Date   

locked Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Greg Cook
 

OK, I have been able to get AC Log, fldigi, and HRD to all work together at the same time on virtual com port 10 set up with Kevin's instructions.

What other programs have others been able to connect and work properly together with AC Log?

Thanks,

Greg


Begin forwarded message:

From: "Greg Cook via groups.io" <kgregc1@...>
Date: 1/10/2021
To: N3FJPSoftwareUsers@groups.io
Subject: Re: [N3FJPSoftwareUsers] Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Michael,

Thanks for the information.

Could you list the programs that you have been successful with? This will help me and maybe others too.

73,

Greg


On January 10, 2021 at 9:18 AM, Michael WA7SKG <wa7skg@...> wrote:

Yeah, WSJT-X is the weird one that does not seem to play nice with
everything else. I have the same problem. I can have three or four apps
all working just fine via VSPE, then I open WSJT-X and it takes over
from everything else.

If I were to guess, it may be something to do with how often WSJT-X
polls for data. If I were more ambitious and worried about it, I would
set up a serial sniffer to monitor the traffic between devices. Too low
on my priority list to think about.

Michael WA7SKG

Greg Cook via groups.io wrote on 1/9/21 3:47 PM:
Kevin,

I setup VSPE per your instructions. Opened AC Log, set it to the virtual
port and it works. Change frequency on the IC-7300 and it changes on AC
Log.

Opened WSJT-X set it up and it works. Change frequency on the IC-7300
and it changes it on WSJT-X, BUT...the frequency no longer changes on AC
Log. Click Polling and it is blank.

Appreciate any help you can give.

Same happens with RS-BA1 V2 Icom software.

Greg


On January 10, 2021 at 4:41 AM, Kevin Gray <n9vpv@...> wrote:

Start VSPE

Click on Create New Device

Select device type: Splitter, click Next

Data Source Serial Port: COM4 (or whatever the radio serial port is
for your radio) { Are you actually using a 991 ?  and picked the
enhanced port to split ?}

Virtual Serial Port: COM7 (or whichever you want, make sure your
logging programs use this port).

Click settings:

Speed: 57600 (or whatever your radio is currently using)

DTR/RTS: NO

Parity: no

Bits: 8

Stop bits: 1

Click OK

Redirect modem registers: CHECKED

Initial Modem Registers State: RTS: NOT CHECKED, DTR: NOT CHECKED

Once you’re all setup, click the Play button. VSPE should say that the
initialization is OK.

Select the new port in ACLog, make sure all parameters are set, Baud,
Parity, Data, Stop, etc

Then press the /Test/ button on the rig interface form.

If this doesn’t work, send actual screen shots of what YOU have.

73

Kevin

N9VPV

*From:* N3FJPSoftwareUsers@groups.io
<mailto:N3FJPSoftwareUsers@groups.io> <N3FJPSoftwareUsers@groups.io>
*On Behalf Of *Walter Egenmaier
*Sent:* Saturday, January 9, 2021 1:12 PM
*To:* N3FJPSoftwareUsers@groups.io <mailto:N3FJPSoftwareUsers@groups.io>
*Subject:* Re: [N3FJPSoftwareUsers] Does N3FJP work with Eterlogic's
VSPE software to expand single COM4 into virtual ports...if so how?

Kevin, I used the following setup.
https://github.com/rfrht/FT991A-PAT/wiki/appendix-sharing-serial-port
Is that all you need?
I was successfully running on COM 4 and all I did was run VSPE and
then open N3FJP and switched to COM 7 (which is a virtual COM I created.
Walt / WB4ZUT







locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Walter Egenmaier
 

Kevin...I know how the program VSPE works now and can set up multiple scripts for virtual Com ports 7-whatever.
What I don't get is, I can only one script at a time and I can't save more than a single script from what I can tell.
So you do you recommend I create one virtual port for each software, e.g. on Com 4, FLDIGI on Com8, and Winlink /VARA FM on Com 9?
Save 3 separate files and run the one I want to use?
I thought I could run all 3 at the same time, but only one com port shows up.


locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Greg Cook
 

Michael,

Thanks for the information.

