith

#ic-7300 #mfj-1234 #mumble

Thanks Harold I did format the SD card on the radio prior to copying the July11.dat file. I first backed up the radio on a SD card, and then used another SD card to copy the .dat file. Jith

#ic-7300 #mfj-1234 #mumble

Jith Vu2oy When you say you have downloaded and have an error on update, please tell me where you see the error. The download should be applied to the RigPI. It was unclear if you were updating the Ri

#ic-7300 #mfj-1234 #mumble

Jith, If you can't get my file to load you can enter all the settings manually. Here is a link to a document that Clint put together and it has all the radio settings for the 7300 and the 7100. https:

#ic-7300 #mfj-1234 #mumble

Jith, That's a new one on me. As long as you create a backup on your radio first and then copy the file to the correct directory it should work fine. Format the SD card in the radio before you do the

#ic-7300 #mfj-1234 #mumble

Hello Harold Thanks very much for the advise I downloaded the dat file form the link provided. When i tried to load the settings from the SD card, i am denied a copy, and what i see is " illegal data

#ic-7300 #mfj-1234 #mumble