|
40m qcx+ no rf power
#qcx40
Okay,. So I rechecked all the windings and all the solder joints, they all seem to be good to me. No shorts or anything thing like that. Upon diagnosing I did notice I am getting power out to the ante
Okay,. So I rechecked all the windings and all the solder joints, they all seem to be good to me. No shorts or anything thing like that. Upon diagnosing I did notice I am getting power out to the ante
|
By
Darren KN4WML
· #52252
·
|
|
40m qcx+ no rf power
#qcx40
Okay,. So after arguing with the son to do his school work for weeks I finally got around to working on the qcx+. I went ahead and purchased all new BS170 & MPS751 + the IC2. From my power supply Im g
Okay,. So after arguing with the son to do his school work for weeks I finally got around to working on the qcx+. I went ahead and purchased all new BS170 & MPS751 + the IC2. From my power supply Im g
|
By
Darren KN4WML
· #52118
·
|
|
40m qcx+ no rf power
#qcx40
Thanks Ron, I'll give that a go. I'm not to familiar with this type of circuitry but I was leaning on Q6. I'll probably just replace the whole cluster. Yeah, I meant to say menu 9 for the test setting
Thanks Ron, I'll give that a go. I'm not to familiar with this type of circuitry but I was leaning on Q6. I'll probably just replace the whole cluster. Yeah, I meant to say menu 9 for the test setting
|
By
Darren KN4WML
· #51431
·
|
|
40m qcx+ no rf power
#qcx40
Thanks Ron for the info, I hope I don't make two many typos, it's about 3am. So apparently the voltages differ from when it's in the test equipment mode (9.2) than when it's in the normal state- I fig
Thanks Ron for the info, I hope I don't make two many typos, it's about 3am. So apparently the voltages differ from when it's in the test equipment mode (9.2) than when it's in the normal state- I fig
|
By
Darren KN4WML
· #51416
·
|
|
40m qcx+ no rf power
#qcx40
Sorry about not getting into much detail about the components, I was about half asleep sending that. I was using the built in DVM on the qcx+ to do the readings, but this time I used my handheld meter
Sorry about not getting into much detail about the components, I was about half asleep sending that. I was using the built in DVM on the qcx+ to do the readings, but this time I used my handheld meter
|
By
Darren KN4WML
· #51407
·
|
|
40m qcx+ no rf power
#qcx40
This group has been a lifesaver,,,,. Ok, I'm having a no rf power issue. I don't have any fancy equipment to do an accurate diagnosis, I'm using a DVM and the onboard testing equipment. First off my P
This group has been a lifesaver,,,,. Ok, I'm having a no rf power issue. I don't have any fancy equipment to do an accurate diagnosis, I'm using a DVM and the onboard testing equipment. First off my P
|
By
Darren KN4WML
· #51313
·
|
|
Rotary encoder acting funny
#problem
Here's another one..... I have my qcx+ built in a different enclosure then what it's built for. Everything The build went ok, everything powers on like it should. The BPF adjustment was in specs, but
Here's another one..... I have my qcx+ built in a different enclosure then what it's built for. Everything The build went ok, everything powers on like it should. The BPF adjustment was in specs, but
|
By
Darren KN4WML
· #51177
·
|
|
Most accurate way to test rf output
#qcx40
Question?? What would you prefer to test for rf power. Oscilloscope or just a regular swr/rf meter. I've never owned one so I was just wondering which of the two is more accurate. I know the scope can
Question?? What would you prefer to test for rf power. Oscilloscope or just a regular swr/rf meter. I've never owned one so I was just wondering which of the two is more accurate. I know the scope can
|
By
Darren KN4WML
· #51062
·
|
|
Question about a different enclosure
#qcx40
#enclosure
Hopefully I answered my own question. Maybe I should read the manual a little better..... So on the modifications page, JP15 & JP16 are the +12v and the ground. Basically I should run the ground as us
Hopefully I answered my own question. Maybe I should read the manual a little better..... So on the modifications page, JP15 & JP16 are the +12v and the ground. Basically I should run the ground as us
|
By
Darren KN4WML
· #50591
·
|
|
Question about a different enclosure
#qcx40
#enclosure
I have a question maybe someone has run into. I'm building a 40m qcx+ in a different enclosure that's designed for this machine. My original 40m qcx has a page in the manual where it shows you the dia
I have a question maybe someone has run into. I'm building a 40m qcx+ in a different enclosure that's designed for this machine. My original 40m qcx has a page in the manual where it shows you the dia
|
By
Darren KN4WML
· #50537
·
|
|
Resistor for qcx+ code?
