1. N3FJPSoftwareUsers@groups.io
   Date   
Re: CQ WW

Larry Stowell K1ZW
 

Hey Scott

Thanks for the help BUT

I'm trying to fill out the 3830scores.com and the want zones and countries by band?

How do you get that from the stats?

73 Larry K1ZW

On 10/26/2020 4:49 PM, Scott Davis via groups.io wrote:
Hi Larry,

Thanks for your e-mail.  If you count off times greater than 30 minutes as being inactive, you operated 2:36:17.  If you count off times greater than 60 minutes as being inactive, you operated 4:07:37.

A quick check of the rules indicates 60 minutes for Class Overlay.  I didn't check to see if any of the other options had a time constraint.

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Larry Stowell K1ZW <wa2fif@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 4:39 pm
Subject: [N3FJPSoftwareUsers] CQ WW

I'm looking at the statistics an it has me confused(easy to do)

  Total op time (breaks > 30 min deducted): 2:36:17
 Total op time (breaks > 60 min deducted): 4:07:37

 Avg Qs/Hr (breaks > 30 min deducted): 39.5

What does this mean? How much operating time did I do?

73 Larry K1ZW
CQ WW D Contest Logger

JoAnn Donaldson
 

Scott,
    I know you have a reason for doing this but LOTW has a headache with it.
When the Contest was over, I had it not only create a Cabrillo log file which I
sent to CQ. I then had it make an .ADIF file. When I attempted to send this file
to LOTW, LOTW had a headache with it. Saying that the PH for Mode was Invalid.
I had to go back into the Contest Logger, create a new ADIF File but this time I let
it convert the PH to SSB. Then LOTW was happy. SO why do you use PH for SSB
contacts and not SSB? I did notice that the Field Day Logger used PHONE and LOTW
was Happy with that.

JoAnn
AB8YZ
Re: New log name

Donald R Beck
 

How do you get 24 hr time on the clocks?

DR Beck
Toolbox Productions,Inc.

On Oct 26, 2020, at 14:39, Dave via groups.io <kc3am@...> wrote:

 Thanks much Scott!
Just wanted to make sure I did not cause a problem.
Now to enter QSL cards from 1977 - 1984, log books no where to be found.

Dave KC3AM

On 10/26/2020 16:57, Scott Davis via groups.io wrote:
Hi Dave,

Thanks for your e-mail.  You can assign any valid Windows file name you like.  It is not used in any way, other than as the name of the log file.  You may want to click File > Save As and save your current log as KC3AM.mdb to minimize confusion, but that is entirely up to you.

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Dave via groups.io <kc3am@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 4:52 pm
Subject: [N3FJPSoftwareUsers] New log name

Hello everyone,

It is time for me to start  inputting data for my two previous call's
into ACL.

I see in the Faq section for multi ham families that all that is needed
is to do is
file > new > Start a new log with a new database .....

The existing log is called  LogData.mdb for my KC3AM call.

I wish to create a database for KC3AI and WB3GDB so would I name the new
file KC3AI.mdb  &  WB3GDB.mdb?

I don't want to cause myself any troubles.

Thanks much,
--
Hams should be seen as well as heard, 73, Dave KC3AM






--
Hams should be seen as well as heard, 73, Dave KC3AM
Re: New log name

Dave
 

Thanks much Scott!
Just wanted to make sure I did not cause a problem.
Now to enter QSL cards from 1977 - 1984, log books no where to be found.

Dave KC3AM

On 10/26/2020 16:57, Scott Davis via groups.io wrote:
Hi Dave,

Thanks for your e-mail.  You can assign any valid Windows file name you like.  It is not used in any way, other than as the name of the log file.  You may want to click File > Save As and save your current log as KC3AM.mdb to minimize confusion, but that is entirely up to you.

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Dave via groups.io <kc3am@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 4:52 pm
Subject: [N3FJPSoftwareUsers] New log name

Hello everyone,

It is time for me to start  inputting data for my two previous call's
into ACL.

I see in the Faq section for multi ham families that all that is needed
is to do is
file > new > Start a new log with a new database .....

The existing log is called  LogData.mdb for my KC3AM call.

I wish to create a database for KC3AI and WB3GDB so would I name the new
file KC3AI.mdb  &  WB3GDB.mdb?

I don't want to cause myself any troubles.

