Date   
Re: Not Sending CW with Elecraft

k1oj <k1oj@...>
 

I covered the same territory.  Ended up using  a winkeyer. Pro is that you can easily run different logging softwares with no hardware or keyed configuration changes. Con is you have to be running software to operate unless you move a key directly to the rig and change key menu to correct setting...
De k1oj

-------- Original message --------
From: Jim K9TF <jim.gmforum@...>
Date: 3/8/20 11:14 AM (GMT-06:00)
To: N3FJPSoftwareUsers@groups.io
Subject: Re: [N3FJPSoftwareUsers] Not Sending CW with Elecraft

The more I look into this, even I do not want to, is to use K1EL Winkeyer box. Or some sort of virtual com port software that works with N3FJP software. Some one suggested to use  LP Bridge   Ihttp://www.telepostinc.com/LPB.html have no Idea what I am doing or how to do this, and/or if this stuff is all compatible with Elecraft and N3FJP AC.
--
Jim K9TF
--
k1oj
ditdit

Re: Not Sending CW with Elecraft

Jim K9TF <jim.gmforum@...>
 

The more I look into this, even I do not want to, is to use K1EL Winkeyer box. Or some sort of virtual com port software that works with N3FJP software. Some one suggested to use  LP Bridge   Ihttp://www.telepostinc.com/LPB.html have no Idea what I am doing or how to do this, and/or if this stuff is all compatible with Elecraft and N3FJP AC.
--
Jim K9TF

Re: Problem with ACL 6.6

Scott Davis
 

Hi Bruno,

Thanks for your e-mail.  Correcting your station location selection by using the drop down as detailed in in Step 3 here will do the trick:


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Bruno Haineault <w4afk.home@...>
To: N3FJPSoftwareUsers <N3FJPSoftwareUsers@groups.io>
Sent: Sun, Mar 8, 2020 6:34 am
Subject: [N3FJPSoftwareUsers] Problem with ACL 6.6

Getting this error message after updating to ACL 6.6

TQSL software reports:
 
TQSL Version 2.4.7 [v2.4.7]
Error: The selected station location could not be found
Final Status: Command Syntax Error (10)

Re: Dynamic QSO Map Display

Scott Davis
 

Hi Chuck,

Thanks for your e-mail.  Assuming your question is in reference to the contest software, this will get you going:

Capture.JPG



Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Chuck Chamblee, W4LAC <cchamblee25@...>
To: N3FJPSoftwareUsers <N3FJPSoftwareUsers@groups.io>
Sent: Sun, Mar 8, 2020 3:18 am
Subject: Re: [N3FJPSoftwareUsers] Dynamic QSO Map Display

On the Band Map display panel, how can I prevent new spots from appearing again if I've already logged them?
--
73,
W4LAC

Re: Time disappeared in DX Spotting window

Scott Davis
 

Hi Mel,

Thanks for your e-mail.  You dragged the column to a 0 length.  Just grab the edge of the columns until you find it and drag it back open.

Enjoy!


73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Mel - N7GCO - Cheney, WA <teammel@...>
To: N3FJPSoftwareUsers <N3FJPSoftwareUsers@groups.io>
Sent: Sat, Mar 7, 2020 11:26 pm
Subject: [N3FJPSoftwareUsers] Time disappeared in DX Spotting window

While doing the ARRL DX SSB contest, the time disappeared from the large DX spotting window. Not sure why. How do I get it back?

Problem with ACL 6.6

Bruno Haineault
 

Getting this error message after updating to ACL 6.6

TQSL software reports:
 
TQSL Version 2.4.7 [v2.4.7]
Error: The selected station location could not be found
Final Status: Command Syntax Error (10)

Re: Dynamic QSO Map Display

Chuck Chamblee, W4LAC
 

On the Band Map display panel, how can I prevent new spots from appearing again if I've already logged them?
--
73,
W4LAC

Time disappeared in DX Spotting window

Mel - N7GCO - Cheney, WA
 

While doing the ARRL DX SSB contest, the time disappeared from the large DX spotting window. Not sure why. How do I get it back?

Re: Unwanted spots showing up

Craig
 

Thanks Scott,  I will see how that goes.

73
Craig 
VK2KDP

On Sat, Mar 7, 2020 at 10:09 PM Scott Davis via Groups.Io <SNKDavis=aol.com@groups.io> wrote:
Hi Craig,

Thanks for your e-mail.  Make sure you also block the Digital spots, which are in the CW sub band.

Enjoy!


73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Craig <crvalosin@...>
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Sent: Sat, Mar 7, 2020 4:51 am
Subject: [N3FJPSoftwareUsers] Unwanted spots showing up

Hi all,

On my dx spotting I have the  box Block CW checked, but I am still seeing CW spots come through.  This used to work, but in the last month or so it stopped.

