1. N3FJPSoftwareUsers@groups.io
   Date   
Re: WinkeyerUSB

AI3KS
 

Ron,

Sounds like it might be RF. Have you tried using lower power? I know that I get all kinds of wierd things when I run rtty at more than about 40 watts on 15 meters.

Steve, AI3KS

On 20/10/04 17:29, k6jta@... wrote:
I just purchased a Winkeyer.  Have it configured OK.  In CalQSO I clicked on Winkeryer in CW setup.  Keyer works ok for about half and hour, then I get a message that Access To Com1 is denied.  Go back into WinTools and
it shows as Com3.  Go through setup again.  Keyer works for about a half hour or less, the Access To Com1 is denied.
What am I doing wrong.
Thanks, Ron, K6JTA

Re: WinkeyerUSB

Frank MacKenzie-Lamb
 

Hi Ron,

 

Perhaps my documentation may help you. Please let me know

 

Frank

NG1I

 

 

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of k6jta@...
Sent: Sunday, October 4, 2020 5:30 PM
To: N3FJPSoftwareUsers@groups.io
Subject: [N3FJPSoftwareUsers] WinkeyerUSB

 

I just purchased a Winkeyer.  Have it configured OK.  In CalQSO I clicked on Winkeryer in CW setup.  Keyer works ok for about half and hour, then I get a message that Access To Com1 is denied.  Go back into WinTools and
it shows as Com3.  Go through setup again.  Keyer works for about a half hour or less, the Access To Com1 is denied.
What am I doing wrong.
Thanks, Ron, K6JTA

PDF
Setting Up Winkeyer.pdf
PDF
Setting Up Winkeyer 7300.pdf

WinkeyerUSB

k6jta@...
 

I just purchased a Winkeyer.  Have it configured OK.  In CalQSO I clicked on Winkeryer in CW setup.  Keyer works ok for about half and hour, then I get a message that Access To Com1 is denied.  Go back into WinTools and
it shows as Com3.  Go through setup again.  Keyer works for about a half hour or less, the Access To Com1 is denied.
What am I doing wrong.
Thanks, Ron, K6JTA
A 'universal' contest logger

Bo W4GHV
 

The  Worked All Europe program works fine for those requiring a serial number. seltect Generic Contest in fldigi and set the macros correctly and it does great.
Using on the Russian RTTY contest now, but the conditions aren't that good here.
--
73, Bo W4GHV since '54
https://www.qrz.com/db/W4GHV
Re: CAQP software

Joseph Miller
 

Thank you Steve. This is not a rule that I am not accustomed to for in-state operation, and I don't like it either. But the rules are the rules.

Thanks again and good luck,

73 de Joe KJ8O


On Sat, Oct 3, 2020 at 10:37 AM AI3KS <AI3KS.01@...> wrote:
Joe,

From the rules page:

"MULTIPLIERS:
A. California Stations (Maximum of 58 Multipliers)
Count U.S. states (50) and Canadian areas (8): MR, QC, ON, MB, SK, AB, BC and NT where:
  • MR = Maritime provinces plus Newfoundland and Labrador (NB, NL, NS, PE)
  • NT = Northern Territories (NT, NU, YT)

Note: Although the “CA” abbreviation is not used as a multiplier in this contest, the first valid CA county logged will count as the multiplier for California.  California stations must log all CA contacts with their 4-letter county abbreviation; everything else as two characters, including "DX" for all stations outside of the U.S. and Canada."

If I am reading this correctly, it looks like CA stations only count for QSO points for in-state stations, so the calculation is correct.

Steve, AI3KS


On 20/10/03 13:23, Joseph Miller wrote:
Hello Scott,

Maybe I messed up somewhere but I am using the in-state version of the Cal QSO Party software.

As I send this, I have contacts in 4 states and 6 counties and 10 contacts. My score shows as 80 (20 QSO points X 4 states). Shouldn't it read 200 (20 QSO points X 10 states and counties)?

Just wondering.

