Topics

pi9k6 Winlink Pat ARDOP


Bill AA6BD
 

Thanks, John.  The ! worked.

--
Bill AA6BD


John Wiseman
 

This is probable because you are connecting to your own call. BPQ will normally ignore the port in a connect command if the station you are calling is one of your applications or a station in your Nodes list. It connects you to AA6BD-10, your RMS application.

You can override this by prepending an ! to the call, eg

"telnet://{mycall}:CMSTelnet$2$!AA6BD-10@....0.1:8772/wl2k"

This won't be needed if connecting to a remote station.

You can confirm that the system is interpreting the password string correctly in your Telnet Server log You should see something like this

03/06/2020 07:33:23 1 127.0.0.1 Incoming Connect on Port 8772
03/06/2020 07:33:27 1 127.0.0.1 User=G8BPQ
03/06/2020 07:33:38 1 127.0.0.1 Password=CMSTelnet$9$G8BPQ-2
03/06/2020 07:33:38 1 127.0.0.1 Gateway Connect Call=G8BPQ Command=C 9 G8BPQ-2

73,
John



On 02/06/2020 22:45, Bill AA6BD wrote:
John,
Thanks for your patience with me as I work through getting this working so I can use PAT with linbpq as its ax.25 transport to my radio.

I changed the Telnet server configuration to include setting RELAYAPPL as follows:

; Basic Webmail configuration
 
SIMPLE ; This set a whole load of paramters to reasonable defaults
 
LOCATOR=CM88PL ; Set to your Grid Square to send reports to the BPQ32 Node Map system
NODECALL=AA6BD-2
 
INFOMSG:
AA6BD's LinBPQ Gateway
***
 
PORT
 ID=Telnet Server
 DRIVER=TELNET
 CONFIG
 LOGGING=1
 CMS=1 ; Enable CMS Gateway
 HTTPPORT=8080 ; Port used for Web Management/WebMail
 TCPPORT=8010 ; Port for Telnet Access
 FBBPORT=8011 ; Not required, but allows monitoring using BPQTermTCP
 MAXSESSIONS=10
 CloseOnDisconnect=1 ; Close Telnet Session when Node disconnects
 USER=aa6bd,{password},AA6BD,"",SYSOP
 RELAYAPPL=BBS
 
 ENDPORT
 
 ; Add Radio Port(s) Here
 
PORT
 ID=1200 Baud 144.xxx
 TYPE=ASYNC
 PROTOCOL=KISS
 CHANNEL=A
 COMPORT=/dev/ttyUSB0
 SPEED=19200 ; Change as required
 MAXFRAME=4
 FRACK=8000
 RESPTIME=1500
 RETRIES=10
 PACLEN=120
 TXDELAY=300
 SLOTTIME=100
 PERSIST=64
 
 WL2KREPORT PUBLIC, www.winlink.org, 8778, AA6BD-10, CM86PL, 00-23, 144960000, PKT1200, 10, 20, 5, 0
 
ENDPORT
 
APPLICATION 1,BBS,,AA6BD
APPLICATION 2,RMS,C 1 CMS,AA6BD-10
 
LINMAIL ; Enable BBS
 
Then I changed the PAT config.json connect_alias to use $2 which should point to using the ASYNC TNC port.

  "connect_aliases": {

When I use BPQ Webmail, all works as I would suspect.  I create an email which is forwarded through my ASYNC port and my radio.  And I set up forwarding on RMS to connect every 600 seconds to check for email which it does nicely.

But when I use PAT and select the connect_alias of "mytelnet," BPQ sends the email through telnet port 1 rather than through radio port 2, even though "mytelnet" is configured with $2 which should select port 2, right?  How do I get BPQ to select port 2?

The CMSAccess.log is:

20:48:04 10 AA6BD Connected to CMS
20:48:05 10 Callsign :
20:48:05 10 AA6BD
20:48:05 10 Password :
20:48:05 10 CMSTELNET
 
20:48:05 10 [WL2K-5.0-B2FWIHJM$]<cr>
20:48:05 10 ;PQ: 28364100<cr>
20:48:05 10 CMS><cr>
20:48:06 10 ;FW: AA6BD<cr>
20:48:06 10 [Pat-0.9.0-B2FHMG$]<cr>
20:48:06 10 ;PR: 35315818<cr>
20:48:06 10 ; WL2K DE AA6BD (CM88pl)<cr>
20:48:06 10 FC EM ITB2X6NKNNKF 255 220 0<cr>
20:48:06 10 F> 73<cr>
20:48:06 10 FS Y<cr>
20:48:06 10 test new pat under linbpq
20:48:07 10 FF<cr>
20:48:08 10 Disconnected. Bytes Sent = 361 Bytes Received 48 Time 4 Seconds

Am I running into some problem because both BPQ webmail and PAT mail are active at the same time?  Something else?
--
Bill AA6BD


Bill AA6BD
 

Correction, when I post the connect_aliases, this system changes the values.  

  "connect_aliases": {
    "telnet": "telnet://{mycall}:CMSTelnet@...:8772/wl2k",
    "mytelnet": "telnet://{mycall}:CMSTelnet$2$AA6BD-10@....0.1:8772/wl2k",

The values after the @ are
cms.winlink.org
and 
127.0.0.1
--
Bill AA6BD


Bill AA6BD
 

John,
Thanks for your patience with me as I work through getting this working so I can use PAT with linbpq as its ax.25 transport to my radio.

