|
QCX for 2m VHF? 19 messages
#mods
#vhf
#qcx
#chat
Check out the Ultra PicoKeyer. It can interface to an FM (or SSB) rig to do MCW. Makes it easy for 2m 'CW' (Morse). Here in western Pennsylvania we have a lot of hills so direct 2m QSOs are very limit
Check out the Ultra PicoKeyer. It can interface to an FM (or SSB) rig to do MCW. Makes it easy for 2m 'CW' (Morse). Here in western Pennsylvania we have a lot of hills so direct 2m QSOs are very limit
|
By
Daniel Walter
·
|
|
No TX, No RX, no LCD 9 messages
#chat
As Fred said some of the ICs use 3.3V, some 5V and a few 12-13V Likely cause is IC11 voltage regulator in backward or a short from pins 1 to 3. POOF, happens then. The parts that do not like more than
As Fred said some of the ICs use 3.3V, some 5V and a few 12-13V Likely cause is IC11 voltage regulator in backward or a short from pins 1 to 3. POOF, happens then. The parts that do not like more than
|
By
ajparent1/KB1GMX
·
|
|
installing LCD display
#chat
Installing the LCD connectors into a transceiver PCB can be a little tricky. Here's a method to do it right with no problems. 1 put the male and female pin connectors together after removing the test
Installing the LCD connectors into a transceiver PCB can be a little tricky. Here's a method to do it right with no problems. 1 put the male and female pin connectors together after removing the test
|
By
Syd
·
|
|
no power transmit
#chat
A new chat has been created: GD, QCX 2017 / 2 #2306 - worked vy well with abt 3 Watts until .... In QTH TA3 2019 suddently no transmit. But not the PA Transitors (changed and OK). Today removed Q4 / Q
A new chat has been created: GD, QCX 2017 / 2 #2306 - worked vy well with abt 3 Watts until .... In QTH TA3 2019 suddently no transmit. But not the PA Transitors (changed and OK). Today removed Q4 / Q
|
By
HB9FIH
·
|
|
Si5351 current consumption 9 messages
#chat
Eduard, I did a test of three different firmwares and measured the current consumption. I used the same meter, same hardware, the only change was the Arduino sketch. I don't think giving my exact mA n
Eduard, I did a test of three different firmwares and measured the current consumption. I used the same meter, same hardware, the only change was the Arduino sketch. I don't think giving my exact mA n
|
By
Mike
·
|
|
QCX Party 17 messages
#chat
Hi to all, I'd like to inform you that I placed a short news notice about the QCX-QSO-Party in the CQ-DL, the German monthly hamradio magazine. Maybe that attracts some more operators to join in next
Hi to all, I'd like to inform you that I placed a short news notice about the QCX-QSO-Party in the CQ-DL, the German monthly hamradio magazine. Maybe that attracts some more operators to join in next
|
By
DG2FDD
·
|
|
Lcd 6 messages
#chat
Alan thanks for the suggestions. I ordered a new atmega chip and the 2 105 caps and I now have a working qcx. It was so nice to turn the rig on and immediately watch it come alive. Needless to say att
Alan thanks for the suggestions. I ordered a new atmega chip and the 2 105 caps and I now have a working qcx. It was so nice to turn the rig on and immediately watch it come alive. Needless to say att
|
By
K8ar Ben
·
|
|
Unable to receive anything on my 20m 13 messages
#chat
Hi all, I've tried to listen on 14.074 MHz and I was unable to hear anything. So as a first approach to solve a possible hardware issue, I checked the voltages on the critical points pointed out in th
Hi all, I've tried to listen on 14.074 MHz and I was unable to hear anything. So as a first approach to solve a possible hardware issue, I checked the voltages on the critical points pointed out in th
|
By
gabri22_@...
·
|
|
Use original IC! displayed on QCX 20m 5 messages
#chat
Alan G4ZFQ wrote: Simon, Sorry, I did not realise they are your instructions. I do not use Averdudess but I see you have EEPROM "Write" ticked on your illustration. But maybe that does not matter as n
Alan G4ZFQ wrote: Simon, Sorry, I did not realise they are your instructions. I do not use Averdudess but I see you have EEPROM "Write" ticked on your illustration. But maybe that does not matter as n
|
By
Alan G4ZFQ
·
|
|
Audio amp for QCX 6 messages
#chat
https://drive.google.com/open?id=1CSSM6IN-A7ZDdw5ijkrZiVAnKpd0qUSY PAM8302 2.5 watt Class D audio amp with IKEA plastic cup.