#40m
#manual
Thanks for the replys The question was brought up in the past so I was able to figure it out pretty quick. Luckily I had about 200 10K's on hand. Now just to decide on an enclusure and finish the buil
Thanks for the replys The question was brought up in the past so I was able to figure it out pretty quick. Luckily I had about 200 10K's on hand. Now just to decide on an enclusure and finish the buil
|
By
Darren KN4WML
· #50332
·
|
|
Resistor for qcx+ code?
#40m
#manual
I have a question about the installation manual, hopefully some others have run into this issue. On page 80 (3.59) of the manual, it says to install the 10K resistor R46. I didn't have one in the cont
I have a question about the installation manual, hopefully some others have run into this issue. On page 80 (3.59) of the manual, it says to install the 10K resistor R46. I didn't have one in the cont
|
By
Darren KN4WML
· #50290
·
|
|
Firmware update
#firmware
#qcx40
Could the update be done with a cpu like the raspberry pi, or orange pi? I have quite a few of those, but I currently don't have an Arduino
Could the update be done with a cpu like the raspberry pi, or orange pi? I have quite a few of those, but I currently don't have an Arduino
|
By
Darren KN4WML
· #49960
·
|
|
Firmware update
#firmware
#qcx40
I have a quick question about the firmware updates. I have the version 1.00 on my 40m qcx. Would it be beneficial to update it or does it really need it? I don't see any issues with the device as it i
I have a quick question about the firmware updates. I have the version 1.00 on my 40m qcx. Would it be beneficial to update it or does it really need it? I don't see any issues with the device as it i
|
By
Darren KN4WML
· #49956
·
|
|
15M
Thanks everyone for the replys and opinions, I'll definitely take them all in to consideration. Yeah- the day I passed my tech liscense I purchased a used Yaesu mobile all mode hf uhf vhf transceiver.
Thanks everyone for the replys and opinions, I'll definitely take them all in to consideration. Yeah- the day I passed my tech liscense I purchased a used Yaesu mobile all mode hf uhf vhf transceiver.
|
By
Darren KN4WML
· #49132
·
|
|
15M
Being im only liscensed as a technician, I know that I'm allocated to only certain frequencies I can use in the hf bands. (Hopefully not for too long, working on the general soon). Has any one ever ex
Being im only liscensed as a technician, I know that I'm allocated to only certain frequencies I can use in the hf bands. (Hopefully not for too long, working on the general soon). Has any one ever ex
|
By
Darren KN4WML
· #49083
·
|
|
Test modes
#test
#qcx40
I have a quick question about the onboard testing modes (voltage & rf). How accurate do they seem & how do I access them?
I have a quick question about the onboard testing modes (voltage & rf). How accurate do they seem & how do I access them?
|
By
Darren KN4WML
· #48742
·
|
|
PA for qcx 40m
#qcx40
I haven't heard of that group before, I'll have to go and check it out, when I get home. Thanks for the info...
I haven't heard of that group before, I'll have to go and check it out, when I get home. Thanks for the info...
|
By
Darren KN4WML
· #48514
·
|
|
PA for qcx 40m
#qcx40
Well the good thing is that it's operational. I went to both the RBN & Websdr and both picked up on a signal. On the few that picked up, they were around 500-600 miles away. I'm guessing that's not to
Well the good thing is that it's operational. I went to both the RBN & Websdr and both picked up on a signal. On the few that picked up, they were around 500-600 miles away. I'm guessing that's not to
|
By
Darren KN4WML
· #48512
·
|
|
PA for qcx 40m
#qcx40
I'm going to try the RBN later on this evening, and see what happens. Hopefully I can get some results on this issue. If not I'll go through the installation again to see if I fumbled something around
I'm going to try the RBN later on this evening, and see what happens. Hopefully I can get some results on this issue. If not I'll go through the installation again to see if I fumbled something around
|
By
Darren KN4WML
· #48477
·
|