I changed the Telnet server configuration to include setting RELAYAPPL as follows:

; Basic Webmail configuration
 
SIMPLE ; This set a whole load of paramters to reasonable defaults
 
LOCATOR=CM88PL ; Set to your Grid Square to send reports to the BPQ32 Node Map system
NODECALL=AA6BD-2
 
INFOMSG:
AA6BD's LinBPQ Gateway
***
 
PORT
 ID=Telnet Server
 DRIVER=TELNET
 CONFIG
 LOGGING=1
 CMS=1 ; Enable CMS Gateway
 HTTPPORT=8080 ; Port used for Web Management/WebMail
 TCPPORT=8010 ; Port for Telnet Access
 FBBPORT=8011 ; Not required, but allows monitoring using BPQTermTCP
 MAXSESSIONS=10
 CloseOnDisconnect=1 ; Close Telnet Session when Node disconnects
 USER=aa6bd,{password},AA6BD,"",SYSOP
 RELAYAPPL=BBS
 
 ENDPORT
 
 ; Add Radio Port(s) Here
 
PORT
 ID=1200 Baud 144.xxx
 TYPE=ASYNC
 PROTOCOL=KISS
 CHANNEL=A
 COMPORT=/dev/ttyUSB0
 SPEED=19200 ; Change as required
 MAXFRAME=4
 FRACK=8000
 RESPTIME=1500
 RETRIES=10
 PACLEN=120
 TXDELAY=300
 SLOTTIME=100
 PERSIST=64
 
 WL2KREPORT PUBLIC, www.winlink.org, 8778, AA6BD-10, CM86PL, 00-23, 144960000, PKT1200, 10, 20, 5, 0
 
ENDPORT
 
APPLICATION 1,BBS,,AA6BD
APPLICATION 2,RMS,C 1 CMS,AA6BD-10
 
LINMAIL ; Enable BBS
 
Then I changed the PAT config.json connect_alias to use $2 which should point to using the ASYNC TNC port.

  "connect_aliases": {
    "telnet": "telnet://{mycall}:CMSTelnet@...:8772/wl2k",
    "mytelnet": "telnet://{mycall}:CMSTelnet$2$AA6BD-10@....0.1:8772/wl2k",

When I use BPQ Webmail, all works as I would suspect.  I create an email which is forwarded through my ASYNC port and my radio.  And I set up forwarding on RMS to connect every 600 seconds to check for email which it does nicely.

But when I use PAT and select the connect_alias of "mytelnet," BPQ sends the email through telnet port 1 rather than through radio port 2, even though "mytelnet" is configured with $2 which should select port 2, right?  How do I get BPQ to select port 2?

The CMSAccess.log is:

20:48:04 10 AA6BD Connected to CMS
20:48:05 10 Callsign :
20:48:05 10 AA6BD
20:48:05 10 Password :
20:48:05 10 CMSTELNET
 
20:48:05 10 [WL2K-5.0-B2FWIHJM$]<cr>
20:48:05 10 ;PQ: 28364100<cr>
20:48:05 10 CMS><cr>
20:48:06 10 ;FW: AA6BD<cr>
20:48:06 10 [Pat-0.9.0-B2FHMG$]<cr>
20:48:06 10 ;PR: 35315818<cr>
20:48:06 10 ; WL2K DE AA6BD (CM88pl)<cr>
20:48:06 10 FC EM ITB2X6NKNNKF 255 220 0<cr>
20:48:06 10 F> 73<cr>
20:48:06 10 FS Y<cr>
20:48:06 10 test new pat under linbpq
20:48:07 10 FF<cr>
20:48:08 10 Disconnected. Bytes Sent = 361 Bytes Received 48 Time 4 Seconds

Am I running into some problem because both BPQ webmail and PAT mail are active at the same time?  Something else?
--
Bill AA6BD


John Wiseman
 

See http://www.cantab.net/users/john.wiseman/Documents/PATSupport.html

PAT connections to or via LinBPQ use the RMS Relay emulation feature, so you need to set RELAYAPPL in the Telnet Server configuration.

The connect string embedded in the CMSPass field should include the number of the port you want to call out on. As your radio port is port 2 you need "telnet://{mycall}:CMSTelnet$2$aa6bd-10@....0.1:8772/wl2k"

73,
John G8BPQ

On 02/06/2020 01:18, Bill AA6BD wrote:
Thanks for this thread.  I was struggling to get PAT to work with ax.25 in the Linux kernel as it was timing out on large messages.  I was going to get a Signalink or equivalent and try Direwolf, but I had not discovered that PAT could work with LinBPQ until I found this thread.  This is a much better solution for me as LinBPQ has been rock solid when I use it as a Webmail client or as an RMS gateway on another Pi with TNC-Pi.

I loaded the beta of LinBPQ v 6.0.20.10 onto my Pi that also has PAT working and made it executable.
I copied linbpq.conf from my Pi that has worked as a Webmail client using a Byonics TT4 TNC.  In it, Port 01 is the Telnet port, and Port 02 is the TT4 port.
Port 01 is configured as:

PORT
 ID=Telnet Server
 DRIVER=TELNET
 CONFIG
 LOGGING=1
 CMS=1 ; Enable CMS Gateway
 HTTPPORT=8080 ; Port used for Web Management/WebMail
 TCPPORT=8010 ; Port for Telnet Access
 FBBPORT=8011 ; Not required, but allows monitoring using BPQTermTCP
 MAXSESSIONS=10
 CloseOnDisconnect=1 ; Close Telnet Session when Node disconnects
 USER=aa6bd,(password),AA6BD,"",SYSOP
 
 ENDPORT

I added a connect alias to PAT so that my aliases section of the config.json file now is

  "connect_aliases": {
    "mytelnet": "telnet://{mycall}:CMSTelnet$1$aa6bd-10@....0.1:8772/wl2k",

When I try to use BPQ32 through telnet to connect from PAT, I get:

Connecting to WL2K (telnet)...
Unable to establish connection to remote: dial tcp 127.0.0.1:8772: connect: connection refused

How should mytelnet be configured?  Or am I missing something else?

