Bill, I have bren experimenting with the IC-705 using the 7300 profile in the drop down list, (I also have a 7300) and yes, just put A4 for CI-V address and most things work, I have some custom macros

#ic-7300 #ic-705

I am having an issue connecting to my IC 7300 to operate in SSB. everything is working for operating FT8 using WSJTX. The radio won't connect and when I get it to connect the I can not get the PTT to

#ic-7300

That’s a fault of the Raspberry Pi/SD card combination, not the RigPi firmware. SD cards were not designed to be used as OS disk drive replacements with lots of read/write access. They were intend as

#ic-7300

Hi Garry, Any radio that provides audio through the USB CAT cable (via internal CODECs) does not require the audio board. RigPi supports CW via CAT, although using a Keyer board is more versatile. Rem

#ic-7100 #ic-7300

Hi Lucas, 1.) have you opened Mumble’s port address on your router (port forewarning)? You should open your router external port 64738 and tie that port to your RigPi’s IP address. Save the changes. 2

#ic-7300 #vnc #commands

I have an Icom 7300 with the RigPi. Set up on lan network for now. I have all audio working. When I use the PTT on the remote connection; I get modulation on radio for about 15 seconds then the modula

#ic-7300

Wondering if there is a solution to remove white noise from RigPi / Mumble Audio. With IC-7300 into a dummy load (no signals present) significant amount of white noise at the remote end using Macbook

#ic-7300

It’s physically connected via USB and then made available to the network by running the RSP TCP server. It’s available from the SDRPlay website. See the link below for documentation. https://www.sdrpl

#rsp1 #rigpi #ic-7300 #panadapter #sdruno

THESE WORK ON MY IC-7610. HOPE THEY WORK ON OTHER ICOMS TOO. For adjusting the brightness levels of the rigs waterfall without lowering/raising the signal: REFERENCE LEVEL -0 db *1w \0xFE\0xFE\0x98\0x

#ic-7300 #ic-7610

Hi Paul Is mumble on your pc connecting OK? 73 Glenn VE9GJ

#ic-7300 #audio

I have last days working with the RIGPI I cannot fix the problem , withe the internal soundboard. Nothing Audio out from the internal soundboard. I have open the case and see that on the small Audio b

#ic-7300

OK. somehow I've managed to solve the issue and it is working fine from the iPad. thanks radiorusso for the tip!

#ic-7300 #mumble

Hello Andy, I'm having the same issue with the PTT and cannot TX audio either, did you find the issue? thanks fer

#ic-7300

Thank you very much for the info, Howard. Also, thanks for RigPi. I'm having entirely too much fun working HF from my phone at work!

#ic-7300

-Hi Howard , step 2 is successfull , the check wasn't here ! All is ok ! Many thanks for your support ! When new version for the station server will be done ? now is 1.05. Best 73's QRO from Paris !

#ic-7300

Got it, thanks. I'll give it a try.

#ic-7300

Make sure PTT in Plumble is set to Continuous.

#ic-7300

Hi Martin, Flrig and Hamlib are different connection programs. Flrig does not use Hamlib. To use Flrig you must disconnect your radio from RigPi and Hamlib or you will get a port conflict. —Howard

#wsjt-x #ic-7300

Understood, John. Sound cards connected to a RigPi USB ports will appear as available audio connections. Since RigPi supports external Winkeyers, your Modem keyers should work. This assumes all output

#ic-7300 #ic-7100 #icom #multiple

Hi Howard Thank you for taking time reply and thank you for your great work on Rigpi. I have been searching google for a while, without finding any obvious solution, but I am sure somebody out there,

#rigpi #ic-7300