Anyone else having issues with this?  Is there something else that needs to be checked or is it a glitch? 

Thanks
Craig
VK2KDP/KK2V

Re: Ft 950 interface

Robb Zarges <RZarges@...>
 

Update.

Info one Ted the single to the rig and rebooted the computer and viola its working again.  

Thanks Scott for this incredible piece of software.

Thanks,

Robb Zarges, PhD
508-831-8248


From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> on behalf of Scott Davis via Groups.Io <SNKDavis@...>
Sent: Saturday, March 7, 2020 8:18:17 PM
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Subject: Re: [N3FJPSoftwareUsers] Ft 950 interface
 
Hi Robb,

Thinking about this a bit more, your rig is responding to the request for frequency command.  

What specifically is not working?  What changes did you make immediately prior to the new behavior?

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Robb Zarges <RZarges@...>
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Sent: Sat, Mar 7, 2020 5:00 pm
Subject: Re: [N3FJPSoftwareUsers] Ft 950 interface

Hmmm ok thanks Scott.  

Thanks,

Robb Zarges, PhD
508-831-8248

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> on behalf of Scott Davis via Groups.Io <SNKDavis@...>
Sent: Saturday, March 7, 2020 1:19:52 PM
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Subject: Re: [N3FJPSoftwareUsers] Ft 950 interface
 
Hi Robb,

Thanks for your e-mail.  I'm sorry that you have run into trouble.  I'm not familiar with the Yaesu 950 myself, but I have had lots of good reports.  Typically, when the software is receiving frequency from the rig, the rig will also respond to commands.  Since it is not, and since it was working and then stopped without changing the software, it is very likely that whatever is at play is external to the software.  It could be your rig settings, your cable or your com port driver.

I'm sorry I don't have more in the way of specifics to suggest.  Perhaps someone more familiar with the 950 will have some ideas for you.

Good luck! 

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Robb Zarges <RZarges@...>
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Sent: Sat, Mar 7, 2020 12:39 pm
Subject: [N3FJPSoftwareUsers] Ft 950 interface

hello,
My FT 950 rig has stopped sending to the N3JFP software but receives info from the software.  Any help would be appreciated. 

Thanks,

Robb Zarges, PhD
508-831-8248

Re: Ft 950 interface

Scott Davis
 

Hi Robb,

Thinking about this a bit more, your rig is responding to the request for frequency command.  

What specifically is not working?  What changes did you make immediately prior to the new behavior?

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Robb Zarges <RZarges@...>
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Sent: Sat, Mar 7, 2020 5:00 pm
Subject: Re: [N3FJPSoftwareUsers] Ft 950 interface

Hmmm ok thanks Scott.  

Thanks,

Robb Zarges, PhD
508-831-8248

From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> on behalf of Scott Davis via Groups.Io <SNKDavis@...>
Sent: Saturday, March 7, 2020 1:19:52 PM
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Subject: Re: [N3FJPSoftwareUsers] Ft 950 interface
 
Hi Robb,

Thanks for your e-mail.  I'm sorry that you have run into trouble.  I'm not familiar with the Yaesu 950 myself, but I have had lots of good reports.  Typically, when the software is receiving frequency from the rig, the rig will also respond to commands.  Since it is not, and since it was working and then stopped without changing the software, it is very likely that whatever is at play is external to the software.  It could be your rig settings, your cable or your com port driver.

I'm sorry I don't have more in the way of specifics to suggest.  Perhaps someone more familiar with the 950 will have some ideas for you.

Good luck! 

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Robb Zarges <RZarges@...>
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Sent: Sat, Mar 7, 2020 12:39 pm
Subject: [N3FJPSoftwareUsers] Ft 950 interface

hello,
My FT 950 rig has stopped sending to the N3JFP software but receives info from the software.  Any help would be appreciated. 

Thanks,

Robb Zarges, PhD
508-831-8248

Re: Ft 950 interface

Robb Zarges <RZarges@...>
 

Hmmm ok thanks Scott.  

Thanks,

Robb Zarges, PhD
508-831-8248


From: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io> on behalf of Scott Davis via Groups.Io <SNKDavis@...>
Sent: Saturday, March 7, 2020 1:19:52 PM
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Subject: Re: [N3FJPSoftwareUsers] Ft 950 interface
 
Hi Robb,

Thanks for your e-mail.  I'm sorry that you have run into trouble.  I'm not familiar with the Yaesu 950 myself, but I have had lots of good reports.  Typically, when the software is receiving frequency from the rig, the rig will also respond to commands.  Since it is not, and since it was working and then stopped without changing the software, it is very likely that whatever is at play is external to the software.  It could be your rig settings, your cable or your com port driver.