--
Bill AA6BD


Bill AA6BD
 

Thanks for this thread.  I was struggling to get PAT to work with ax.25 in the Linux kernel as it was timing out on large messages.  I was going to get a Signalink or equivalent and try Direwolf, but I had not discovered that PAT could work with LinBPQ until I found this thread.  This is a much better solution for me as LinBPQ has been rock solid when I use it as a Webmail client or as an RMS gateway on another Pi with TNC-Pi.

I loaded the beta of LinBPQ v 6.0.20.10 onto my Pi that also has PAT working and made it executable.
I copied linbpq.conf from my Pi that has worked as a Webmail client using a Byonics TT4 TNC.  In it, Port 01 is the Telnet port, and Port 02 is the TT4 port.
Port 01 is configured as:

PORT
 ID=Telnet Server
 DRIVER=TELNET
 CONFIG
 LOGGING=1
 CMS=1 ; Enable CMS Gateway
 HTTPPORT=8080 ; Port used for Web Management/WebMail
 TCPPORT=8010 ; Port for Telnet Access
 FBBPORT=8011 ; Not required, but allows monitoring using BPQTermTCP
 MAXSESSIONS=10
 CloseOnDisconnect=1 ; Close Telnet Session when Node disconnects
 USER=aa6bd,(password),AA6BD,"",SYSOP
 
 ENDPORT

I added a connect alias to PAT so that my aliases section of the config.json file now is

  "connect_aliases": {
    "telnet": "telnet://{mycall}:CMSTelnet@...:8772/wl2k",
    "mytelnet": "telnet://{mycall}:CMSTelnet$1$aa6bd-10@....0.1:8772/wl2k",

When I try to use BPQ32 through telnet to connect from PAT, I get:

Connecting to WL2K (telnet)...
Unable to establish connection to remote: dial tcp 127.0.0.1:8772: connect: connection refused

How should mytelnet be configured?  Or am I missing something else?

--
Bill AA6BD


Don
 

I know this is old, but I found the problem with this command line example:

$ pat connect telnet://k6fvc:CMSTelnet$4$k6fvc-11@...:8772/k6sdr

The dollar sign ($) is a special character to the Linux shells, so it must be escaped (with '\'):

$ pat connect telnet://k6fvc:CMSTelnet\$4\$k6fvc-11@...:8772/k6sdr

or the whole port string enclosed in single quotes.

$ pat connect 'telnet://k6fvc:CMSTelnet$4$k6fvc-11@...:8772/k6sdr'


Fred Cunha
 

I am so close… Thank You for all your assistance John!

I am using the beta 3-27 version of pilinbpq.

The radio now ‘keys-up' several times while trying to connect using Pat GUI but not with Command Line. It will however only allow one attempt, then I have to reboot to get it to retry it again. 

Pat HTTP:
2019/04/03 20:46:06 Connecting to K6SDR (telnet)...
2019/04/03 20:46:06 Connected to 127.0.0.1:8772 (tcp)
*** Failure with K6FVC-11

Telnet Log:
03/04/2019 20:46:06 1 127.0.0.1 User=K6FVC
03/04/2019 20:46:06 1 127.0.0.1 Password=CMSTelnet$4$k6fvc-11
03/04/2019 20:46:06 1 127.0.0.1 Gateway Connect Call=K6FVC Command=ATT 4 k6fvc-11

Pat GUI screen:



COMMAND LINE:
2019/04/03 20:56:29 Connecting to K6SDR (telnet)...
2019/04/03 20:56:29 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list
this is where it hangs….

Telnet Log:
03/04/2019 20:56:29 1 127.0.0.1 User=k6fvc
03/04/2019 20:56:29 1 127.0.0.1 Password=CMSTelnet-11
03/04/2019 20:56:29 1 127.0.0.1 Call Accepted Callsign =k6fvc

Command Line hang - AFTER REBOOT Telnet Log:
03/04/2019 21:01:07 1 Disconnected. Bytes Sent = 58 Bytes Received 19


On Apr 3, 2019, at 3:36 PM, Fred Cunha via Groups.Io <fvcjca@...> wrote:

Hmmm... From the last try here are the log entries... Looks like its working but reporting something else???

03/04/2019 13:03:23 1 127.0.0.1 User=k6fvc
03/04/2019 13:03:23 1 127.0.0.1 Password=CMSTelnet-11
03/04/2019 13:03:23 1 127.0.0.1 Call Accepted Callsign =k6fvc
03/04/2019 13:04:28 2 127.0.0.1 User=K6FVC
03/04/2019 13:04:28 2 127.0.0.1 Password=CMSTelnet$4$k6fvc-11
03/04/2019 13:04:28 2 127.0.0.1 Gateway Connect Call=K6FVC Command=ATT 4 k6fvc-11
03/04/2019 13:08:21 1 Disconnected. Bytes Sent = 58 Bytes Received 19
03/04/2019 13:08:22 2 Disconnected. Bytes Sent = 26 Bytes Received 27
03/04/2019 13:09:46 1 127.0.0.1 User=k6fvc
03/04/2019 13:09:46 1 127.0.0.1 Password=CMSTelnet-11
03/04/2019 13:09:46 1 127.0.0.1 Call Accepted Callsign =k6fvc
03/04/2019 13:09:52 1 Disconnected. Bytes Sent = 58 Bytes Received 19

On Wed, Apr 3, 2019 at 2:16 PM John Wiseman <john.wiseman@...> wrote:
Odd,

I copied your command onto my system, just changing the IP address to point
to my pi, and got through to the node and tried to connect.