73 de Joe Miller KJ8O/W6 since 2018



--
***  Avoid internet congestion, real radio uses airwaves.  ***

Joe Miller, KJ8O
Desert Hot Springs, CA
Locator DM13sw
Re: CAQP software

AI3KS
 

Joe,

From the rules page:

"MULTIPLIERS:
A. California Stations (Maximum of 58 Multipliers)
Count U.S. states (50) and Canadian areas (8): MR, QC, ON, MB, SK, AB, BC and NT where:
  • MR = Maritime provinces plus Newfoundland and Labrador (NB, NL, NS, PE)
  • NT = Northern Territories (NT, NU, YT)

Note: Although the “CA” abbreviation is not used as a multiplier in this contest, the first valid CA county logged will count as the multiplier for California.  California stations must log all CA contacts with their 4-letter county abbreviation; everything else as two characters, including "DX" for all stations outside of the U.S. and Canada."

If I am reading this correctly, it looks like CA stations only count for QSO points for in-state stations, so the calculation is correct.

Steve, AI3KS


On 20/10/03 13:23, Joseph Miller wrote:
Hello Scott,

Maybe I messed up somewhere but I am using the in-state version of the Cal QSO Party software.

As I send this, I have contacts in 4 states and 6 counties and 10 contacts. My score shows as 80 (20 QSO points X 4 states). Shouldn't it read 200 (20 QSO points X 10 states and counties)?

Just wondering.

73 de Joe Miller KJ8O/W6 since 2018
CAQP software

Joseph Miller
 

Hello Scott,

Maybe I messed up somewhere but I am using the in-state version of the Cal QSO Party software.

As I send this, I have contacts in 4 states and 6 counties and 10 contacts. My score shows as 80 (20 QSO points X 4 states). Shouldn't it read 200 (20 QSO points X 10 states and counties)?

Just wondering.

73 de Joe Miller KJ8O/W6 since 2018
Issues with Editing Fields Displayed, etc..

James Goff
 

I am pleased to report with Thanks to Forum users, I have been able to correct the problem. The main form file was, apparently, corrupted...my first clue should have been its displaced "Comments" field location-- askew in the middle of the entry form.

After exporting the ADIF data and reloading ACLog, the form look as it should;  importing ADIF data brought all previous QSOs back, perfectly.

Thanks to all,

73, W1JHG

-- 
-Jim

James H. Goff
207-944-3297 (c)
 
Re: CA QSO PARTY LOG

Scott Davis
 

Hi Tim,

Thanks for your e-mail.  Enter all 3 counties (from the main form, click Change County and then click the button).

Enjoy!


73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Tim Thorson <kd6hof@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Sat, Oct 3, 2020 1:19 am
Subject: Re: [N3FJPSoftwareUsers] CA QSO PARTY LOG

I will be running at a triple County station to operate the California QSO Party. 

When I set up my logging software, when asked for my County, do I just pick any one of the 3? Will this be a problem when I submit logs?

As I understand it, I would just instruct the stations to simply log me three separate times with each county (unless their SW can log it in one entry). 

I assume This software will allow it (with warning??)

73, Tim  KD6HOF



On Fri, Oct 2, 2020 at 3:21 PM Joseph Miller <kj8o.ham@...> wrote:
Hi Ray,

I will be working it too. Just did a test spin, and the Cabrill file correctly reports the 4 letter county abbreviations, as shown below,

START-OF-LOG: 3.0
CREATED-BY: N3FJP's California QSO Party Contest Log 4.2
CONTEST: NCCC-CQP
CALLSIGN: KJ8O
LOCATION: CA
CATEGORY-OPERATOR: KJ8O
CATEGORY-STATION: FIXED
CATEGORY-TRANSMITTER: ONE
CATEGORY-POWER: LOW
CATEGORY-ASSISTED: NON-ASSISTED
CATEGORY-BAND: ALL
CATEGORY-MODE: SSB
CATEGORY-TIME: 12-HOURS
CLAIMED-SCORE: 2
OPERATORS: KJ8O
NAME: Joseph Miller
ADDRESS: 67625 Monterey Road
ADDRESS-CITY: Desert Hot Springs
ADDRESS-STATE-PROVINCE: CA
ADDRESS-POSTALCODE: 92240
ADDRESS-COUNTRY: U.S.A.
EMAIL: kj8o.ham@...
QSO:  7000 PH 2020-10-02 2208 KJ8O        001 RIVE N6HE        001 LANG
END-OF-LOG:

