Mike, Read it, but was wondering why Linux users say it's more simple than Windows:-) Each to their own.. 73 Alan G4ZFQ

In fact, for any two-pin PowerPole, once you set the 'zero voltage' pin, there are eight possible orientations of the 'power' pin around it. Only two of those orientations can use the roller pin for

kf7rcm: I have read this thread and also your previous one concerning your problems. No offense intended but I think you need to back up a bit - you're getting into detailed component troubleshooting

Don't forget the "Impossible to rework" 0201 size. :^)

Not sure if the resistors I mailed are not smaller than 1mm 0402. Hopefully the are the right size.

Wayne, you can't read RF with a DMM. You need to make an RF probe for the meter if you want to. Google "RF probe" for lots of schematics. The diode can be a silicon switching diode (1N914,

If you were actually reading 0.115 microFARADS, the cap is actually 11.5% large. Jim W4JED On 6/27/22 22:47, kf7rcm via groups.io wrote:

HUH?? Caps don't have any kind of henrys. They have farads. If you are trying to read RF power at the PA drains, using the built-in meter, you are not reading RF power. If you

I cried when I saw the various colors being used. I have some fence chargers that use Black for plus 12 DC and white for ground similar to AC. I have a large number of lipo batteries with XT60

You guys don't read. He is asking about the SMD size. 0402 ??

For two instances of digital work, I used this little guy for the audio in and out. I have an RS232 to USB board the size of a thumb drive & output pins to convert RTS to a PTT signal. Add a USB hub,

On Tue, Jun 28, 2022 at 08:33 AM, Dave Spicer wrote: I also use different colour shells but they all work and make contact perfectly wellNot missing anything. The original post was on using something

Thanks, Alan. Something I hadn’t understood - that the low pass filters as well as the band pass filters are active during receive mode… My audio and RF sweeps attached for reference… not sure

I think I must have missed something here, I use Anderson PowerPole connectors for most leads in my shack, I only run 12v. I also use different colour shells but they all work and make contact

Spot Database Specify query parameters 2602 spots:TimestampCallMHzSNRDriftGridPwrReporterRGridkmazMode 2022-06-27 01:44 AC1JS 3.570004 -27 0 FN54 0.2 NJ1A FN42jl 283 219 2 This is an

On Mon, Jun 27, 2022 at 02:59 PM, August Treubig AG5AT wrote: Mike, Power Poles are the bomb. Converted to them 20 years ago. The more times you plug them in, the better they work.Power Poles (as

I pulled up the tiny plastic strip so I could get the ohm meter on one.. Hit the strip with the meter probe and the resistor flew away.. NTBSA Cut off a strip of 4 units and measured one on the end @

Hi Manuel, Barb, all A great pleasure to meet you and Barb WB2CBA and so many QRP Labs customers too. I took 100 QDX and sold all 100, and took orders for more. Somehow a Yaesu G-2800DXC rotator

Hi Alan, I forget the sequence of events but in trying to get Windows to pick up the QDX some connecting, reconnecting and rebooting of the QDX was tried. Windows seemed to conclude that it was a

Adding my report here- same issue with freshly built rev 3. Posted a waterfall view of the noise here: https://twitter.com/tom_m0lte/status/1541546374596100098?s=21&t=mDBcTzTPiR8_XE-HsPrstA Good luck