Thanks much,
--
Hams should be seen as well as heard, 73, Dave KC3AM






--
Hams should be seen as well as heard, 73, Dave KC3AM
Re: New log name

Dave
 

Thanks much Jim.
Dave KC3AM

On 10/26/2020 17:22, Jim Shorney wrote:
You can name it anything you want so long as it ends in .mdb.

73

-Jim
NU0C


On Mon, 26 Oct 2020 16:52:35 -0400
"Dave via groups.io" <kc3am=verizon.net@groups.io> wrote:

Hello everyone,

It is time for me to start  inputting data for my two previous call's
into ACL.

I see in the Faq section for multi ham families that all that is needed
is to do is
file > new > Start a new log with a new database .....

The existing log is called  LogData.mdb for my KC3AM call.

I wish to create a database for KC3AI and WB3GDB so would I name the new
file KC3AI.mdb  &  WB3GDB.mdb?

I don't want to cause myself any troubles.

Thanks much,


--
Hams should be seen as well as heard, 73, Dave KC3AM
Re: New log name

Jim Shorney
 

You can name it anything you want so long as it ends in .mdb.

73

-Jim
NU0C


On Mon, 26 Oct 2020 16:52:35 -0400
"Dave via groups.io" <kc3am=verizon.net@groups.io> wrote:

Hello everyone,

It is time for me to start  inputting data for my two previous call's
into ACL.

I see in the Faq section for multi ham families that all that is needed
is to do is
file > new > Start a new log with a new database .....

The existing log is called  LogData.mdb for my KC3AM call.

I wish to create a database for KC3AI and WB3GDB so would I name the new
file KC3AI.mdb  &  WB3GDB.mdb?

I don't want to cause myself any troubles.

Thanks much,
Re: New log name

Scott Davis
 

Hi Dave,

Thanks for your e-mail.  You can assign any valid Windows file name you like.  It is not used in any way, other than as the name of the log file.  You may want to click File > Save As and save your current log as KC3AM.mdb to minimize confusion, but that is entirely up to you.

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Dave via groups.io <kc3am@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 4:52 pm
Subject: [N3FJPSoftwareUsers] New log name

Hello everyone,

It is time for me to start  inputting data for my two previous call's
into ACL.

I see in the Faq section for multi ham families that all that is needed
is to do is
file > new > Start a new log with a new database .....

The existing log is called  LogData.mdb for my KC3AM call.

I wish to create a database for KC3AI and WB3GDB so would I name the new
file KC3AI.mdb  &  WB3GDB.mdb?

I don't want to cause myself any troubles.

Thanks much,
--
Hams should be seen as well as heard, 73, Dave KC3AM
New log name

Dave
 

Hello everyone,

It is time for me to start  inputting data for my two previous call's into ACL.

I see in the Faq section for multi ham families that all that is needed is to do is
file > new > Start a new log with a new database .....

The existing log is called  LogData.mdb for my KC3AM call.

I wish to create a database for KC3AI and WB3GDB so would I name the new file KC3AI.mdb  &  WB3GDB.mdb?

I don't want to cause myself any troubles.

Thanks much,
--
Hams should be seen as well as heard, 73, Dave KC3AM
Re: CQ WW

Scott Davis
 

Hi Larry,

Thanks for your e-mail.  If you count off times greater than 30 minutes as being inactive, you operated 2:36:17.  If you count off times greater than 60 minutes as being inactive, you operated 4:07:37.

A quick check of the rules indicates 60 minutes for Class Overlay.  I didn't check to see if any of the other options had a time constraint.

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Larry Stowell K1ZW <wa2fif@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 4:39 pm
Subject: [N3FJPSoftwareUsers] CQ WW

I'm looking at the statistics an it has me confused(easy to do)

  Total op time (breaks > 30 min deducted): 2:36:17
 Total op time (breaks > 60 min deducted): 4:07:37

 Avg Qs/Hr (breaks > 30 min deducted): 39.5

What does this mean? How much operating time did I do?

73 Larry K1ZW
CQ WW

Larry Stowell K1ZW
 

I'm looking at the statistics an it has me confused(easy to do)

  Total op time (breaks > 30 min deducted): 2:36:17
 Total op time (breaks > 60 min deducted): 4:07:37

 Avg Qs/Hr (breaks > 30 min deducted): 39.5

What does this mean? How much operating time did I do?