Could you list the programs that you have been successful with? This will help me and maybe others too.

73,

Greg


On January 10, 2021 at 9:18 AM, Michael WA7SKG <wa7skg@...> wrote:

Yeah, WSJT-X is the weird one that does not seem to play nice with
everything else. I have the same problem. I can have three or four apps
all working just fine via VSPE, then I open WSJT-X and it takes over
from everything else.

If I were to guess, it may be something to do with how often WSJT-X
polls for data. If I were more ambitious and worried about it, I would
set up a serial sniffer to monitor the traffic between devices. Too low
on my priority list to think about.

Michael WA7SKG

Greg Cook via groups.io wrote on 1/9/21 3:47 PM:
Kevin,

I setup VSPE per your instructions. Opened AC Log, set it to the virtual
port and it works. Change frequency on the IC-7300 and it changes on AC
Log.

Opened WSJT-X set it up and it works. Change frequency on the IC-7300
and it changes it on WSJT-X, BUT...the frequency no longer changes on AC
Log. Click Polling and it is blank.

Appreciate any help you can give.

Same happens with RS-BA1 V2 Icom software.

Greg


On January 10, 2021 at 4:41 AM, Kevin Gray <n9vpv@...> wrote:

Start VSPE

Click on Create New Device

Select device type: Splitter, click Next

Data Source Serial Port: COM4 (or whatever the radio serial port is
for your radio) { Are you actually using a 991 ?  and picked the
enhanced port to split ?}

Virtual Serial Port: COM7 (or whichever you want, make sure your
logging programs use this port).

Click settings:

Speed: 57600 (or whatever your radio is currently using)

DTR/RTS: NO

Parity: no

Bits: 8

Stop bits: 1

Click OK

Redirect modem registers: CHECKED

Initial Modem Registers State: RTS: NOT CHECKED, DTR: NOT CHECKED

Once you’re all setup, click the Play button. VSPE should say that the
initialization is OK.

Select the new port in ACLog, make sure all parameters are set, Baud,
Parity, Data, Stop, etc

Then press the /Test/ button on the rig interface form.

If this doesn’t work, send actual screen shots of what YOU have.

73

Kevin

N9VPV

*From:* N3FJPSoftwareUsers@groups.io
<mailto:N3FJPSoftwareUsers@groups.io> <N3FJPSoftwareUsers@groups.io>
*On Behalf Of *Walter Egenmaier
*Sent:* Saturday, January 9, 2021 1:12 PM
*To:* N3FJPSoftwareUsers@groups.io <mailto:N3FJPSoftwareUsers@groups.io>
*Subject:* Re: [N3FJPSoftwareUsers] Does N3FJP work with Eterlogic's
VSPE software to expand single COM4 into virtual ports...if so how?

Kevin, I used the following setup.
https://github.com/rfrht/FT991A-PAT/wiki/appendix-sharing-serial-port
Is that all you need?
I was successfully running on COM 4 and all I did was run VSPE and
then open N3FJP and switched to COM 7 (which is a virtual COM I created.
Walt / WB4ZUT







locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Michael WA7SKG
 

Yeah, WSJT-X is the weird one that does not seem to play nice with everything else. I have the same problem. I can have three or four apps all working just fine via VSPE, then I open WSJT-X and it takes over from everything else.

If I were to guess, it may be something to do with how often WSJT-X polls for data. If I were more ambitious and worried about it, I would set up a serial sniffer to monitor the traffic between devices. Too low on my priority list to think about.