Hope this answers your question.

vy 73 de Joe KJ8O

On Fri, Oct 2, 2020 at 2:59 PM Ray Day N6HE <rayday@...> wrote:
Hi all,
I'll be in the CA QSO Party this w/e - i notice that clicking on the CA CNTY in the list populates the CNTY field with, e.g., "Los Angeles" and not the prescribed cnty abbrev "LANG", as the rules say to send. Will this be accepted by the sponsors / has anybody submitted in the past the full cnty spelled out and not the 4-character abbreviation and had it accepted OK?
Thanks,
Ray N6HE


--
***  Avoid internet congestion, real radio uses airwaves.  ***

Joe Miller, KJ8O
Desert Hot Springs, CA
Locator DM13sw
Re: CA QSO PARTY LOG

K8TS
 

Tim;

How do we know you are in 3 counties in one transmission without you doing a “laundry list” in each transmission?  This question really belongs on a different thread than Scott’s, but actually presents some logging problems with us out-of-staters. How can you be in three counties at once?

Dale K8TS

 

Sent from Mail for Windows 10

 

From: Tim Thorson
Sent: Saturday, October 3, 2020 1:19 AM
To: N3FJPSoftwareUsers@groups.io
Subject: Re: [N3FJPSoftwareUsers] CA QSO PARTY LOG

 

I will be running at a triple County station to operate the California QSO Party. 

 

When I set up my logging software, when asked for my County, do I just pick any one of the 3? Will this be a problem when I submit logs?

 

As I understand it, I would just instruct the stations to simply log me three separate times with each county (unless their SW can log it in one entry). 

 

I assume This software will allow it (with warning??)

 

73, Tim  KD6HOF

 

 

 

On Fri, Oct 2, 2020 at 3:21 PM Joseph Miller <kj8o.ham@...> wrote:

Hi Ray,

 

I will be working it too. Just did a test spin, and the Cabrill file correctly reports the 4 letter county abbreviations, as shown below,

 

START-OF-LOG: 3.0

CREATED-BY: N3FJP's California QSO Party Contest Log 4.2

CONTEST: NCCC-CQP

CALLSIGN: KJ8O

LOCATION: CA

CATEGORY-OPERATOR: KJ8O

CATEGORY-STATION: FIXED

CATEGORY-TRANSMITTER: ONE

CATEGORY-POWER: LOW

CATEGORY-ASSISTED: NON-ASSISTED

CATEGORY-BAND: ALL

CATEGORY-MODE: SSB

CATEGORY-TIME: 12-HOURS

CLAIMED-SCORE: 2

OPERATORS: KJ8O

NAME: Joseph Miller

ADDRESS: 67625 Monterey Road

ADDRESS-CITY: Desert Hot Springs

ADDRESS-STATE-PROVINCE: CA

ADDRESS-POSTALCODE: 92240

ADDRESS-COUNTRY: U.S.A.

QSO:  7000 PH 2020-10-02 2208 KJ8O        001 RIVE N6HE        001 LANG

END-OF-LOG:

 

Hope this answers your question.

 

vy 73 de Joe KJ8O

 

On Fri, Oct 2, 2020 at 2:59 PM Ray Day N6HE <rayday@...> wrote:

Hi all,
I'll be in the CA QSO Party this w/e - i notice that clicking on the CA CNTY in the list populates the CNTY field with, e.g., "Los Angeles" and not the prescribed cnty abbrev "LANG", as the rules say to send. Will this be accepted by the sponsors / has anybody submitted in the past the full cnty spelled out and not the 4-character abbreviation and had it accepted OK?
Thanks,
Ray N6HE


 

--

***  Avoid internet congestion, real radio uses airwaves.  ***

 

Joe Miller, KJ8O

Desert Hot Springs, CA

Locator DM13sw

 
Re: CA QSO PARTY LOG

Tim Thorson
 

I will be running at a triple County station to operate the California QSO Party. 

