Date   

Re: Rigpi with IC-718

Adam Hosa
 

There’s 9600 and ‘hi’ in the civ baud selection. Trying hi, even though I can’t find any documentation on what hi is haha


Re: CGNAT

clint parreno <sv_clintrace999@...>
 

Will the rigpi requires a dynamic / static IP? Our ISP in the philippines is under CGNAT where a 1 public ip were shared by many users, i don't think port forwarding is an issue though.

Thanks

Clint


On Sat, May 18, 2019 at 4:28 AM, Howard Nurse, W6HN
<hlnurse@...> wrote:
Hi Clint,

There is no simple way to set up port forwarding through CGNAT, but it is possible.  Use Google to search for ngrok for Linux.  I have not had experience with solving the CGNAT issue, but some googling came up with this possibility.

73, Howard W6HN


TS 590 Audio TX/RX

Doug Rea
 

Good Morning All!

Anyone try this device on a TS-590sg yet? 
Just got mine yesterday from HRO for the purpose of replacing Remotehams.
USB connections seem solid and is allowing me to control the rig just fine but the 13pin din to RJ45 connection is not giving any audio.
I think my audio setting on the 590 are correct but I am wide open to check again.

Advice?

Doug Rea
kx4ib


                              


Re: Receivers and AM

Michael Young
 

The FRG-100 is on the list.

Isn’t the IC-A24 an aircraft band hand held?  It’s not on the list.  

IC-2725 not on the list.  I looked at the manual and got the impression it’s not fully CAT controllable.   Limited to memory programming.  But I also cud b wrong.  

Mike
WB8CXO

On May 19, 2019, at 5:21 AM, Michael Young via Groups.Io <wb8cxo@...> wrote:

RigPi uses the Hamlib library for radio support.   Here’s a link to check out:


Hopefully your radios listed.

Mike
WB8CXO


On May 19, 2019, at 5:00 AM, Info@... wrote:

The receivers in question are..
Yaesu frg-100 receiver
Icom ic-2725 transceiver
Icom ic-A24 transceiver


All on AM mode


Re: Rigpi with IC-718

Howard Nurse, W6HN
 

Hi Adam,

(Thanks, Mike, for your help with the 718.)

Here is additional info:

1. The IC-718 Baud rate can be set using the menu selection for AutoBaud.  Default is “At” which is automatic.  Other fixed values can be found in the AutoBaud list.  Select the highest Baud rate in that list.  This is what Hamlib uses for their default.

2. The menu selection CI-V Transceive (which sends unsolicited data from the radio), must be OFF or RSS will get confused.

3. In other messages we have described how to use the Raspberry Pi Terminal to bypass RigPi.  You’ve done that, but try again after making the changes in 1 and 2.  If you get a prompt “Command:” you are good.  Type an F followed by a return to read the radio’s frequency.  If you see the frequency you can start celebrating.

4. Use Ctrl+C to exit the rigctl program.  Open a RigPi browser and go to Advanced Radio settings.  Make all boxes say Default.  Try Connect Radio.  If it fails, use Disconnect Radio, then try the Test button.  As Mike said, the images you sent need to be higher resolution so we can read them.

There is a possibility the cable you are using for CI-V to USB is not correct, or may be bad...

We WILL get you going!

73, Howard W6HN


Re: Receivers and AM

Michael Young
 

RigPi uses the Hamlib library for radio support.   Here’s a link to check out:


Hopefully your radios listed.

Mike
WB8CXO


On May 19, 2019, at 5:00 AM, Info@... wrote:

The receivers in question are..
Yaesu frg-100 receiver
Icom ic-2725 transceiver
Icom ic-A24 transceiver


All on AM mode


Re: Rigpi with IC-718

Michael Young
 

I’ve not used CI-V on an IC-718 myself so we’re both learning until someone else who has jumps in to help!