Michael WA7SKG

Greg Cook via groups.io wrote on 1/9/21 3:47 PM:

Kevin,
I setup VSPE per your instructions. Opened AC Log, set it to the virtual port and it works. Change frequency on the IC-7300 and it changes on AC Log.
Opened WSJT-X set it up and it works. Change frequency on the IC-7300 and it changes it on WSJT-X, BUT...the frequency no longer changes on AC Log. Click Polling and it is blank.
Appreciate any help you can give.
Same happens with RS-BA1 V2 Icom software.
Greg
On January 10, 2021 at 4:41 AM, Kevin Gray <n9vpv@arrl.net> wrote:

Start VSPE

Click on Create New Device

Select device type: Splitter, click Next

Data Source Serial Port: COM4 (or whatever the radio serial port is for your radio) { Are you actually using a 991 ?  and picked the enhanced port to split ?}

Virtual Serial Port: COM7 (or whichever you want, make sure your logging programs use this port).

Click settings:

Speed: 57600 (or whatever your radio is currently using)

DTR/RTS: NO

Parity: no

Bits: 8

Stop bits: 1

Click OK

Redirect modem registers: CHECKED

Initial Modem Registers State: RTS: NOT CHECKED, DTR: NOT CHECKED

Once you’re all setup, click the Play button. VSPE should say that the initialization is OK.

Select the new port in ACLog, make sure all parameters are set, Baud, Parity, Data, Stop, etc

Then press the /Test/ button on the rig interface form.

If this doesn’t work, send actual screen shots of what YOU have.

73

Kevin

N9VPV

*From:* N3FJPSoftwareUsers@groups.io <mailto:N3FJPSoftwareUsers@groups.io> <N3FJPSoftwareUsers@groups.io> *On Behalf Of *Walter Egenmaier
*Sent:* Saturday, January 9, 2021 1:12 PM
*To:* N3FJPSoftwareUsers@groups.io <mailto:N3FJPSoftwareUsers@groups.io>
*Subject:* Re: [N3FJPSoftwareUsers] Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Kevin, I used the following setup.
https://github.com/rfrht/FT991A-PAT/wiki/appendix-sharing-serial-port
Is that all you need?
I was successfully running on COM 4 and all I did was run VSPE and then open N3FJP and switched to COM 7 (which is a virtual COM I created.
Walt / WB4ZUT


locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Greg Cook
 

Kevin,

I setup VSPE per your instructions. Opened AC Log, set it to the virtual port and it works. Change frequency on the IC-7300 and it changes on AC Log.

Opened WSJT-X set it up and it works. Change frequency on the IC-7300 and it changes it on WSJT-X, BUT...the frequency no longer changes on AC Log. Click Polling and it is blank.

Appreciate any help you can give.

Same happens with RS-BA1 V2 Icom software.

Greg


On January 10, 2021 at 4:41 AM, Kevin Gray <n9vpv@...> wrote:

 

Start VSPE

 

Click on Create New Device

Select device type: Splitter, click Next

Data Source Serial Port: COM4 (or whatever the radio serial port is for your radio) { Are you actually using a 991 ?  and picked the enhanced port to split ?}

Virtual Serial Port: COM7 (or whichever you want, make sure your logging programs use this port).

Click settings:

Speed: 57600 (or whatever your radio is currently using)

DTR/RTS: NO

Parity: no

Bits: 8

Stop bits: 1

Click OK

Redirect modem registers: CHECKED

Initial Modem Registers State: RTS: NOT CHECKED, DTR: NOT CHECKED

 

Once you’re all setup, click the Play button. VSPE should say that the initialization is OK.

 

Select the new port in ACLog, make sure all parameters are set, Baud, Parity, Data, Stop, etc

Then press the Test button on the rig interface form.

 

If this doesn’t work, send actual screen shots of what YOU have.

