Need A GOOD USB cable. Shielded and with Ferrite cores on it to keep RFI out. Also keep the Pi as far away from the TX as possible. Get BlueMail for Android On Mar 15, 2022, at 14:16, Jimmi - OZ4HJ

When I couldn’t get wjst to work I tried flrig with didn’t work either… I think I worked it out, it works now. It was the timeout timer in the icom 7300, I adjustment it and it works. Now the

Hello Jimmi, I am a bit confused with the screen captures you provided. It looks like you are using FLRIG and at the same time telling WSJT-S to control the 7300. If you are using FLRIG as your

Check out KM4ACK website for Build-A-Pi apps on RaspberryPi. or W3DJS for HamPi 2.0.

I started with HamPi but switched over to Build-a-Pi by KM4ACK. You really can't go wrong with either but my preference, for what I like to do, is Build-a-Pi. It's an incredible ham radio software

Hi. I’m trying to connect my raspberry pi zero 2w to my Icom 7300. The Pi is running Build a Pi. I get this errors when I try to connect: Can Anybody help ? 73 - Jimmi - OZ4HJ

KM4ACK has made a batch file program that allows you to build up a Pi for ham use with a variety of programs you can choose. Look for "Build-a-Pi" or BAP. He has a YouTube video that takes you through

There is a complete distribution for ham, ham-pi. Their mailing list is here: https://groups.io/g/Ham-Pi And the image can be downloaded from here: https://sourceforge.net/projects/hampi/ Get BlueMail

I have 2 pi's. A 3 and a 4 with a touch screen. Not much done with them until now. Now want to setup a "HAM" machine. Flrig/digi,wsjtx,js8call,jtdx would recomendet. Most run with Yaesu radios. Mb

Thanks. How do I get the "old 32 bit version" be cores the version 2.0 is not running very good. the usb port is not showing and it runs slow. 73 OZ4JH

Won't run slower. Pi Zero 2W is as fast as the pi 3B+ Get BlueMail for Android On Mar 11, 2022, at 14:26, shulerb <shulerburton@...> wrote:

Make Sure you download the older 32 bit version and it’s going to be slower… some memory intensive ones may not run. -- Shuler Burton Consultant, Burton

Hi Can a Raspberry Pi Zero 2 W run Ham Pi ? Is it just to download the Ham Pi image and flash it over on the SD card ? Is there a How to get started guide, I'm brand new to Raspberry Pi. 73 OZ4HJ

I suggest connecting a 5-ohm or even a 1-ohm load across the output (no R-Pi) and then measuring the voltage. Run it until the regulator gets uncomfortably warm and if that happens very quickly maybe

Hi, I agree. I have an official RPI supply and got the low voltage warning (on RPI2,3 and 4). Checked the voltage and it shows 5.14V. Current consumption was about 1A. I bought one of these of the

Also don't forget that anything that is pulling power from one of the USB ports can cause low voltage issues even with the proper supply. Total power all 4 USB ports combines can provide is 1.2A Get

Fellow Hams: I will be giving a presentation about how to make FT8 contacts using HamPi 2.0 on March 12, 2022 @ 4PM Eastern Time (21:00 UTC) at the QSO Today Virtual Ham Expo. Here is the full

you betcha, especially the cords. Marty kd8bj

What is this thing with available "official" power supplies being capable of no more than the Pi requires? Why not make one capable of say 6 amps (or even more) and a short/heavier cord to reduce

Agree with the above comments. The power supply for the Pi4 is fairly critical. I've seen issues with my LCD display when running off a battery, which then promptly went away with using the "approved"