73 Larry K1ZW
Re: rig interface

Jeff KB6CA
 

I use Comm Port 3 for my Yaesu 1200.

 

Jeff KB6CA

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of Justin Lentz
Sent: October 26, 2020 11:22 AM
To: N3FJPSoftwareUsers@groups.io
Subject: Re: [N3FJPSoftwareUsers] rig interface

 

Are you sure that is the com port for the radio when installing the yaesu drivers

 

Justin Lentz KF5IVJ

Ellis County Amateur Radio Club President and Program Officer

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> on behalf of Donald R Beck <dbeck@...>
Sent: Monday, October 26, 2020 1:20:52 PM
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Subject: Re: [N3FJPSoftwareUsers] rig interface

 

Not working. I have a Yaesu 991a. Using com 1. Not polling. Would love to buy this program but it’s not seeing my rig and can’t get the Frequency to show in the fields

DR Beck

Toolbox Productions,Inc.



On Oct 26, 2020, at 03:21, Scott Davis via groups.io <SNKDavis@...> wrote:



Hi dbeck,

 

Thanks for your e-mail.  Frequency is recorded in all my contest software when rig interface is enabled.  To display the frequency column, press Ctrl + Shift + F.  More details are here:

 

 

 

 

Enjoy!

73, Scott

N3FJP

 

Serving the Amateur Radio community with contesting and general logging software since 1997.

 

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...

 

-----Original Message-----
From: dbeck@...
To: N3FJPSoftwareUsers@groups.io
Sent: Sun, Oct 25, 2020 10:35 pm
Subject: [N3FJPSoftwareUsers] rig interface

I dont see where this a column to automaticly enter the frequency for the contact worked.  Is this not a feature?  I dont see the column in the video or on the sample page

Re: using contest loggers to send CW

Scott Davis
 

Hi John,

Thanks for your e-mail.  Click Settings > Rig Interface and deselect the power option that is keying your cable (which sounds like is working fine).  

You will need to use a separate port for CW from rig interface.

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Frank MacKenzie-Lamb <maclamb@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 2:57 pm
Subject: Re: [N3FJPSoftwareUsers] using contest loggers to send CW

I had that happen also.......try DTS first and figure from there

Frank
NG1I

-----Original Message-----
From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of John Miller
Sent: Monday, October 26, 2020 2:40 PM
To: N3FJPSoftwareUsers@groups.io
Subject: [N3FJPSoftwareUsers] using contest loggers to send CW

I got a cable on amazon to go from the usb port of my computer and send CW with the straight key jack. I believe it uses RTS though there is no info with it. No matter how I set it though, as soon as I open the software, mostly tested with the 10 meter contest logger since that's the next contest I plan to participate in, as soon as I open the software it's like someone's holding a straight key down, just a constant tone. Is this a software setting I need to change or is it something with the cable? radio is a ts-590S not the G version. I have another cable with the 1/4 jack I tried that with an adapter but the computer doesn't like that one, it will this computer just is a pain about anything I add to it for some reason and I don't feel like going through the hassle of setting up another device on this nightmare computer if I don't have to. I'm guessing there is no way to send CW with the usb port in the radio as there is with some? I rather send by hand but you know the odd contest now and then it's nice to have that for stored CW reports and stuff.
Thanks,
Re: using contest loggers to send CW

Frank MacKenzie-Lamb
 

I had that happen also.......try DTS first and figure from there

Frank
NG1I

-----Original Message-----
From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of John Miller
Sent: Monday, October 26, 2020 2:40 PM
To: N3FJPSoftwareUsers@groups.io
Subject: [N3FJPSoftwareUsers] using contest loggers to send CW

I got a cable on amazon to go from the usb port of my computer and send CW with the straight key jack. I believe it uses RTS though there is no info with it. No matter how I set it though, as soon as I open the software, mostly tested with the 10 meter contest logger since that's the next contest I plan to participate in, as soon as I open the software it's like someone's holding a straight key down, just a constant tone. Is this a software setting I need to change or is it something with the cable? radio is a ts-590S not the G version. I have another cable with the 1/4 jack I tried that with an adapter but the computer doesn't like that one, it will this computer just is a pain about anything I add to it for some reason and I don't feel like going through the hassle of setting up another device on this nightmare computer if I don't have to. I'm guessing there is no way to send CW with the usb port in the radio as there is with some? I rather send by hand but you know the odd contest now and then it's nice to have that for stored CW reports and stuff.
Thanks,
using contest loggers to send CW