 

73

Kevin

N9VPV

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of Walter Egenmaier
Sent: Saturday, January 9, 2021 1:12 PM
To: N3FJPSoftwareUsers@groups.io
Subject: Re: [N3FJPSoftwareUsers] Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

 

Kevin, I used the following setup.
https://github.com/rfrht/FT991A-PAT/wiki/appendix-sharing-serial-port
Is that all you need?
I was successfully running on COM 4 and all I did was run VSPE and then open N3FJP and switched to COM 7 (which is a virtual COM I created.
Walt / WB4ZUT 




Re: Some Flex related questions

JoAnn Donaldson
 

If the software has a way to send UDF files, there is a Python Script that will intercept the UDF, forment it to work with N3FJP Logs, and send the formatted contact to ACLog.

JoAnn
AB8YZ

On Friday, January 8, 2021, 4:56:58 PM CST, W5IO <w5io@...> wrote:


I have been using Slice-Master in the past to start and connect CW Skimmer and WSJT to my Flex 6400. The software worked well and allowed CW Skimmers on both Slices. 

What if any connection with AC Log is possible with Slice Master or CW Skimmer? I don't see anything in the Help and groups.io does not mention Slice Master. CW Skimmer connection is not indicated from what I scanned in groups.io.

Trying to run WSJT via Slice Master didn't work. I seemed to be out of sequence or delayed somehow and got no response to my calls. This was while JTAlert was up with WSJT and JT alert was connected to ACLog. I am unsure how they all connect or if they should be all connected. 

Anyone with any experience trying to run Slice Master, CW Skimmer and ACLog? 

And, anyone try to run WSJT via Slice Mater and ACLog connected to JTAlert? 

Thanks

Maury
W5IO



Re: Found minor display bug in 6.8

Jim Shorney
 

I am seeing this on a Win7 Pro box that has not been updated recently.

73

-Jim (no lectures from the gallery, please)
NU0C

On Sat, 9 Jan 2021 20:56:27 +0000 (UTC)
"Scott Davis via groups.io" <SNKDavis=aol.com@groups.io> wrote:

Thanks for the report Paul.  I see that here as well.  I've not changed anything in the display, so Microsoft must have updated the behavior of the control in one of their updates.
Thanks again!

73, ScottN3FJPhttp://www.n3fjp.com
Serving the Amateur Radio community with contesting and general logging software since 1997.
1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...

-----Original Message-----
From: Paul AC9O <pphiliphome@gmail.com>
To: N3FJPSoftwareUsers@groups.io
Sent: Sat, Jan 9, 2021 1:44 pm
Subject: [N3FJPSoftwareUsers] Found minor display bug in 6.8

Hi Scott,

Just installed 6.8 a couple of days ago, thank you!.

I can re-create this display anomaly by editing an entry, don't have to change anything, then just click DONE.

The line being edited comes back black, not the original color (usually blue for confirmed). When I Clear to reset, the color comes back as expected.

Just a very minor thing but thought you would want to know about it.

Thanks, as always
73
Paul, AC9O





Re: Found minor display bug in 6.8

Scott Davis
 

Thanks for the report Paul.  I see that here as well.  I've not changed anything in the display, so Microsoft must have updated the behavior of the control in one of their updates.

Thanks again!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Paul AC9O <pphiliphome@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Sat, Jan 9, 2021 1:44 pm
Subject: [N3FJPSoftwareUsers] Found minor display bug in 6.8

Hi Scott,

Just installed 6.8 a couple of days ago, thank you!.

I can re-create this display anomaly by editing an entry, don't have to change anything, then just click DONE.

The line being edited comes back black, not the original color (usually blue for confirmed). When I Clear to reset, the color comes back as expected.

Just a very minor thing but thought you would want to know about it.

Thanks, as always
73
Paul, AC9O


Re: Found minor display bug in 6.8

Jim Shorney
 

I have noticed this as well. Not a big deal, no rush to fix it on my account. Stuff happens.

73

-Jim
NU0C

On Sat, 09 Jan 2021 10:44:03 -0800
"Paul AC9O" <pphiliphome@gmail.com> wrote:

Hi Scott,

Just installed 6.8 a couple of days ago, thank you!.