D:\pat\pat connect telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k
2019/04/03
21:47:18 Connecting to WL2K (telnet)...
2019/04/03 21:47:18 Connected to 10.8.0.1:8772 (tcp)
POGO4:G8BPQ-9} Failure with K6FVC-11
2019/04/03 21:49:16 Got interrupt, disconnecting...
2019/04/03 21:49:16 Exchange failed: unexpected EOF

Could you send me your Telnet log (Telnet_20190403.log)?

Thanks,
John



________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of Fred Cunha
Sent: 03 April 2019 21:08
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

Using the 032719 Beta Version of pilinbpq


Command Line:
pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 13:03:23 Connecting to WL2K (telnet)...
2019/04/03 13:03:23 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


GUI:
2019/04/03 13:04:28 Connecting to WL2K (telnet)...
2019/04/03 13:04:28 Connected to 127.0.0.1:8772 (tcp)
*** Failure with K6FVC-11




On Apr 3, 2019, at 12:18 PM, Fred Cunha via Groups.Io
<fvcjca=gmail.com@groups.io> wrote:

Thank You John. 

both versions same results 


On Apr 3, 2019, at 11:58 AM, Fred Cunha via Groups.Io
<fvcjca=gmail.com@groups.io> wrote:

actually 

2019-03-27 20:08 
3.4M

On Apr 3, 2019, at 11:45 AM, Fred Cunha via Groups.Io
<fvcjca=gmail.com@groups.io> wrote:

2019-01-06 14:39 
3.3M

On Apr 3, 2019, at 8:30 AM, John Wiseman <john.wiseman@...> wrote:

Looks like the $port$call construct isn’t being recognised. What version of
LinBPQ are you running? The PAT gateway feature isn’t in the released
version, only in the beta.

73,
John

________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 03 April 2019 15:48
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

PROGRESS!

Here's the latest;

pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 07:42:42 Connecting to WL2K (telnet)...
2019/04/03 07:42:42 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


My Telnet Section of bpq32.cfg
; ********************PORT 3  TELNET **************************************
;3
PORT
 ID=Telnet Server
 DRIVER=Telnet
 CONFIG
    LOGGING=1
    DisconnectOnClose=0     ;  1 = closes window when you bye
    TCPPORT=8010
    FBBPORT=8011
    HTTPPORT=8080
    LOGINPROMPT=user:
    PASSWORDPROMPT=password:
    MAXSESSIONS=10
    RELAYAPPL=BBS
    CMS=1
    CMSCALL=K6FVC-11       ; CMS Access K6FVC (with SSID if used)
    CMSPASS=password     ; WL2K sysop password
    FALLBACKTORELAY=1    ; will try to get to RMS RELAY if CMS unavaiable
    RELAYHOST=192.168.1.21  ; put the name or ip number of your RMS_RELAY
here
    CTEXT=Welcome to K6FVC Telnet Server\n Enter ? for list of commands\n\n
    USER=k6fvc,password,K6FVC1,,SYSOP
   ; USER=username2,password2,K6FVC2,,
; add as many as you like
ENDPORT














Fred Cunha
 

Hmmm... From the last try here are the log entries... Looks like its working but reporting something else???

03/04/2019 13:03:23 1 127.0.0.1 User=k6fvc
03/04/2019 13:03:23 1 127.0.0.1 Password=CMSTelnet-11
03/04/2019 13:03:23 1 127.0.0.1 Call Accepted Callsign =k6fvc
03/04/2019 13:04:28 2 127.0.0.1 User=K6FVC
03/04/2019 13:04:28 2 127.0.0.1 Password=CMSTelnet$4$k6fvc-11
03/04/2019 13:04:28 2 127.0.0.1 Gateway Connect Call=K6FVC Command=ATT 4 k6fvc-11
03/04/2019 13:08:21 1 Disconnected. Bytes Sent = 58 Bytes Received 19
03/04/2019 13:08:22 2 Disconnected. Bytes Sent = 26 Bytes Received 27
03/04/2019 13:09:46 1 127.0.0.1 User=k6fvc
03/04/2019 13:09:46 1 127.0.0.1 Password=CMSTelnet-11
03/04/2019 13:09:46 1 127.0.0.1 Call Accepted Callsign =k6fvc
03/04/2019 13:09:52 1 Disconnected. Bytes Sent = 58 Bytes Received 19

On Wed, Apr 3, 2019 at 2:16 PM John Wiseman <john.wiseman@...> wrote:
Odd,

I copied your command onto my system, just changing the IP address to point
to my pi, and got through to the node and tried to connect.

D:\pat\pat connect telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k
2019/04/03
21:47:18 Connecting to WL2K (telnet)...
2019/04/03 21:47:18 Connected to 10.8.0.1:8772 (tcp)
POGO4:G8BPQ-9} Failure with K6FVC-11
2019/04/03 21:49:16 Got interrupt, disconnecting...
2019/04/03 21:49:16 Exchange failed: unexpected EOF

Could you send me your Telnet log (Telnet_20190403.log)?