To learn more about it refer to the 718’s user manual and Hamlib.   User manual is easy so that’s what I looked at first.  I even looked at a couple you tube videos to see how it works.   I could not find in the manual exactly what RANGE of BAUD RATES the 718 supports but I did see an AUTO selection.   AUTO would be one thing to try but I just looked at Hamlib docs and they indicate max baud rate is 19,200, 8n1 BUT the 718 manual doesn’t specifically indicate how to to change baud rate to a specific speed.  Having a 718 to play with would possibly expose that unknown.   But I would try CI-V to AUTO on the 718... or if you can figure out with the radio how to set a specific speed to 19,200, do that. Set/verify the CI-V address to 5E, (the default), CI-V transceive to on (the default), CI-V 731 mode to off (the default).   For RigPi Settings>Radio>Basic>Manu Icom, model IC-718, port /dev/tty/USB0. Everything else to default.  Settings>Radio>Advanced use all the default settings for now.  Click test radio, see what happens.  I’m doing this from memory with no support hardware (RigPi) in front of me.  4 hours of HamVention left!

Can be easy, can be difficult...

Hopefully someone who has done this will jump in and help us...

73
Mike
WB8CXO

On May 18, 2019, at 7:45 PM, Adam Hosa via Groups.Io <Ifone@...> wrote:

So far no luck. If i try running some commands from the pi terminal (using 313 which is for a 718) Im getting a communication bus error. Saw some posts somewhere about having to turn off CI-V transceive on icom radios (which I did). Dont know if i need to maybe specifically set baud rate on the 718 and rigpi? Tinkering around with it. I had several cables laying around which i thought should work for CIV (have the USB end with that 'converter) and 1/8 " on the other for the rig. Enjoying myself, hasnt exactly been plug-n-play yet, but somehow i'll figure it out  :)


Re: Receivers and AM

info
 

The receivers in question are..
Yaesu frg-100 receiver
Icom ic-2725 transceiver
Icom ic-A24 transceiver


All on AM mode


New file uploaded to RigPi@groups.io

RigPi@groups.io Notification <RigPi+notification@...>
 

Hello,

This email message is a notification to let you know that a file has been uploaded to the Files area of the RigPi@groups.io group.

File: RigPi-CAT Connection-v0.81.pdf

Uploaded By: WA8KHP -

Description:
Flow chart diagrams for making decision on connecting the RigPi to a PC and/or amateur radio transceivers for CAT CONTROL.

You can access this file at the URL:
https://groups.io/g/RigPi/files/CAT%20Control%20Logic/RigPi-CAT%20Connection-v0.81.pdf

Cheers,
The Groups.io Team


New file uploaded to RigPi@groups.io

RigPi@groups.io Notification <RigPi+notification@...>
 

Hello,

This email message is a notification to let you know that a file has been uploaded to the Files area of the RigPi@groups.io group.

File: RigPi-CAT Connection-v0.81.pdf

Uploaded By: WA8KHP -

Description:
Flow chart diagrams for making decision on connecting the RigPi to a PC and/or amateur radio transceivers for CAT CONTROL.

You can access this file at the URL:
https://groups.io/g/RigPi/files/RigPi-CAT%20Connection-v0.81.pdf

Cheers,
The Groups.io Team


Re: Receivers and AM

Mark Weisheimer
 

The list of know radios supported by HamLib is here:
https://groups.io/g/RigPi/files/RigPi%20Documentation/Hamlib%20Radio%20List%205-7-19.pdf
If the receiver can be controlled via CAT commands, and recognizes the commands of another radio listed, then it should work.
Audio from most any radio or audio source can be carried remotely via Ethernet or WiFi by RigPi using the Mumble VOIP server.

73 - Mark - K8MHW


Re: Patch rig 1 to rig 2?

Mark Weisheimer
 

Hi Steve,

I think that you are looking for a repeater controller.
The RigPi is meant to control a CAT capable radio and make an audio connection using a network connection and does not support those roles using only an RF link.

73 - Mark - K8MHW


New file uploaded to RigPi@groups.io

RigPi@groups.io Notification <RigPi+notification@...>
 

Hello,

This email message is a notification to let you know that a file has been uploaded to the Files area of the RigPi@groups.io group.

