Date   

Re: Exporting 80m confirmed list of countries

Larry Banks
 

Hi Megan,
 
Clicking on the “Worked” column will copy the list to your clipboard.  Then just past it to whatever.

73 -- Larry -- W1DYJ

 

Sent: Friday, March 27, 2020 20:14
Subject: [N3FJPSoftwareUsers] Exporting 80m confirmed list of countries
 

I found how to view the list of countries I have confirmed on 80 meters, but is there a way to export just that list?

 

73, Megin, K5IJ


Exporting 80m confirmed list of countries

Megin Murphy
 

I found how to view the list of countries I have confirmed on 80 meters, but is there a way to export just that list?

 

73, Megin, K5IJ


Re: TIME

Les C. VA7RN <les.corris@...>
 

Thank you Scott. I comparing the times in ACLog with the times on the screen of my Icom 7610, which were incorrect. My Bad. Sorry for BW.
73, Les. VA7RN


locked Re: CQ WPX SSB Prep!

Mel Marcus
 

Scott

Thanks that worked.

Mel
NE9A

-------- Original Message --------
Subject: Re: [N3FJPSoftwareUsers] CQ WPX SSB Prep!
From: "Scott Davis via Groups.Io" <SNKDavis@...>
Date: Fri, March 27, 2020 4:51 pm
To: "N3FJPSoftwareUsers@groups.io" <N3FJPSoftwareUsers@groups.io>

Hi Mel,

Thanks for your e-mail.  Click Settings > Setup and choose SSB.  Also, make sure your rig interface is correct.  Both are addressed in this link here:


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Mel Marcus <melm@...>
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Sent: Fri, Mar 27, 2020 5:44 pm
Subject: Re: [N3FJPSoftwareUsers] CQ WPX SSB Prep!

Scott

Install went well except for one thing.  Mode shows as digital and I cant seem to change it to ssb

Mel
NE9A

-------- Original Message --------
Subject: [N3FJPSoftwareUsers] CQ WPX SSB Prep!
From: "Scott Davis via Groups.Io" <SNKDavis@...>
Date: Fri, March 27, 2020 4:22 pm
To: "n3fjpsoftwareusers@groups.io" <n3fjpsoftwareusers@groups.io>

Hi All,

With so many of us home, it sounds like there are going to be a LOT of participants in CQ WPX SSB this weekend!

As always, before you begin operating in this weekend's contest, please take a moment and review this pre contest checklist.  Most of the contest support questions I receive are from those who haven't.  I use it myself, every time.


The software for this weekend's contest is here:


And the CQ WPX rules are here:


I hope to work you!

Enjoy the contest!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


Re: TIME

Scott Davis
 

Hi Les,

Thanks for your e-mail.  Please see this FAQ here:


http://www.n3fjp.com/faq.html#q51

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Les C. VA7RN <les.corris@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Fri, Mar 27, 2020 6:05 pm
Subject: [N3FJPSoftwareUsers] TIME

The time showing on my Amateur Contact Log is incorrect. The local  time is  off by 1 hour ahead and the UTC time is off by 8 hours ahead and I do not see any way to correct this. How can I correct the time?
Les, VA7RN


TIME

Les C. VA7RN <les.corris@...>
 

The time showing on my Amateur Contact Log is incorrect. The local  time is  off by 1 hour ahead and the UTC time is off by 8 hours ahead and I do not see any way to correct this. How can I correct the time?
Les, VA7RN


Re: DX Spotting Question

George Davenport
 

All you should have to do is go to settings then DX Spots, Configure and then uncheck and recheck "Enable DX spots" ..You should not have to shut down the entire program.
--
George-- KM4ODS


locked Re: CQ WPX SSB Prep!

Scott Davis
 

Hi Mel,

Thanks for your e-mail.  Click Settings > Setup and choose SSB.  Also, make sure your rig interface is correct.  Both are addressed in this link here:


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Mel Marcus <melm@...>
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Sent: Fri, Mar 27, 2020 5:44 pm
Subject: Re: [N3FJPSoftwareUsers] CQ WPX SSB Prep!

Scott

Install went well except for one thing.  Mode shows as digital and I cant seem to change it to ssb

Mel
NE9A

-------- Original Message --------
Subject: [N3FJPSoftwareUsers] CQ WPX SSB Prep!
From: "Scott Davis via Groups.Io" <SNKDavis@...>
Date: Fri, March 27, 2020 4:22 pm
To: "n3fjpsoftwareusers@groups.io" <n3fjpsoftwareusers@groups.io>

Hi All,

With so many of us home, it sounds like there are going to be a LOT of participants in CQ WPX SSB this weekend!

As always, before you begin operating in this weekend's contest, please take a moment and review this pre contest checklist.  Most of the contest support questions I receive are from those who haven't.  I use it myself, every time.


