Hi Gerry, Add this to the above questions. Looking back, I think a little clarification in activating Horn Master is needed. 1/ The firmware must be version 9-3-2 (in one of the Diesel loco

Hi Gerry, Perhaps I'm not so familiar with Feature 145 after all. I thought you were referring to a Feature map number. Since this is a new decoder: 1/ What would cause the CV 53.1.1 = 143

Hi Gerry, The non-working pop-up issue is on the page before I can choose OPs Mode or Service Mode. The decoder is 'new' so it's address would likely be set to "Short address 3". However, this

Hi Rich, Just a heads up, the Keep Alive interferes with loading firmware (using Quantum Upgrade). You can add a connector to the Keep Alive while installing to allow unplugging if you plan to

Thanks for that Gerry explains some things I'm experiencing here./Bob Menzies On Sep 5, 2016 3:13 PM, "g_pruss@... [QSIndustries]" <QSIndustries@...> wrote:

KJ, >>> 1/ ... None of the buttons do anything <<< If you have selected Operations Mode in the QCVM control bar, the dialog, clicking the Read Out Model Number button should cause the locomotive to

OK, thanks KJ. I downloaded the diagram and will make the install in a few days. Rich Gettysburg

Hi Gerry, I haven't had time to go through CV Manager again but I'll comment on your comments. 1/ The first page of CV Manager, after clicking File --> "New" has a button that reads "About". If

KJ, >>> 1/ ... Shouldn't the "About" pop up, on the first page, allow you to see or hear the type of decoder you have, so that you may select the correct decoder? <<< What if you already know the

Hi Rich, From the Files (above) folder - see the file named QSI Titan A Complete Diagram PDF. In it is a drawing of the Titan A that we can use for reference. The TCS Keep Alive is designed for

I am asking for the right places to connect a TCS Keep Alive circuit to my Titan A decoder. I just finished an install and the engine drops out from time to time. Thanks, Rich Gettysburg, PA

Hi Gerry, Thank you for your reply. 1/ I didn't get to the page, where I had a choice of OPs Mode or Service Mode. It was at the first page where you choose "New" and select your Quantum Decoder.

KJ, >>> 1/ "About Decoder" button brings up a pop-up screen in which only the "Close" button does anything. <<< I just tried this using QCVM 3.1.0.7 and 1161-567v9_3_2 firmware. The About Decoder

KJ, >>> Can one enable Horn Master without enabling all CVs? <<< Enabling the Horn Master CV's in QCVM does enable the CV's in the decoder and does not mean that the decoder's firmware supports these

Thanks Gerry! Now can we answer the "ATTN: QSI - Update" post? KJ

Hi Gerry, Thanks for your replies. I don't have CV Manager running at this moment (as explained in another email - my system is dual boot). In an earlier post (by Tim - CV Manager Issues) Bob

KJ, A query of CV7 yields just the major version number. (CV7 is a standard NMRA CV of just one byte.) Writing "1" to CV56.255 Play Build Information causes the decoder to speak out <major version> .

KJ, The order for feature 145 is Disconnect -> Standby -> Shutdown. If the decoder is in neutral (NFF/NFR) double pressing F9 puts the decoder in Disconnect. If the decoder is in Standby, double

KJ, If you select "Options | Enable Only Supported CV's" you will not have these issues. If you select "Options | Enable All CV's" all the CV's in QuantumCVManager are enabled, whether or not the

Hello all, Using the Quantum Programmer and Quantum Update software (written for the neophytes who may be reading) I loaded the following sound file: 1161-567 version 9-3-2. The original sound