Thanks,
John



________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of Fred Cunha
Sent: 03 April 2019 21:08
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

Using the 032719 Beta Version of pilinbpq


Command Line:
pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 13:03:23 Connecting to WL2K (telnet)...
2019/04/03 13:03:23 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


GUI:
2019/04/03 13:04:28 Connecting to WL2K (telnet)...
2019/04/03 13:04:28 Connected to 127.0.0.1:8772 (tcp)
*** Failure with K6FVC-11




On Apr 3, 2019, at 12:18 PM, Fred Cunha via Groups.Io
<fvcjca=gmail.com@groups.io> wrote:

Thank You John. 

both versions same results 


On Apr 3, 2019, at 11:58 AM, Fred Cunha via Groups.Io
<fvcjca=gmail.com@groups.io> wrote:

actually 

2019-03-27 20:08 
3.4M

On Apr 3, 2019, at 11:45 AM, Fred Cunha via Groups.Io
<fvcjca=gmail.com@groups.io> wrote:

2019-01-06 14:39 
3.3M

On Apr 3, 2019, at 8:30 AM, John Wiseman <john.wiseman@...> wrote:

Looks like the $port$call construct isn’t being recognised. What version of
LinBPQ are you running? The PAT gateway feature isn’t in the released
version, only in the beta.

73,
John

________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 03 April 2019 15:48
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

PROGRESS!

Here's the latest;

pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 07:42:42 Connecting to WL2K (telnet)...
2019/04/03 07:42:42 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


My Telnet Section of bpq32.cfg
; ********************PORT 3  TELNET **************************************
;3
PORT
 ID=Telnet Server
 DRIVER=Telnet
 CONFIG
    LOGGING=1
    DisconnectOnClose=0     ;  1 = closes window when you bye
    TCPPORT=8010
    FBBPORT=8011
    HTTPPORT=8080
    LOGINPROMPT=user:
    PASSWORDPROMPT=password:
    MAXSESSIONS=10
    RELAYAPPL=BBS
    CMS=1
    CMSCALL=K6FVC-11       ; CMS Access K6FVC (with SSID if used)
    CMSPASS=password     ; WL2K sysop password
    FALLBACKTORELAY=1    ; will try to get to RMS RELAY if CMS unavaiable
    RELAYHOST=192.168.1.21  ; put the name or ip number of your RMS_RELAY
here
    CTEXT=Welcome to K6FVC Telnet Server\n Enter ? for list of commands\n\n
    USER=k6fvc,password,K6FVC1,,SYSOP
   ; USER=username2,password2,K6FVC2,,
; add as many as you like
ENDPORT













John Wiseman
 

Odd,

I copied your command onto my system, just changing the IP address to point
to my pi, and got through to the node and tried to connect.

D:\pat\pat connect telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k
2019/04/03 21:47:18 Connecting to WL2K (telnet)...
2019/04/03 21:47:18 Connected to 10.8.0.1:8772 (tcp)
POGO4:G8BPQ-9} Failure with K6FVC-11
2019/04/03 21:49:16 Got interrupt, disconnecting...
2019/04/03 21:49:16 Exchange failed: unexpected EOF

Could you send me your Telnet log (Telnet_20190403.log)?

Thanks,
John



________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of Fred Cunha
Sent: 03 April 2019 21:08
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

Using the 032719 Beta Version of pilinbpq


Command Line:
pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 13:03:23 Connecting to WL2K (telnet)...
2019/04/03 13:03:23 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


GUI:
2019/04/03 13:04:28 Connecting to WL2K (telnet)...
2019/04/03 13:04:28 Connected to 127.0.0.1:8772 (tcp)
*** Failure with K6FVC-11

On Apr 3, 2019, at 12:18 PM, Fred Cunha via Groups.Io
<fvcjca=gmail.com@groups.io> wrote:

Thank You John. 

both versions same results 


On Apr 3, 2019, at 11:58 AM, Fred Cunha via Groups.Io
<fvcjca=gmail.com@groups.io> wrote:

actually 

2019-03-27 20:08 
3.4M

On Apr 3, 2019, at 11:45 AM, Fred Cunha via Groups.Io
<fvcjca=gmail.com@groups.io> wrote:

2019-01-06 14:39 
3.3M

On Apr 3, 2019, at 8:30 AM, John Wiseman <john.wiseman@...> wrote:

Looks like the $port$call construct isn’t being recognised. What version of
LinBPQ are you running? The PAT gateway feature isn’t in the released
version, only in the beta.

73,
John

________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 03 April 2019 15:48
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

PROGRESS!

Here's the latest;

pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 07:42:42 Connecting to WL2K (telnet)...
2019/04/03 07:42:42 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


My Telnet Section of bpq32.cfg
; ********************PORT 3  TELNET **************************************
;3
PORT
 ID=Telnet Server
 DRIVER=Telnet
 CONFIG
    LOGGING=1
    DisconnectOnClose=0     ;  1 = closes window when you bye
    TCPPORT=8010
    FBBPORT=8011
    HTTPPORT=8080
    LOGINPROMPT=user:
    PASSWORDPROMPT=password:
    MAXSESSIONS=10
    RELAYAPPL=BBS
    CMS=1
    CMSCALL=K6FVC-11       ; CMS Access K6FVC (with SSID if used)
    CMSPASS=password     ; WL2K sysop password
    FALLBACKTORELAY=1    ; will try to get to RMS RELAY if CMS unavaiable
    RELAYHOST=192.168.1.21  ; put the name or ip number of your RMS_RELAY
here
    CTEXT=Welcome to K6FVC Telnet Server\n Enter ? for list of commands\n\n
    USER=k6fvc,password,K6FVC1,,SYSOP
   ; USER=username2,password2,K6FVC2,,
; add as many as you like
ENDPORT


Fred Cunha
 

Using the 032719 Beta Version of pilinbpq


Command Line:
2019/04/03 13:03:23 Connecting to WL2K (telnet)...
2019/04/03 13:03:23 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