I can re-create this display anomaly by editing an entry, don't have to change anything, then just click DONE.

The line being edited comes back black, not the original color (usually blue for confirmed). When I Clear to reset, the color comes back as expected.

Just a very minor thing but thought you would want to know about it.

Thanks, as always
73
Paul, AC9O





locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Walter Egenmaier
 

Kevin,
It worked like a charm.
I'm adding in FLDIGI and then VARA FM next to see if I can get all of them "talking" on the same COM7.
Thanks for the help,
Walt/WB4ZUT


locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Michael WA7SKG
 

I have used VSPE for several years with good results. The biggest issue I have seen is incorrect configuration. Here's the step-by-step I use.

Open VSPE
Create New Device (Either click the icon with the connector and red star or Device > Create)
Under Device Type select Splitter, then NEXT
Under Virtual serial port select an unused port
Under Data source serial port select the physical serial port connected to your equipment (this can be determined in Device Manager)
Click Finish

Now go into the configuration for your various applications and point them to the virtual port you just created.

HTH,
Michael WA7SKG

Walter Egenmaier wrote on 1/9/21 10:39 AM:

I just d/l VSPE to add virtual ports so I can operate several softwares including my logger program N3FJP.
Are these 2 compatible? If so, why doesn't N3FJP see the rig when I put it on the COM7 I created from COM4?
Walt/WB4ZUT
_._,_._,_


locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Kevin Gray
 

 

Start VSPE

 

Click on Create New Device

Select device type: Splitter, click Next

Data Source Serial Port: COM4 (or whatever the radio serial port is for your radio) { Are you actually using a 991 ?  and picked the enhanced port to split ?}

Virtual Serial Port: COM7 (or whichever you want, make sure your logging programs use this port).

Click settings:

Speed: 57600 (or whatever your radio is currently using)

DTR/RTS: NO

Parity: no

Bits: 8

Stop bits: 1

Click OK

Redirect modem registers: CHECKED

Initial Modem Registers State: RTS: NOT CHECKED, DTR: NOT CHECKED

 

Once you’re all setup, click the Play button. VSPE should say that the initialization is OK.

 

Select the new port in ACLog, make sure all parameters are set, Baud, Parity, Data, Stop, etc

Then press the Test button on the rig interface form.

 

If this doesn’t work, send actual screen shots of what YOU have.

 

73

Kevin

N9VPV

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of Walter Egenmaier
Sent: Saturday, January 9, 2021 1:12 PM
To: N3FJPSoftwareUsers@groups.io
Subject: Re: [N3FJPSoftwareUsers] Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

 

Kevin, I used the following setup.
https://github.com/rfrht/FT991A-PAT/wiki/appendix-sharing-serial-port
Is that all you need?
I was successfully running on COM 4 and all I did was run VSPE and then open N3FJP and switched to COM 7 (which is a virtual COM I created.
Walt / WB4ZUT 


locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Walter Egenmaier
 

Kevin, I used the following setup.
https://github.com/rfrht/FT991A-PAT/wiki/appendix-sharing-serial-port
Is that all you need?
I was successfully running on COM 4 and all I did was run VSPE and then open N3FJP and switched to COM 7 (which is a virtual COM I created.
Walt / WB4ZUT 


locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Gary Woods
 

On Sat, 09 Jan 2021 10:39:19 -0800, you wrote:

I just d/l VSPE to add virtual ports so I can operate several softwares including my logger program N3FJP.
Are these 2 compatible? If so, why doesn't N3FJP see the rig when I put it on the COM7 I created from COM4?
Walt/WB4ZUT
Yes....I run VSPE 64-bit (refurb HP win7 box) with ACL, FlDigi, HDSR,
and occasionally WSJT-X all without a hickup. Just be consistant with
handshaking/baud rate etc.