When I set up my logging software, when asked for my County, do I just pick any one of the 3? Will this be a problem when I submit logs?

As I understand it, I would just instruct the stations to simply log me three separate times with each county (unless their SW can log it in one entry). 

I assume This software will allow it (with warning??)

73, Tim  KD6HOF



On Fri, Oct 2, 2020 at 3:21 PM Joseph Miller <kj8o.ham@...> wrote:
Hi Ray,

I will be working it too. Just did a test spin, and the Cabrill file correctly reports the 4 letter county abbreviations, as shown below,

START-OF-LOG: 3.0
CREATED-BY: N3FJP's California QSO Party Contest Log 4.2
CONTEST: NCCC-CQP
CALLSIGN: KJ8O
LOCATION: CA
CATEGORY-OPERATOR: KJ8O
CATEGORY-STATION: FIXED
CATEGORY-TRANSMITTER: ONE
CATEGORY-POWER: LOW
CATEGORY-ASSISTED: NON-ASSISTED
CATEGORY-BAND: ALL
CATEGORY-MODE: SSB
CATEGORY-TIME: 12-HOURS
CLAIMED-SCORE: 2
OPERATORS: KJ8O
NAME: Joseph Miller
ADDRESS: 67625 Monterey Road
ADDRESS-CITY: Desert Hot Springs
ADDRESS-STATE-PROVINCE: CA
ADDRESS-POSTALCODE: 92240
ADDRESS-COUNTRY: U.S.A.
EMAIL: kj8o.ham@...
QSO:  7000 PH 2020-10-02 2208 KJ8O        001 RIVE N6HE        001 LANG
END-OF-LOG:

Hope this answers your question.

vy 73 de Joe KJ8O

On Fri, Oct 2, 2020 at 2:59 PM Ray Day N6HE <rayday@...> wrote:
Hi all,
I'll be in the CA QSO Party this w/e - i notice that clicking on the CA CNTY in the list populates the CNTY field with, e.g., "Los Angeles" and not the prescribed cnty abbrev "LANG", as the rules say to send. Will this be accepted by the sponsors / has anybody submitted in the past the full cnty spelled out and not the 4-character abbreviation and had it accepted OK?
Thanks,
Ray N6HE



--
***  Avoid internet congestion, real radio uses airwaves.  ***

Joe Miller, KJ8O
Desert Hot Springs, CA
Locator DM13sw
Re: CA QSO PARTY LOG

Joseph Miller
 

Hi Ray,

I will be working it too. Just did a test spin, and the Cabrill file correctly reports the 4 letter county abbreviations, as shown below,

START-OF-LOG: 3.0
CREATED-BY: N3FJP's California QSO Party Contest Log 4.2
CONTEST: NCCC-CQP
CALLSIGN: KJ8O
LOCATION: CA
CATEGORY-OPERATOR: KJ8O
CATEGORY-STATION: FIXED
CATEGORY-TRANSMITTER: ONE
CATEGORY-POWER: LOW
CATEGORY-ASSISTED: NON-ASSISTED
CATEGORY-BAND: ALL
CATEGORY-MODE: SSB
CATEGORY-TIME: 12-HOURS
CLAIMED-SCORE: 2
OPERATORS: KJ8O
NAME: Joseph Miller
ADDRESS: 67625 Monterey Road
ADDRESS-CITY: Desert Hot Springs
ADDRESS-STATE-PROVINCE: CA
ADDRESS-POSTALCODE: 92240
ADDRESS-COUNTRY: U.S.A.
EMAIL: kj8o.ham@...
QSO:  7000 PH 2020-10-02 2208 KJ8O        001 RIVE N6HE        001 LANG
END-OF-LOG:

Hope this answers your question.

vy 73 de Joe KJ8O

On Fri, Oct 2, 2020 at 2:59 PM Ray Day N6HE <rayday@...> wrote:
Hi all,
I'll be in the CA QSO Party this w/e - i notice that clicking on the CA CNTY in the list populates the CNTY field with, e.g., "Los Angeles" and not the prescribed cnty abbrev "LANG", as the rules say to send. Will this be accepted by the sponsors / has anybody submitted in the past the full cnty spelled out and not the 4-character abbreviation and had it accepted OK?
Thanks,
Ray N6HE



