Why not share to the list? Or post onto the groups page? Seems odd... Thanks 73 Jim W7RY On 1/3/2021 10:45 AM, radiorusso wrote:

#ftdx3000

Mark contact me off the list I have Rigπ setup on 3 FTdx 3000's 1 for me and 2 others for Hams operating remotely from Florida I also have an extensive list of macros that allow operation of all the f

#ftdx3000

Hi Mark. Look for the TS590s video in the Files section. Regards from Loic, SM5VFE

#ftdx3000

Has anyone put together the steps and settings yet for an FTDX3000? I have seen a lot of tidbits of information, but I do not seem to find anything that would help someone start from the beginning to

#ftdx3000

When I key PTT the RigPi outputs noise to the radio. (If I pull the plug on TX Out there is no noise on PTT). The TX Out cable goes to line in at the back panel of the FTDX3000. The rig microphone is

#ftdx3000 #rigpi

Yes, I think it started after I updated Hamlib. I've re-flashed the image for that RigPi, and am leaving Hamlib alone. Chris

#ftdx3000 #cat #yaesu

Pi-Hole blacklisted site... Perry K4PWO

#ftdx3000 #cat #yaesu

I was wrong it was Banggood https://tinyurl.com/y4jjt43q 73 Glenn VE9GJ

#ftdx3000 #cat #yaesu

I will check the details when I get home. Was either enay or amazon. Glenn VE9GJ

#ftdx3000 #cat #yaesu

Hi glen YES it does the same thing with the usb 2 ports. . It disconnects mumble I think when there is a noise burst. What bran isolator do you use ? Tnx Russ W4PGT

#ftdx3000 #cat #yaesu

Hi Chris Looks like your radio is fine, good news You mentioned you upgraded hamlib, did the problems start after that? Try the Test radio button and when it fails copy the rigctl info and try it in a

#ftdx3000 #cat #yaesu

Hi Russ Did you have the isolater plugged into a black or blue USB port on the pi4? I use isolators on my pi4 but always use thw black ports. The blue are USB3 and the isolaters are ususally USB2 at b

#ftdx3000 #cat #yaesu

I connected the Yaesu FTDX 3000 to the RP3 based MFJ-1234 RigPi, and the RigPi1 software saw the radio immediately, and successfully connected to it. I'm guessing that my updating of HamLib somehow ho

#ftdx3000 #cat #yaesu

Chris I had the USB port on my FT 3000 die last February while working with RIGpi Yaesu replaced the board under warranty even though I had the radio 15 months. Bought a USB Isolator to protect the US

#ftdx3000 #cat #yaesu

I very much like the changes made for RigPi2. Chris

#ftdx3000 #cat #yaesu

Oh, another change I did was I updated Hamlib, according to the instructions in 6.2: 6.2 Installing the latest Hamlib The Hamlib control library is constantly updated by the maintenance team. Hamlib m

#ftdx3000 #cat #yaesu

I'm having intermittent connection success with my Raspberry Pi 4 (8 GB), RigPi 2, and Yaesu FTDX 3000. I've tried changing USB cables, and that did not help. When I first installed the new RigPi2 ima

#ftdx3000 #cat #yaesu

I was able to figure it out by looking at other posts. The macro is *0w \0x41\0x43\0x30\0x30\0x32\0x3b

#ftdx3000 #rss #commands

I am needing help in what macros to use in the RSS to utilize the internal tuner of the FTDX 3000 radio.

#ftdx3000 #rss #commands

Today, when I fired up RigPi, and told it to connect to my radio, FT DX 3000, it immediately goes into transmit again. Somehow, the /dev/radio1 is messed up today, and is pointing at USB1 instead of U

#ftdx3000