The software for this weekend's contest is here:


And the CQ WPX rules are here:


I hope to work you!

Enjoy the contest!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


locked Re: CQ WPX SSB Prep!

Mel Marcus
 

Scott

Install went well except for one thing.  Mode shows as digital and I cant seem to change it to ssb

Mel
NE9A

-------- Original Message --------
Subject: [N3FJPSoftwareUsers] CQ WPX SSB Prep!
From: "Scott Davis via Groups.Io" <SNKDavis@...>
Date: Fri, March 27, 2020 4:22 pm
To: "n3fjpsoftwareusers@groups.io" <n3fjpsoftwareusers@groups.io>

Hi All,

With so many of us home, it sounds like there are going to be a LOT of participants in CQ WPX SSB this weekend!

As always, before you begin operating in this weekend's contest, please take a moment and review this pre contest checklist.  Most of the contest support questions I receive are from those who haven't.  I use it myself, every time.


The software for this weekend's contest is here:


And the CQ WPX rules are here:


I hope to work you!

Enjoy the contest!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


Re: rig Interface

Ed W2LCQ <w2lcq@...>
 

Jim.

Here are settings for the 7100

Icom 7100
Rig Name = Icom
Read Frequency Command = FE FE 88 E0 03 FD
Read Mode Command = FE FE 88 E0 04 FD
Convert To Hex = True
Baud Rate = 19200
Parity = None
Stop Bits = 1
Data Bits = 8
Power Option = RTS

73, Ed Jones W2LCQ

CWops 701 - SKCC 5474T - FISTS 12294 - LICWC
                         Frankford Radio Club



On Mar 27, 2020, at 4:21 PM, James Melville via Groups.Io <jameshmelville@...> wrote:


Scott,
Thanks for the response.  Unfortunately I have gone to that before resorting to asking.  The problem is that I should be able to go to Settings and then rig interface and have it give me a list of interfaces to select from.  When I go there, I have nothing, not one interface!
Jim

On Friday, March 27, 2020, 03:35:48 PM EDT, Scott Davis via Groups.Io <snkdavis@...> wrote:


Hi Jim,

Thanks for your e-mail.  You'll find the successful settings other icom 7100 users have sent along here:


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: jameshmelville via Groups.Io <jameshmelville@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Fri, Mar 27, 2020 3:13 pm
Subject: [N3FJPSoftwareUsers] rig Interface

My call is ND1N and I am a new user of your software.
I have had minimum of issues however, I want to interface my IC7100 to my computer and under "Rig Interface" in Settings I have no interfaces to choose from.
How do I obtain the program for my 7100?
Thanks in advance.
Jim
ND1N


locked CQ WPX SSB Prep!

Scott Davis
 

Hi All,

With so many of us home, it sounds like there are going to be a LOT of participants in CQ WPX SSB this weekend!

As always, before you begin operating in this weekend's contest, please take a moment and review this pre contest checklist.  Most of the contest support questions I receive are from those who haven't.  I use it myself, every time.

http://www.n3fjp.com/help/contestchecklist.html

The software for this weekend's contest is here:


And the CQ WPX rules are here:


I hope to work you!

Enjoy the contest!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


Re: rig Interface

Scott Davis
 

Hi Jim,

Thanks for your follow up and clarification.  Please see this FAQ here (and pay special attention to the note about Icom drivers):


http://www.n3fjp.com/faq.html#q81

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: James Melville via Groups.Io <jameshmelville@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Fri, Mar 27, 2020 4:21 pm
Subject: Re: [N3FJPSoftwareUsers] rig Interface

Scott,
Thanks for the response.  Unfortunately I have gone to that before resorting to asking.  The problem is that I should be able to go to Settings and then rig interface and have it give me a list of interfaces to select from.  When I go there, I have nothing, not one interface!
Jim

On Friday, March 27, 2020, 03:35:48 PM EDT, Scott Davis via Groups.Io <snkdavis@...> wrote:


Hi Jim,

Thanks for your e-mail.  You'll find the successful settings other icom 7100 users have sent along here:


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: jameshmelville via Groups.Io <jameshmelville@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Fri, Mar 27, 2020 3:13 pm
Subject: [N3FJPSoftwareUsers] rig Interface

My call is ND1N and I am a new user of your software.
I have had minimum of issues however, I want to interface my IC7100 to my computer and under "Rig Interface" in Settings I have no interfaces to choose from.
How do I obtain the program for my 7100?
Thanks in advance.
Jim
ND1N


Re: rig Interface

jameshmelville@...
 