--
***  Avoid internet congestion, real radio uses airwaves.  ***

Joe Miller, KJ8O
Desert Hot Springs, CA
Locator DM13sw
CA QSO PARTY LOG

Ray Day N6HE
 

Hi all,
I'll be in the CA QSO Party this w/e - i notice that clicking on the CA CNTY in the list populates the CNTY field with, e.g., "Los Angeles" and not the prescribed cnty abbrev "LANG", as the rules say to send. Will this be accepted by the sponsors / has anybody submitted in the past the full cnty spelled out and not the 4-character abbreviation and had it accepted OK?
Thanks,
Ray N6HE
Re: Portabke Operations Challenge Log

Scott Davis
 

Hi Catherine,

Thanks for your e-mail.  Given the complexity of the scoring for this contest, lack of similar template to build from and very late announcement notice, I'm not going to be able to support it this year.  The steering committee also indicated that they may make adjustments to the scoring after reviewing the first year.  


http://www.n3fjp.com/faq.html#q123

I'm sorry that I didn't have the answer you were looking for this time, but depending on how the event progresses in the next year or two, I am definitely keeping a close eye for possible future inclusion.

Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Catherine AC4YL <hamac4yl@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Fri, Oct 2, 2020 2:58 pm
Subject: [N3FJPSoftwareUsers] Portabke Operations Challenge Log

Good day all,

Thus is Catherine AC4YL.  I’m very much looking forward to participating in the portable operations  challenge this weekend.  The exchange is callsign, station class (Q or P), serial number, and 4 character grid square.  Callsigns, frequency, date snd time in UTC, and power must also be recorded.

I’d like to use N3FJP for logging.  I’m guessing the only log to use would be AC log?  I was just wondering if there were any plans to create a log for this event with the exchange boxes without score calculations (cause their scoring is a bit of a convoluted mess)?  I love the contest logs as they make keeping up with the exchanges much easier as that’s the only info on the screen.

https://www.foxmikehotel.com/challenge

Thanks and 73,
Catherine AC4YL

Portabke Operations Challenge Log

Catherine AC4YL
 

Good day all,

Thus is Catherine AC4YL.  I’m very much looking forward to participating in the portable operations  challenge this weekend.  The exchange is callsign, station class (Q or P), serial number, and 4 character grid square.  Callsigns, frequency, date snd time in UTC, and power must also be recorded.

I’d like to use N3FJP for logging.  I’m guessing the only log to use would be AC log?  I was just wondering if there were any plans to create a log for this event with the exchange boxes without score calculations (cause their scoring is a bit of a convoluted mess)?  I love the contest logs as they make keeping up with the exchanges much easier as that’s the only info on the screen.

https://www.foxmikehotel.com/challenge

Thanks and 73,
Catherine AC4YL
locked Re: Is there a way?

John AJ1R
 

This thread was started by mistake.  I posted a message here that should have been in the ICOM 7610 area.
I have deleted my original posting but can not find a way to delete or close the complete thread.
Re: CW transmit of rig's stored message memories

Scott Davis
 

Thanks for the great report Ray.  If you can put together some quick documentation along the lines of what Jim did here, that would be super!

http://www.n3fjp.com/help/CWRIK2.pdf

Thanks again!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Ray Dabkowski <w8rd@...>
To: N3FJPSoftwareUsers@groups.io
Sent: Fri, Oct 2, 2020 2:27 pm
Subject: Re: [N3FJPSoftwareUsers] CW transmit of rig's stored message memories

Hey Scott,

Actually, Jim suggested concatenating the commands, and I couldn't get it to work. And just now, I tried it again and it's flying! Pressing one F key builds the exchange in the memory slot, and then sends that slot off to the radio's keyer. Not sure what changed (maybe baud rate? cpu load? who knows). Bottom line: we have a winner! 

This scheme will probably work for quite a few Yaesu rigs (also FT-991, FT-2000, FT-3000, since they have the same CAT command set).

Jim if you're seeing this, thanks for your ideas.