--
Gary Woods O- K2AHC Public keys at home.earthlink.net/~garygarlic, or get 0x1D64A93D via keyserver
fingerprint = E2 6F 50 93 7B C7 F3 CA 1F 8B 3C C0 B0 28 68

--
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus


locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Kevin Gray
 

Walt,

I use Eterlogic VSPE always, and have for a very long time, and it works reliably and very well with ACLog in combination with many other applications. ACLog will see the port you create, and not know the difference between it and any real physical port.

 

If the settings you are using for that rig are correct, and have worked in the past, then the settings in VSPE are not right.

 

Since you haven’t included How you setup VSPE or any of the Settings for the port in VSPE, I’m afraid I can’t be of any more assistance.

If you can provide your settings from VSPE, I can try and help.

 

73

Kevin

N9VPV

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of Walter Egenmaier
Sent: Saturday, January 9, 2021 12:39
To: N3FJPSoftwareUsers@groups.io
Subject: [N3FJPSoftwareUsers] Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

 

I just d/l VSPE to add virtual ports so I can operate several softwares including my logger program N3FJP.
Are these 2 compatible? If so, why doesn't N3FJP see the rig when I put it on the COM7 I created from COM4?
Walt/WB4ZUT


locked Re: Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Walter Egenmaier
 

I should include I am using WIN10, and version 6.8 (newest) of N3FJP software. I d/l and installed the 32-bit version of Eterlogic's VSPE.


Found minor display bug in 6.8

Paul AC9O
 

Hi Scott,

Just installed 6.8 a couple of days ago, thank you!.

I can re-create this display anomaly by editing an entry, don't have to change anything, then just click DONE.

The line being edited comes back black, not the original color (usually blue for confirmed). When I Clear to reset, the color comes back as expected.

Just a very minor thing but thought you would want to know about it.

Thanks, as always
73
Paul, AC9O


locked Does N3FJP work with Eterlogic's VSPE software to expand single COM4 into virtual ports...if so how?

Walter Egenmaier
 

I just d/l VSPE to add virtual ports so I can operate several softwares including my logger program N3FJP.
Are these 2 compatible? If so, why doesn't N3FJP see the rig when I put it on the COM7 I created from COM4?
Walt/WB4ZUT


nc qso party

jim crisco WA4YIZ
 

hi scott...
i loaded acl 6-8...all went well...
then loaded nc qso party 3-2...
AVG wanted to scan it....
scan ran clean...
then install went without a hitch...

thanks for all the great software..

73
jim
wa4yiz


Re: 30 Meter pwr setup

Kevin Gray
 

Dave,

After you’re done with the bulk edit to record your power to the value you actually used.

Then try this, for future contacts :

In WSJT-X when you complete a contact, and the Log Window pops up, (either automatically or by pressing Log Contact, in WSJT-X {depending on your settings})

Fill-in the appropriate field for Power and Check the box to retain this setting, for any future contact. That should get you what you want, going forward.

 

 

73

Kevin

N9VPV

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of Scott Davis via groups.io
Sent: Saturday, January 9, 2021 6:30 AM
To: N3FJPSoftwareUsers@groups.io
Subject: Re: [N3FJPSoftwareUsers] 30 Meter pwr setup

 

Hi Dave,

 

Thanks for your e-mail.  It sounds like you need to do some bulk editing.  I've not ever tried it myself, but there have been lots of good reports on the group using ADIF Master for that sort of editing.

 

 

 

Enjoy!

73, Scott

N3FJP

 

Serving the Amateur Radio community with contesting and general logging software since 1997.

 

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...

 

-----Original Message-----
From: Dave Tucker Nu4N <dwtucker19@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Sat, Jan 9, 2021 6:56 am
Subject: [N3FJPSoftwareUsers] 30 Meter pwr setup

Hello Scott I am wanting to apply for the 30 MDG award for 30 qrp stations.
Is there a way to sent the power at 5 watts with out going thru manuely ?? The contacts that at not 5 w power came from the WSJT logging to ACLOG.
Thanks Dave NU4N

3981 - 4000 of 49913