https://drive.google.com/open?id=1CSSM6IN-A7ZDdw5ijkrZiVAnKpd0qUSY PAM8302 2.5 watt Class D audio amp with IKEA plastic cup.
|
By
Peter
·
|
|
Ultimate 3S and separete receiver 4 messages
#chat
Hi Stuart, The basic U3S is Tx only. You have to buy the receiver module and SSB polyphase module kits too and read the manual on how to link these modules with either the U3S Tx or LO module kits. Th
Hi Stuart, The basic U3S is Tx only. You have to buy the receiver module and SSB polyphase module kits too and read the manual on how to link these modules with either the U3S Tx or LO module kits. Th
|
By
KEN G4APB
·
|
|
QRP Labs ultimateS3 3 messages
#chat
Thanks Hans I did try and find that faq . I was so careful , I was distracted by my little one. Keep your eyes open I'll order the it's later. I'm pretty sure the display is ok . It's probably , well
Thanks Hans I did try and find that faq . I was so careful , I was distracted by my little one. Keep your eyes open I'll order the it's later. I'm pretty sure the display is ok . It's probably , well
|
By
...
·
|
|
40 Mtr QCX
#chat
A new chat has been created: hi all what is the full frequency range of the 40 mtr kit View/Join This Chat
A new chat has been created: hi all what is the full frequency range of the 40 mtr kit View/Join This Chat
|
By
hparkie
·
|
|
QCX problems! 3 messages
#chat
I would also check for shorts around the pads and tracks where the three BS170s are soldered. Steve
I would also check for shorts around the pads and tracks where the three BS170s are soldered. Steve
|
By
Steve Nichols
·
|
|
no power out QCX CW 2 messages
#chat
Hi please see:- https://groups.io/g/QRPLabs/message/19676 especially item No# 10 I do like a guessing game. GIVE US A CLUE What have you tried yourself ? Alan
Hi please see:- https://groups.io/g/QRPLabs/message/19676 especially item No# 10 I do like a guessing game. GIVE US A CLUE What have you tried yourself ? Alan
|
By
Alan de G1FXB
·
|
|
QCX40 problem with Keyer
#chat
A new chat has been created: I had the same problem and thought it was the lack of a dot memory but was assured it had one. If you try and use IAMBIC B most of your problems will go away. Jim N6JF Vie
A new chat has been created: I had the same problem and thought it was the lack of a dot memory but was assured it had one. If you try and use IAMBIC B most of your problems will go away. Jim N6JF Vie
|
By
Jim Ford
·
|
|
RD16HHF1 5Watt PA 9 messages
#chat
Got 6 off RD16HHF1 from mitsubishi europe in netherlands. They are Genuine parts. I also obtained some from:- www.anglia-live.com This appears to be the sole UK outlet. There is a lot of discussion, a
Got 6 off RD16HHF1 from mitsubishi europe in netherlands. They are Genuine parts. I also obtained some from:- www.anglia-live.com This appears to be the sole UK outlet. There is a lot of discussion, a
|
By
Alvey Street
·
|
|
QCX was OK 12 messages
#chat
Hi Geoff Maybe I worded it wrongly. I should have said 13v On the Drains before initial key down, Found using the DMM which slowly decreased by virtue of the DMM being across them. Once it had reduced
Hi Geoff Maybe I worded it wrongly. I should have said 13v On the Drains before initial key down, Found using the DMM which slowly decreased by virtue of the DMM being across them. Once it had reduced
|
By
Ian G4GIR
·
|
|
RF Power 54 messages
#chat
I found some notes I took some time back while burning up power transistors attempting the "peak voltage minus some" biasing method with the dummy load, which I do not recommend and especially not wit
I found some notes I took some time back while burning up power transistors attempting the "peak voltage minus some" biasing method with the dummy load, which I do not recommend and especially not wit
|
By
Hazarda Masklo
·
|
|
Band Cycling 3 messages
#chat
A big Thank you!!! Ah! Txs is on page 8 and 10, and I am trying to follow the settings on page 4,5 +6!!! That parameter needs to be mentioned on page 5. T3 Andrew
A big Thank you!!! Ah! Txs is on page 8 and 10, and I am trying to follow the settings on page 4,5 +6!!! That parameter needs to be mentioned on page 5. T3 Andrew
|
By
Andrew Lenton
·
|