73,
Ray W8RD

N3FJP Country Files - 02 October 2020

Jim Reisert AD1C
 

There are new country files for ACLog and related software by N3FJP.

To update the country files from the logging program menu, select:

Files -> Download Country Files From AD1C

You should download all three files. When done, you can re-start your
logging program.

Manual installation instructions are here:

https://www.country-files.com/n3fjp-info/

Here are the release notes:

https://www.country-files.com/n3fjp-02-october-2020/

N3FJP - 2 October 2020
Version entity is Cyprus, 5B

Added/changed Entities/Prefixes/Callsigns:

* 4U75A is Vienna Intl Ctr, *4U1V
* IT9ACJ/I/BO is Sicily, *IT9
* 4U75UN is United Nations HQ, 4U1U
* 2E0CVN/NHS is England, G
* IQ3MV/LH is Italy, I
* AL4F is in ITU zone 6, not ITU zone 7
* AL4F is in CQ zone 3, not CQ zone 4
* KH7TG, KL0TQ, KL7SV, NH7DZ, NP2LK, WH7TY and WL7AXI are all United States, K in CQ zone 3, ITU zone 6
* KH2EV and KL7BOB are both United States, K in CQ zone 4, ITU zone 7
* KL7TN/P is United States, K in CQ zone 4, ITU zone 8
* KP3FT, KP4MMG, KP4RMM, WP4IVW and WP4JNB are all United States, K in CQ zone 5, ITU zone 8
* K7CMK, KE6QQ, KJ6PEH and W0OHO are all Hawaii, KH6
* AI7CF, K0ESQ, KD6NFV, N4DBX, NN5H and W5AIT are all Alaska, KL
* KB1JMX is Puerto Rico, KP4
* 4U75A is Austria, OE
* R925RZ is European Russia, UA
* UA9CSA/1 is European Russia, UA in ITU zone 19

Removed Entities/Prefixes/Callsigns:

* GB80BOB in Northern Ireland, GI
* KH6ARA in United States, K
* K0LUC in Hawaii, KH6

If you have any questions, send E-mail to Jim Reisert AD1C (at the
address below) or make a post to the N3FJP software users reflector.

73 - Jim AD1C

--
Jim Reisert AD1C, <jjreisert at alum.mit.edu>, https://www.ad1c.us
Re: CW transmit of rig's stored message memories

Ray Dabkowski
 

Hey Scott,

Actually, Jim suggested concatenating the commands, and I couldn't get it to work. And just now, I tried it again and it's flying! Pressing one F key builds the exchange in the memory slot, and then sends that slot off to the radio's keyer. Not sure what changed (maybe baud rate? cpu load? who knows). Bottom line: we have a winner! 

This scheme will probably work for quite a few Yaesu rigs (also FT-991, FT-2000, FT-3000, since they have the same CAT command set).

Jim if you're seeing this, thanks for your ideas.

73,
Ray W8RD
locked Re: Is there a way?

Pat Whelton
 

Hey John.  Where exactly is this feature located in ACLog?  I’ve never seen it.

 

Regards,

 

Pat – KZ5J

 

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> On Behalf Of John AJ1R
Sent: Friday, October 2, 2020 7:39 AM
To: N3FJPSoftwareUsers@groups.io
Subject: [N3FJPSoftwareUsers] Is there a way?

 

I would like to be able to store three types of frequencies for easy recall.
1 - Temporary frequencies of recently heard stations that I may call
2 - Frequencies of nets that I regularly check into
3 - Frequencies like start of SSB segments for various  bands like fpr 40,20,15 meters

I can use the 5/10 temporary memories for ether #1 or #2
The standard memories could be used for #2 and #3.
However, recall access to standard memories is difficult because of the small size of the knob.
Especially for me due to limited ability to turn it due to physical limitations of my dominate hand.
Due to diabetes the fingers on it have been "shortened".

For example a second set of temporary  memories if available would really help.

Any ideas or suggestions would be appreciated, thanks.

_._,_._,_
2081 - 2100 of 46164  
More
Home Messages Hashtags About Features Pricing Updates Terms Help Twitter