Jim: Talk about gov't delays. When I lived in Indiana, the Legislature raised the minimum property tax rate, but also the assessed value rate. My property taxes went from $1167/yr to $4223/yr

I think you're looking for this: http://qrp-labs.com/qcxp It's an updated form factor of the QCX. -- Ryan Flowers - W7RLF MiscDotGeek - QRP and More

Peter, Where can I get info on the new QCX rig that is coming out probably later this year? Is it possible it is a multi band unit? I am just coming up to speed on my 20 meter QCX, but looking

Hi Ted and Hans, I'm so glad you provided that glimpse of Akihabara (especially the photos), as my post had already grown far too long. Family and friends have diagnosed themselves as suffering from

Hi Serge I use these folding feet on my rig which employs very similar boxes to the one destined for the QCX+ https://www.metcase.co.uk/en/Enclosure-Feet/M6420204.htm Roger I have successfully made

Tisha, for your intuitive use: Band:20 meters Output: 30 Watts Voltage: 19 V Heatsink: top of QCX + case Longest transmission, 2 ea. 3x3 CQ, followed by QSO basic exchange of OP, QTH and RST,

I didn't mean to imply that the HW-16 is my only hollow state electronics - just that it's on the bench. I recreated my '60s novice station with a rare, and weird, Mosley CM-1 receiver, Heathkit

I would prefer a wire bail that folds down, rather than folding feet. I find that folding feet (e.g. like on the Drake R8) tend to be flimsy. Roger G3YTN --- *************************** Roger Hill

Hi Serge There are no folding feet. If someone has a suggestion, that could become popular. As supplied, it will, as documented, have four self-adhesive feet. 73 Hans G0UPL http://qrp-labs.com

It is probably a bad idea to seperate the PA transistors (IRF510) too far from the circuit board. Since they are trying to work together in a push-pull arrangement to drive a few amps of RF current

More from a troubleshooting aid point-of-view as components are being replaced when doing a repair. -- 73, Bernie, VE3FWF

Correction: I use a 3S to power the QCX and 2S in series to power the 50W amp. 6S would be too high voltage. John

Yes, Hans, I also see potential for your stalagmites not meeting my stalactites :-D On a different note, will the enclosure have a pair of folding feet under the front?I want to avoid getting a stiff

Hi, short test for IC10 Check again whether the marking on the circuit shows the display (ok, already done 100 times) Use a protective resistor Rp approx. 220 Ohm (against unwanted short circuit), do

Giuseppe, I do not understand. What does it touch? IC1 is on the other side of the board. It's pins are seen at the left side, away from the cover. This cover helps to screen and maybe more

Hi Serge Yes, I see... The wide thickness of your assembly is due to the circuit board and the battery holders all adding up as thickness. Well there are some potential ways you could make it fit.

Sorry Giuseppe...I cannot help as I have never built one, but I am sure there are others here who can help. Roger G3YTN --- *************************** Roger Hill ***************************

Hello everyone, my name is Giuseppe iu8eun. I would like to ask you for help regarding the external screen as shown in the OCXO photo for my U3S multiband. I can't put it because it hits the IC1

I have done investigation on the accuracy of the GPS control using the Synth module in both the PRO-ROCK and the VFO Sig-gen and I also confirm a frequency difference between an off air standard and

I have done investigation on the accuracy of the GPS control using the Synth module in both the PRO-ROCK and the VFO Sig-gen and I also confirm a frequency difference between an off air standard and