John Miller
 

I got a cable on amazon to go from the usb port of my computer and
send CW with the straight key jack. I believe it uses RTS though there
is no info with it. No matter how I set it though, as soon as I open
the software, mostly tested with the 10 meter contest logger since
that's the next contest I plan to participate in, as soon as I open
the software it's like someone's holding a straight key down, just a
constant tone. Is this a software setting I need to change or is it
something with the cable? radio is a ts-590S not the G version. I have
another cable with the 1/4 jack I tried that with an adapter but the
computer doesn't like that one, it will this computer just is a pain
about anything I add to it for some reason and I don't feel like going
through the hassle of setting up another device on this nightmare
computer if I don't have to. I'm guessing there is no way to send CW
with the usb port in the radio as there is with some? I rather send by
hand but you know the odd contest now and then it's nice to have that
for stored CW reports and stuff.
Thanks,
Re: rig interface

Scott Davis
 

Hi DR,

Thanks for your follow up.  I don't have any Yaesu equipment here myself, but you will find the successful settings other 991 users have sent along here:

http://www.n3fjp.com/help/righelp.html

Thanks for your interest in my software!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Donald R Beck <dbeck@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 2:20 pm
Subject: Re: [N3FJPSoftwareUsers] rig interface

Not working. I have a Yaesu 991a. Using com 1. Not polling. Would love to buy this program but it’s not seeing my rig and can’t get the Frequency to show in the fields

DR Beck
Toolbox Productions,Inc.

On Oct 26, 2020, at 03:21, Scott Davis via groups.io <SNKDavis@...> wrote:


Hi dbeck,

Thanks for your e-mail.  Frequency is recorded in all my contest software when rig interface is enabled.  To display the frequency column, press Ctrl + Shift + F.  More details are here:


http://www.n3fjp.com/faq.html#q74


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: dbeck@...
To: N3FJPSoftwareUsers@groups.io
Sent: Sun, Oct 25, 2020 10:35 pm
Subject: [N3FJPSoftwareUsers] rig interface

I dont see where this a column to automaticly enter the frequency for the contact worked.  Is this not a feature?  I dont see the column in the video or on the sample page

Re: new user-lotw confirmations?

Donald R Beck
 

What I want to do is have a column under “recent contact” that displays frequency. And not have it on the lower box. How?

DR Beck
Toolbox Productions,Inc.

On Oct 26, 2020, at 09:13, Scott Davis via groups.io <SNKDavis@...> wrote:


Thanks for the good report Ken.  Sometimes, when the LoTW server is busy, it won't return very large data requests, so you might give it another try after the contest dust has settled.

Thanks for your support!

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Ken Reid <khz3895@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 12:10 pm
Subject: Re: [N3FJPSoftwareUsers] new user-lotw confirmations?

Hi Scott,
Thanks for the quick reply.
Yes that worked.
I confirmed everything in 2020
I tried it earlier at got a server not responding notice.
Ill try again from the beginning later.
Once I get it all in and confirmed Ill get a license.
BTW- Mike Montrose KA2JAI recommended the program to me.
I am a N1MM user for contests
73
Ken

On Mon, Oct 26, 2020 at 12:01 PM Scott Davis via groups.io <SNKDavis=aol.com@groups.io> wrote:
Hi Ken,

Thanks for your e-mail.  Yes, on AC Log's LoTW form, click the button under the Download heading that says All Data.

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Ken Reid <khz3895@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 11:20 am
Subject: [N3FJPSoftwareUsers] new user-lotw confirmations?