GUI:
2019/04/03 13:04:28 Connecting to WL2K (telnet)...
2019/04/03 13:04:28 Connected to 127.0.0.1:8772 (tcp)
*** Failure with K6FVC-11



On Apr 3, 2019, at 12:18 PM, Fred Cunha via Groups.Io <fvcjca@...> wrote:

Thank You John. 

both versions same results 

On Apr 3, 2019, at 11:58 AM, Fred Cunha via Groups.Io <fvcjca@...> wrote:

actually 

2019-03-27 20:08 3.4M

On Apr 3, 2019, at 11:45 AM, Fred Cunha via Groups.Io <fvcjca@...> wrote:

2019-01-06 14:39 3.3M

On Apr 3, 2019, at 8:30 AM, John Wiseman <john.wiseman@...> wrote:

Looks like the $port$call construct isn’t being recognised. What version of
LinBPQ are you running? The PAT gateway feature isn’t in the released
version, only in the beta.

73,
John

________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 03 April 2019 15:48
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

PROGRESS!

Here's the latest;

pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 07:42:42 Connecting to WL2K (telnet)...
2019/04/03 07:42:42 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


My Telnet Section of bpq32.cfg
; ********************PORT 3  TELNET **************************************
;3
PORT
 ID=Telnet Server
 DRIVER=Telnet
 CONFIG
    LOGGING=1
    DisconnectOnClose=0     ;  1 = closes window when you bye
    TCPPORT=8010
    FBBPORT=8011
    HTTPPORT=8080
    LOGINPROMPT=user:
    PASSWORDPROMPT=password:
    MAXSESSIONS=10
    RELAYAPPL=BBS
    CMS=1
    CMSCALL=K6FVC-11       ; CMS Access K6FVC (with SSID if used)
    CMSPASS=password     ; WL2K sysop password
    FALLBACKTORELAY=1    ; will try to get to RMS RELAY if CMS unavaiable
    RELAYHOST=192.168.1.21  ; put the name or ip number of your RMS_RELAY
here
    CTEXT=Welcome to K6FVC Telnet Server\n Enter ? for list of commands\n\n
    USER=k6fvc,password,K6FVC1,,SYSOP
   ; USER=username2,password2,K6FVC2,,
; add as many as you like
ENDPORT










Fred Cunha
 
Edited

Thank You John. 
 
both versions same results 

On Apr 3, 2019, at 11:58 AM, Fred Cunha via Groups.Io <fvcjca@...> wrote:
actually 

2019-03-27 20:08  3.4M
 
On Apr 3, 2019, at 11:45 AM, Fred Cunha via Groups.Io <fvcjca@...> wrote:
2019-01-06 14:39  3.3M
 
On Apr 3, 2019, at 8:30 AM, John Wiseman <john.wiseman@...> wrote:
Looks like the $port$call construct isn’t being recognised. What version of
LinBPQ are you running? The PAT gateway feature isn’t in the released
version, only in the beta.

73,
John

________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 03 April 2019 15:48
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

PROGRESS!

Here's the latest;

pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 07:42:42 Connecting to WL2K (telnet)...
2019/04/03 07:42:42 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


My Telnet Section of bpq32.cfg
; ********************PORT 3  TELNET **************************************
;3
PORT
 ID=Telnet Server
 DRIVER=Telnet
 CONFIG
    LOGGING=1
    DisconnectOnClose=0     ;  1 = closes window when you bye
    TCPPORT=8010
    FBBPORT=8011
    HTTPPORT=8080
    LOGINPROMPT=user:
    PASSWORDPROMPT=password:
    MAXSESSIONS=10
    RELAYAPPL=BBS
    CMS=1
    CMSCALL=K6FVC-11       ; CMS Access K6FVC (with SSID if used)
    CMSPASS=     ; WL2K sysop password
    FALLBACKTORELAY=1    ; will try to get to RMS RELAY if CMS unavaiable
    RELAYHOST=192.168.1.21  ; put the name or ip number of your RMS_RELAY
here
    CTEXT=Welcome to K6FVC Telnet Server\n Enter ? for list of commands\n\n
    USER=k6fvc,password,K6FVC1,,SYSOP
   ; USER=username2,password2,K6FVC2,,
; add as many as you like
ENDPORT






Fred Cunha
 
Edited

actually 

2019-03-27 20:08  3.4M
 

On Apr 3, 2019, at 11:45 AM, Fred Cunha via Groups.Io <fvcjca@...> wrote:
2019-01-06 14:39  3.3M
 
On Apr 3, 2019, at 8:30 AM, John Wiseman <john.wiseman@...> wrote:
Looks like the $port$call construct isn’t being recognised. What version of
LinBPQ are you running? The PAT gateway feature isn’t in the released
version, only in the beta.

73,
John

________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 03 April 2019 15:48
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

PROGRESS!