I'm sorry I don't have more in the way of specifics to suggest.  Perhaps someone more familiar with the 950 will have some ideas for you.

Good luck! 

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Robb Zarges <RZarges@...>
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Sent: Sat, Mar 7, 2020 12:39 pm
Subject: [N3FJPSoftwareUsers] Ft 950 interface

hello,
My FT 950 rig has stopped sending to the N3JFP software but receives info from the software.  Any help would be appreciated. 

Thanks,

Robb Zarges, PhD
508-831-8248

60 meter dx spot

rino deschenes <ve9vic@...>
 

In my dx filter setting I blocked 2 meter and up only and in the mode I blocked phone and digital but I do not get 60 meter spot ?

 

Re: Ft 950 interface

Scott Davis
 

Hi Robb,

Thanks for your e-mail.  I'm sorry that you have run into trouble.  I'm not familiar with the Yaesu 950 myself, but I have had lots of good reports.  Typically, when the software is receiving frequency from the rig, the rig will also respond to commands.  Since it is not, and since it was working and then stopped without changing the software, it is very likely that whatever is at play is external to the software.  It could be your rig settings, your cable or your com port driver.

I'm sorry I don't have more in the way of specifics to suggest.  Perhaps someone more familiar with the 950 will have some ideas for you.

Good luck! 

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Robb Zarges <RZarges@...>
To: N3FJPSoftwareUsers@groups.io <N3FJPSoftwareUsers@groups.io>
Sent: Sat, Mar 7, 2020 12:39 pm
Subject: [N3FJPSoftwareUsers] Ft 950 interface

hello,
My FT 950 rig has stopped sending to the N3JFP software but receives info from the software.  Any help would be appreciated. 

Thanks,

Robb Zarges, PhD
508-831-8248

Re: Dynamic QSO Map Display

Scott Davis
 

Hi Chuck,

Thanks for your e-mail.  Yes, this page will get you going:


Enjoy!

73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: Chuck Chamblee, W4LAC <cchamblee25@...>
To: N3FJPSoftwareUsers <N3FJPSoftwareUsers@groups.io>
Sent: Sat, Mar 7, 2020 9:47 am
Subject: [N3FJPSoftwareUsers] Dynamic QSO Map Display

Pardon me if I missed this, but does ACL have the ability to display a live graphical QSO map, or at least feed live data to another app (like Google Maps) for populating a map with your live QSOs?

--
73,
W4LAC

Ft 950 interface

Robb Zarges <RZarges@...>
 

hello,
My FT 950 rig has stopped sending to the N3JFP software but receives info from the software.  Any help would be appreciated. 

Thanks,

Robb Zarges, PhD
508-831-8248

Dynamic QSO Map Display

Chuck Chamblee, W4LAC
 

Pardon me if I missed this, but does ACL have the ability to display a live graphical QSO map, or at least feed live data to another app (like Google Maps) for populating a map with your live QSOs?

--
73,
W4LAC

Re: Contact count not correct.

Scott Davis
 

Hi Ed,

Thanks for your e-mail.  After you complete the process, click File > Reset Counter and enter your current highest QSO count.

Enjoy!


73, Scott
N3FJP

Serving the Amateur Radio community with contesting and general logging software since 1997.

1 Peter 3 vs 15: Always be prepared to give an answer to everyone who asks you to give the reason for the hope that you have. But do this with gentleness and respect...


-----Original Message-----
From: abcd wxyz via Groups.Io <W6OLA@...>
To: N3FJP Group <n3fjpsoftwareusers@groups.io>
Cc: W6OLA Ed <w6ola@...>
Sent: Sat, Mar 7, 2020 9:12 am
Subject: [N3FJPSoftwareUsers] Contact count not correct.

I have up loaded contact information from two separate logging programs that I no longer use. As expected, there are dupes in some areas. As I delete these dupes the contact count number does not change. I expected it to decrease as I deleted. What should I do to bring the contact count into alignment with the actual number of contacts?
Thanks for your help.
Ed W6OLA

Contact count not correct.

abcd wxyz <W6OLA@...>
 

I have up loaded contact information from two separate logging programs that I no longer use. As expected, there are dupes in some areas. As I delete these dupes the contact count number does not change. I expected it to decrease as I deleted. What should I do to bring the contact count into alignment with the actual number of contacts?
Thanks for your help.
Ed W6OLA

Re: Unwanted spots showing up

Buzz Kutcher. K3GWK
 

Make sure you send a Tell Cluster command after you make your Band/Mode selections.

 

73,

Buzz, K3GWK

 

Sent from Mail for Windows 10