File: RigPi Intro - Quick Start Guide.pdf

Uploaded By: WA8KHP -

Description:
This document is included with your purchase of a RigPi MFJ-1234.

You can access this file at the URL:
https://groups.io/g/RigPi/files/MFJ%20RigPi%20Station%20Server%20Quick%20Start/RigPi%20Intro%20-%20%20Quick%20Start%20Guide.pdf

Cheers,
The Groups.io Team


Re: Receivers and AM

Tom W5KUB <Tom@...>
 

if your radio will do AM then yes.  The rigpi will allow you to select ssb, fm, am, etc. 


Host of live ham show called Amateur Radio Roundtable every Tues night at 8:00 PM central. All shows are recorded and can be watched at any time on on our website. Our audio is also simulcast on international shortwave on 5130 Khz.   We are also on every podcast carrier if you are looking for an audio version of our program.


On Sat, May 18, 2019 at 4:52 PM <Info@...> wrote:
Does anyone know if receivers are supported and am mode ?


Re: Rigpi with IC-718

Adam Hosa
 

So far no luck. If i try running some commands from the pi terminal (using 313 which is for a 718) Im getting a communication bus error. Saw some posts somewhere about having to turn off CI-V transceive on icom radios (which I did). Dont know if i need to maybe specifically set baud rate on the 718 and rigpi? Tinkering around with it. I had several cables laying around which i thought should work for CIV (have the USB end with that 'converter) and 1/8 " on the other for the rig. Enjoying myself, hasnt exactly been plug-n-play yet, but somehow i'll figure it out  :)


Re: Receivers and AM

WA8KHP -
 

Does that RX support CAT Control via serial or USB connection?  The Mode makes no difference.

73

David - WA8KHP

On May 18, 2019, at 4:52 PM, info@... wrote:
Does anyone know if receivers are supported and am mode ?


Re: Receivers and AM

Michael Young
 

RigPi supports the modes the radio connected to supports for the most part.  

On May 18, 2019, at 2:12 PM, Info@... wrote:

Does anyone know if receivers are supported and am mode ?


Receivers and AM

info
 

Does anyone know if receivers are supported and am mode ?


Re: Rigpi with IC-718

Michael Young
 

Hi Adam,

At Hamvention but will try to help.  Also your screenshots get blurry when I zoom in with smartphone.

Goto Settings>System>there’s a button to power down the Pi.  Click it to gracefully power down the Pi. Then cycle the power to power/boot up.  

make sure the 718 is set to the highest baudrate it will support.  

Plugin the 718 to a RigPi USB port using the appropriate cable.

Goto Settings>Radio>Basic and set Manu to Icom, Model to IC-718,Port to dev/ttyUSB0.  Click the cloud to save settings.  

Then goto Settings>Radio>Advanced and click Test Radio.  Hopefully at the bottom of the output rigctl will show a connect.  If successful the tuner page will show the frequency and mode the 718 is tuned to and you should be able to control the radio.  

Sorry if I missed something. Doing this from (old) memory.  

Good Luck

Mike
WB8CXO



On May 18, 2019, at 12:04 PM, Adam Hosa via Groups.Io <Ifone@...> wrote:

<0C87905C-5276-4823-A431-7A64315288A4.png>

Here’s where I’m at...
Adam


Re: Running the tuner browser page directly on the RigPi server

Michael Young
 

Hi Manuel,  if you plug in a hmdi screen into your RigPi also a keyboard and mouse (usb wireless works great)...  When you boot the RigPi it wIll boot to the Pixel dashboard.  Clicking the pi symbol will connect you to the RSS tuner page. 

Hope this helps!

Mike
WB8CXO

On May 18, 2019, at 12:25 PM, Manuel Maseda <mmaseda@...> wrote:

Is it possible to use the tuner browser page directly on the RigPi server and operate a radio?  If so, how do you hear audio from the radio and connect a microphone?  Also the RigPi came with a single 3.5mm audio cable.  What is that for?

Manuel W4SSB

7941 - 7960 of 8159