Re: pi9k6 Winlink Pat ARDOP

John Wiseman
 

I'd only ever used the web gui, not the command line.

This works for me. It connects to BPQ Node using telnet to 127.0.0.1:8772
then connects out using BPQ Port 8 (my ARDOP port) to RMS Gateway GM8BPQ-10
using mycall GM8BPQ. To connect to a different gateway change gm8bpq-10 to
that call.

D:\pat\pat connect telnet://gm8bpq:CMSTelnet$8$gm8bpq-10@....0.1:8772/wl2k
2019/04/03 07:17:10 Connecting to WL2K (telnet)...
2019/04/03 07:17:10 Connected to 127.0.0.1:8772 (tcp)
ARDOP} MYCALL NOW GM8BPQ
*** Connected to GM8BPQ-10
BPQ32 Switch, Skigersta
*** GM8BPQ Connected to CMS
[WL2K-5.0-B2FWIHJM$]
;PQ: 45889843
CMS via G8BPQ >
FF
FQ
2019/04/03 07:17:58 Disconnected.

This also works with pat connect mytelnet with config containing

"connect_aliases": {
"telnet": "telnet://{mycall}:CMSTelnet@...:8772/wl2k",
"mytelnet": "telnet://{mycall}:CMSTelnet$8$gm8bpq-10@....0.1:8772/wl2k"
},

It looks like using the command line required the /wl2k on the end, whereas
using the gui doesn't. I'll update my document to show this.

The 192.168.1.64 in the example is my host address. You should change that
to the address of the machine running BPQ. If it is the same as the machine
running PAT use 127.0.0.1


73,
John







________________________________________
From: RaspberryPi-4-HamRadio@groups.io
[mailto:RaspberryPi-4-HamRadio@groups.io] On Behalf Of fvcjca@...
Sent: 02 April 2019 23:17
To: RaspberryPi-4-HamRadio@groups.io
Subject: Re: [RaspberryPi-4-HamRadio] pi9k6 Winlink Pat ARDOP

Leaving off the freq part and deleting the rig info from the pat config,
this is what I get...
plain telnet works OK... It's my 'telardop' which is the 'special' telnet

pi@raspberrypi2:~ $ pat connect telnet
2019/04/02 15:06:32 Connecting to WL2K (telnet)...
2019/04/02 15:06:33 Connected to 52.4.206.229:8772 (tcp)
[WL2K-5.0-B2FWIHJM$]
;PQ: 34048209
CMS>
FF
FQ
2019/04/02 15:06:33 Disconnected.
pi@raspberrypi2:~ $ pat connect telardop
2019/04/02 15:06:41 Invalid or missing target callsign
pi@raspberrypi2:~ $ pat connect telnet:///K7GJT
2019/04/02 15:07:28 Connecting to K7GJT (telnet)...
2019/04/02 15:07:28 Unable to establish connection to remote: dial tcp:
missing address

PAT CONFIG:
...
  "connect_aliases": {


    "telnet": "telnet://{mycall}:CMSTelnet@...:8772/wl2k",
    "telardop": "telnet://{mycall}:CMSTelnet$4$K7GJT@....64:8772"
    Where is this IP address set at from above???
...
"telardop": {
    "listen_addr": ":8774",
    "password": ""
...

MUCH THANKS!

Join RaspberryPi-4-HamRadio@groups.io to automatically receive all group messages.