Here's the latest;

pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 07:42:42 Connecting to WL2K (telnet)...
2019/04/03 07:42:42 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


My Telnet Section of bpq32.cfg
; ********************PORT 3  TELNET **************************************
;3
PORT
 ID=Telnet Server
 DRIVER=Telnet
 CONFIG
    LOGGING=1
    DisconnectOnClose=0     ;  1 = closes window when you bye
    TCPPORT=8010
    FBBPORT=8011
    HTTPPORT=8080
    LOGINPROMPT=user:
    PASSWORDPROMPT=password:
    MAXSESSIONS=10
    RELAYAPPL=BBS
    CMS=1
    CMSCALL=K6FVC-11       ; CMS Access K6FVC (with SSID if used)
    CMSPASS=     ; WL2K sysop password
    FALLBACKTORELAY=1    ; will try to get to RMS RELAY if CMS unavaiable
    RELAYHOST=192.168.1.21  ; put the name or ip number of your RMS_RELAY
here
    CTEXT=Welcome to K6FVC Telnet Server\n Enter ? for list of commands\n\n
    USER=k6fvc,password,K6FVC1,,SYSOP
   ; USER=username2,password2,K6FVC2,,
; add as many as you like
ENDPORT






Fred Cunha
 
Edited

2019-01-06 14:39  3.3M
 

On Apr 3, 2019, at 8:30 AM, John Wiseman <john.wiseman@...> wrote:
Looks like the $port$call construct isn’t being recognised. What version of
LinBPQ are you running? The PAT gateway feature isn’t in the released
version, only in the beta.

73,
John

________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 03 April 2019 15:48
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

PROGRESS!

Here's the latest;

pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 07:42:42 Connecting to WL2K (telnet)...
2019/04/03 07:42:42 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


My Telnet Section of bpq32.cfg
; ********************PORT 3  TELNET **************************************
;3
PORT
 ID=Telnet Server
 DRIVER=Telnet
 CONFIG
    LOGGING=1
    DisconnectOnClose=0     ;  1 = closes window when you bye
    TCPPORT=8010
    FBBPORT=8011
    HTTPPORT=8080
    LOGINPROMPT=user:
    PASSWORDPROMPT=password:
    MAXSESSIONS=10
    RELAYAPPL=BBS
    CMS=1
    CMSCALL=K6FVC-11       ; CMS Access K6FVC (with SSID if used)
    CMSPASS=    ; WL2K sysop password
    FALLBACKTORELAY=1    ; will try to get to RMS RELAY if CMS unavaiable
    RELAYHOST=192.168.1.21  ; put the name or ip number of your RMS_RELAY
here
    CTEXT=Welcome to K6FVC Telnet Server\n Enter ? for list of commands\n\n
    USER=k6fvc,password,K6FVC1,,SYSOP
   ; USER=username2,password2,K6FVC2,,
; add as many as you like
ENDPORT






John Wiseman
 

Looks like the $port$call construct isn’t being recognised. What version of
LinBPQ are you running? The PAT gateway feature isn’t in the released
version, only in the beta.

73,
John

________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 03 April 2019 15:48
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

PROGRESS!

Here's the latest;

pi@raspberrypi2:~ $ pat connect
telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 07:42:42 Connecting to WL2K (telnet)...
2019/04/03 07:42:42 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


My Telnet Section of bpq32.cfg
; ********************PORT 3  TELNET **************************************
;3
PORT
 ID=Telnet Server
 DRIVER=Telnet
 CONFIG
    LOGGING=1
    DisconnectOnClose=0     ;  1 = closes window when you bye
    TCPPORT=8010
    FBBPORT=8011
    HTTPPORT=8080
    LOGINPROMPT=user:
    PASSWORDPROMPT=password:
    MAXSESSIONS=10
    RELAYAPPL=BBS
    CMS=1
    CMSCALL=K6FVC-11       ; CMS Access K6FVC (with SSID if used)
    CMSPASS=iamn0wham      ; WL2K sysop password
    FALLBACKTORELAY=1    ; will try to get to RMS RELAY if CMS unavaiable
    RELAYHOST=192.168.1.21  ; put the name or ip number of your RMS_RELAY
here
    CTEXT=Welcome to K6FVC Telnet Server\n Enter ? for list of commands\n\n
    USER=k6fvc,password,K6FVC1,,SYSOP
   ; USER=username2,password2,K6FVC2,,
; add as many as you like
ENDPORT


Fred Cunha
 
Edited

PROGRESS!

Here's the latest;

pi@raspberrypi2:~ $ pat connect telnet://k6fvc:CMSTelnet$4$k6fvc-11@....0.1:8772/wl2k 
2019/04/03 07:42:42 Connecting to WL2K (telnet)...
2019/04/03 07:42:42 Connected to 127.0.0.1:8772 (tcp)
No CMS connection available - using local BPQMail
ALIAS:K6FVC-7} Invalid command - Enter ? for command list


My Telnet Section of bpq32.cfg
; ********************PORT 3  TELNET **************************************
;3
PORT
 ID=Telnet Server
 DRIVER=Telnet
 CONFIG
    LOGGING=1
    DisconnectOnClose=0     ;  1 = closes window when you bye
    TCPPORT=8010
    FBBPORT=8011
    HTTPPORT=8080
    LOGINPROMPT=user:
    PASSWORDPROMPT=password:
    MAXSESSIONS=10
    RELAYAPPL=BBS
    CMS=1
    CMSCALL=K6FVC-11       ; CMS Access K6FVC (with SSID if used)
    CMSPASS=password      ; WL2K sysop password
    FALLBACKTORELAY=1    ; will try to get to RMS RELAY if CMS unavaiable
    RELAYHOST=192.168.1.21  ; put the name or ip number of your RMS_RELAY here
    CTEXT=Welcome to K6FVC Telnet Server\n Enter ? for list of commands\n\n
    USER=k6fvc,password,K6FVC1,,SYSOP
   ; USER=username2,password2,K6FVC2,,
; add as many as you like
ENDPORT


John Wiseman
 

Sorry, I’ve just had a closer look at your BPQ32.cfg. You need RELAYAPPL=BBS
to tell linbpq to listen on port 8772. That is why you get connection
refused.