Hi,
I brought in all my previous logs (Maclogger) via adi.
It does not seem like any of the qsls sent or confirmed came along.
In Maclogger I would download a adi file from lbotw, and use that to confirm contacts.
I have LBOTW working on my PC, and I think its all working on the new logging program.
Is there a way to confirm all my contacts ? I have downloaded a adi from Lbotw with all my confirmations, or is there a way to go direct.
Cross posted to both groups
Thanks
73
Ken
KG4USN


--
Ken Reid

311 Martins Cove Rd
Annapolis MD 21409
305-301-4503
Re: rig interface

Justin Lentz KF5IVJ
 

Are you sure that is the com port for the radio when installing the yaesu drivers

Justin Lentz KF5IVJ
Ellis County Amateur Radio Club President and Program Officer

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> on behalf of Donald R Beck <dbeck@...>
Sent: Monday, October 26, 2020 1:20:52 PM
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Subject: Re: [N3FJPSoftwareUsers] rig interface
 
Not working. I have a Yaesu 991a. Using com 1. Not polling. Would love to buy this program but it’s not seeing my rig and can’t get the Frequency to show in the fields

DR Beck
Toolbox Productions,Inc.

On Oct 26, 2020, at 03:21, Scott Davis via groups.io <SNKDavis@...> wrote:


Hi dbeck,

Thanks for your e-mail.  Frequency is recorded in all my contest software when rig interface is enabled.  To display the frequency column, press Ctrl + Shift + F.  More details are here:


http://www.n3fjp.com/faq.html#q74


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: dbeck@...
To: N3FJPSoftwareUsers@groups.io
Sent: Sun, Oct 25, 2020 10:35 pm
Subject: [N3FJPSoftwareUsers] rig interface

I dont see where this a column to automaticly enter the frequency for the contact worked.  Is this not a feature?  I dont see the column in the video or on the sample page

Re: rig interface

Donald R Beck
 

Not working. I have a Yaesu 991a. Using com 1. Not polling. Would love to buy this program but it’s not seeing my rig and can’t get the Frequency to show in the fields

DR Beck
Toolbox Productions,Inc.

On Oct 26, 2020, at 03:21, Scott Davis via groups.io <SNKDavis@...> wrote:


Hi dbeck,

Thanks for your e-mail.  Frequency is recorded in all my contest software when rig interface is enabled.  To display the frequency column, press Ctrl + Shift + F.  More details are here:


http://www.n3fjp.com/faq.html#q74


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: dbeck@...
To: N3FJPSoftwareUsers@groups.io
Sent: Sun, Oct 25, 2020 10:35 pm
Subject: [N3FJPSoftwareUsers] rig interface

I dont see where this a column to automaticly enter the frequency for the contact worked.  Is this not a feature?  I dont see the column in the video or on the sample page

Re: Parks on the Air (POTA) logging

Richard Rohrer
 

Hi Jim,

How does it do that?  Do you have to change your location in ACL?  I run mobile/portable a lot and use the method described above setting up a new LOTW location.  This seems easier.

73
Dick - KC3EF
Re: new user-lotw confirmations?

Scott Davis
 

Thanks for the good report Ken.  Sometimes, when the LoTW server is busy, it won't return very large data requests, so you might give it another try after the contest dust has settled.

Thanks for your support!

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Ken Reid <khz3895@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 12:10 pm
Subject: Re: [N3FJPSoftwareUsers] new user-lotw confirmations?

Hi Scott,
Thanks for the quick reply.
Yes that worked.
I confirmed everything in 2020
I tried it earlier at got a server not responding notice.
Ill try again from the beginning later.
Once I get it all in and confirmed Ill get a license.
BTW- Mike Montrose KA2JAI recommended the program to me.
I am a N1MM user for contests
73
Ken

On Mon, Oct 26, 2020 at 12:01 PM Scott Davis via groups.io <SNKDavis=aol.com@groups.io> wrote:
Hi Ken,

Thanks for your e-mail.  Yes, on AC Log's LoTW form, click the button under the Download heading that says All Data.

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Ken Reid <khz3895@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Mon, Oct 26, 2020 11:20 am
Subject: [N3FJPSoftwareUsers] new user-lotw confirmations?

Hi,
I brought in all my previous logs (Maclogger) via adi.
It does not seem like any of the qsls sent or confirmed came along.
In Maclogger I would download a adi file from lbotw, and use that to confirm contacts.
I have LBOTW working on my PC, and I think its all working on the new logging program.
Is there a way to confirm all my contacts ? I have downloaded a adi from Lbotw with all my confirmations, or is there a way to go direct.
Cross posted to both groups
Thanks
73
Ken
KG4USN


--
Ken Reid

311 Martins Cove Rd
Annapolis MD 21409
305-301-4503
2641 - 2660 of 47091