Scott,
Thanks for the response.  Unfortunately I have gone to that before resorting to asking.  The problem is that I should be able to go to Settings and then rig interface and have it give me a list of interfaces to select from.  When I go there, I have nothing, not one interface!
Jim

On Friday, March 27, 2020, 03:35:48 PM EDT, Scott Davis via Groups.Io <snkdavis@...> wrote:


Hi Jim,

Thanks for your e-mail.  You'll find the successful settings other icom 7100 users have sent along here:


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: jameshmelville via Groups.Io <jameshmelville@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Fri, Mar 27, 2020 3:13 pm
Subject: [N3FJPSoftwareUsers] rig Interface

My call is ND1N and I am a new user of your software.
I have had minimum of issues however, I want to interface my IC7100 to my computer and under "Rig Interface" in Settings I have no interfaces to choose from.
How do I obtain the program for my 7100?
Thanks in advance.
Jim
ND1N


Re: rig Interface

Scott Davis
 

Hi Jim,

Thanks for your e-mail.  You'll find the successful settings other icom 7100 users have sent along here:


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: jameshmelville via Groups.Io <jameshmelville@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Fri, Mar 27, 2020 3:13 pm
Subject: [N3FJPSoftwareUsers] rig Interface

My call is ND1N and I am a new user of your software.
I have had minimum of issues however, I want to interface my IC7100 to my computer and under "Rig Interface" in Settings I have no interfaces to choose from.
How do I obtain the program for my 7100?
Thanks in advance.
Jim
ND1N


rig Interface

jameshmelville@...
 

My call is ND1N and I am a new user of your software.
I have had minimum of issues however, I want to interface my IC7100 to my computer and under "Rig Interface" in Settings I have no interfaces to choose from.
How do I obtain the program for my 7100?
Thanks in advance.
Jim
ND1N


Win4K3 Integration

Mark
 

Is anyone using the Win4K3 Suite ?  I'm curious if the "F" keys in N3FJP will activate the DVR in a K3 once the two programs are interfaced ?

73
Mark KN7T


Re: CI-V connection on the IC-7300 and AC Log

kc6mie
 

👍

Stephen Spencer

On Mar 26, 2020, at 4:50 PM, Mark W <K3MRK1@...> wrote:


I just hooked mine up last week. All I did was plug it in and it worked. I wasnt expecting that.

--
Mark
K3MRK
Southern PA Amateur Radio Club


Re: CI-V connection on the IC-7300 and AC Log

Mark W
 

I just hooked mine up last week. All I did was plug it in and it worked. I wasnt expecting that.

--
Mark
K3MRK
Southern PA Amateur Radio Club


Re: DX Spotting Question

Jim Wotus
 

Tom

 

Try enabling the 3 Min Keep Alive it’s just below the Enable DX Spotting

 

From: N3FJPSoftwareUsers@groups.io [mailto:N3FJPSoftwareUsers@groups.io] On Behalf Of Tom and Toni Hauer
Sent: Thursday, March 26, 2020 3:54 PM
To: N3FJPSoftwareUsers@groups.io
Subject: Re: [N3FJPSoftwareUsers] DX Spotting Question

 

I have never selected for everything!

 

On Thu, Mar 26, 2020, 5:04 PM Pat Whelton <pwhelton@...> wrote:

That’s exactly what happened to me.  The new computer would go into sleep/hibernation mode every 10 minutes and that would knock out the Telenet link.  Changed the setting from “10 minutes” to “NEVER” and the problem went away.

 

73,

 

Pat – KZ5J

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of John Mathey
Sent: Thursday, March 26, 2020 3:34 PM
To: n3fjpsoftwareusers@groups.io
Subject: Re: [N3FJPSoftwareUsers] DX Spotting Question

 

I had this problem a while ago.  What the problem was for me was the computer was going to sleep or hibernation mode.  Once I turned that off everything stayed connected.  Hope this helps.

 

John/K8AZT


Re: DX Spotting Question

Pat Whelton
 

Sorry that didn’t work for you Tom.  Maybe someone else has a suggestion.  All I can say is I had a similar problem as you described and it worked for me.  Good luck with your problem.

 

73,

 

Pat – KZ5J

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of Tom and Toni Hauer
Sent: Thursday, March 26, 2020 5:54 PM
To: N3FJPSoftwareUsers@groups.io
Subject: Re: [N3FJPSoftwareUsers] DX Spotting Question

 

I have never selected for everything!

 

On Thu, Mar 26, 2020, 5:04 PM Pat Whelton <pwhelton@...> wrote:

That’s exactly what happened to me.  The new computer would go into sleep/hibernation mode every 10 minutes and that would knock out the Telenet link.  Changed the setting from “10 minutes” to “NEVER” and the problem went away.

 

73,

 

Pat – KZ5J

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of John Mathey
Sent: Thursday, March 26, 2020 3:34 PM
To: n3fjpsoftwareusers@groups.io
Subject: Re: [N3FJPSoftwareUsers] DX Spotting Question

 

I had this problem a while ago.  What the problem was for me was the computer was going to sleep or hibernation mode.  Once I turned that off everything stayed connected.  Hope this helps.

 

John/K8AZT