On the command line you need

pat connect telnet://k6fvc:CMSTelnet$4$k6fvc-10@....0.1:8772/wl2k

73, John

________________________________________

From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 03 April 2019 13:28
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

Thank You John for your help... I have tried both the gui and command line.
Also, I am on the pi platform. 

When using the gui, I get:
2019/04/03 05:23:57 Connecting to WL2K (telnet)...
2019/04/03 05:23:57 Unable to establish connection to remote: dial tcp
127.0.0.1:8772: connect: connection refused

When I use the command line I get:
pi@raspberrypi2:~ $ pat connect
//k6fvc:CMSTelnet$4$k6fvc-10@....0.1:8772/wl2k2019/04/03 05:22:43
Connecting to WL2K ()...
2019/04/03 05:22:43 Unable to establish connection to remote: No dialer has
been registered for this scheme


Fred Cunha
 

Thank You John for your help... I have tried both the gui and command line. Also, I am on the pi platform. 

When using the gui, I get:
2019/04/03 05:23:57 Connecting to WL2K (telnet)...
2019/04/03 05:23:57 Unable to establish connection to remote: dial tcp 127.0.0.1:8772: connect: connection refused

When I use the command line I get:
pi@raspberrypi2:~ $ pat connect //k6fvc:CMSTelnet$4$k6fvc-10@....0.1:8772/wl2k2019/04/03 05:22:43 Connecting to WL2K ()...
2019/04/03 05:22:43 Unable to establish connection to remote: No dialer has been registered for this scheme
 


John Wiseman
 

I'd only ever used the web gui, not the command line.

This works for me. It connects to BPQ Node using telnet to 127.0.0.1:8772
then connects out using BPQ Port 8 (my ARDOP port) to RMS Gateway GM8BPQ-10
using mycall GM8BPQ. To connect to a different gateway change gm8bpq-10 to
that call.

D:\pat\pat connect telnet://gm8bpq:CMSTelnet$8$gm8bpq-10@....0.1:8772/wl2k
2019/04/03 07:17:10 Connecting to WL2K (telnet)...
2019/04/03 07:17:10 Connected to 127.0.0.1:8772 (tcp)
ARDOP} MYCALL NOW GM8BPQ
*** Connected to GM8BPQ-10
BPQ32 Switch, Skigersta
*** GM8BPQ Connected to CMS
[WL2K-5.0-B2FWIHJM$]
;PQ: 45889843
CMS via G8BPQ >
FF
FQ
2019/04/03 07:17:58 Disconnected.

This also works with pat connect mytelnet with config containing

"connect_aliases": {
"telnet": "telnet://{mycall}:CMSTelnet@...:8772/wl2k",
"mytelnet": "telnet://{mycall}:CMSTelnet$8$gm8bpq-10@....0.1:8772/wl2k"
},

It looks like using the command line required the /wl2k on the end, whereas
using the gui doesn't. I'll update my document to show this.

The 192.168.1.64 in the example is my host address. You should change that
to the address of the machine running BPQ. If it is the same as the machine
running PAT use 127.0.0.1


73,
John







________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 02 April 2019 23:17
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

Leaving off the freq part and deleting the rig info from the pat config,
this is what I get...
plain telnet works OK... It's my 'telardop' which is the 'special' telnet

pi@raspberrypi2:~ $ pat connect telnet
2019/04/02 15:06:32 Connecting to WL2K (telnet)...
2019/04/02 15:06:33 Connected to 52.4.206.229:8772 (tcp)
[WL2K-5.0-B2FWIHJM$]
;PQ: 34048209
CMS>
FF
FQ
2019/04/02 15:06:33 Disconnected.
pi@raspberrypi2:~ $ pat connect telardop
2019/04/02 15:06:41 Invalid or missing target callsign
pi@raspberrypi2:~ $ pat connect telnet:///K7GJT
2019/04/02 15:07:28 Connecting to K7GJT (telnet)...
2019/04/02 15:07:28 Unable to establish connection to remote: dial tcp:
missing address

PAT CONFIG:
...
  "connect_aliases": {


    "telnet": "telnet://{mycall}:CMSTelnet@...:8772/wl2k",
    "telardop": "telnet://{mycall}:CMSTelnet$4$K7GJT@....64:8772"
    Where is this IP address set at from above???
...
"telardop": {
    "listen_addr": ":8774",
    "password": ""
...

MUCH THANKS!


Fred Cunha
 

Leaving off the freq part and deleting the rig info from the pat config, this is what I get...
plain telnet works OK... It's my 'telardop' which is the 'special' telnet

pi@raspberrypi2:~ $ pat connect telnet
2019/04/02 15:06:32 Connecting to WL2K (telnet)...
2019/04/02 15:06:33 Connected to 52.4.206.229:8772 (tcp)
[WL2K-5.0-B2FWIHJM$]
;PQ: 34048209
CMS>
>FF
FQ
2019/04/02 15:06:33 Disconnected.
pi@raspberrypi2:~ $ pat connect telardop
2019/04/02 15:06:41 Invalid or missing target callsign
pi@raspberrypi2:~ $ pat connect telnet:///K7GJT
2019/04/02 15:07:28 Connecting to K7GJT (telnet)...
2019/04/02 15:07:28 Unable to establish connection to remote: dial tcp: missing address

PAT CONFIG:
...
  "connect_aliases": {
    "telnet": "telnet://{mycall}:CMSTelnet@...:8772/wl2k",
    "telardop": "telnet://{mycall}:CMSTelnet$4$K7GJT@....64:8772"
    Where is this IP address set at from above???
...
"telardop": {
    "listen_addr": ":8774",
    "password": ""
...

MUCH THANKS!